Alpha Professional Tools Ecocutter ECC-125 User manual

Part No: ECC-125

ECC-STAND

ECC-TABLE

103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114

www.alpha-tools.com

Alpha®Ecocutter

Dry Tile Cutting System

Instruction Manual

MANUAL

Version 5

TABLE OF CONTENTS

Introduction................................................................................................................ 3

About the Symbols............................................................................................... 3

Safety Instructions ............................................................................................... 3

Ecocutter Stand......................................................................................................... 6

Components.......................................................................................................... 6

Assembly of Ecocutter Stand.............................................................................. 7

Caster Installation................................................................................................. 8

Ecocutter Stand Schematic and Parts List ........................................................... 10

Ecocutter Table........................................................................................................ 12

Components........................................................................................................ 12

Instructions on Removing Ecocutter Table from Box..................................... 13

Instructions on Handling Ecocutter Table........................................................ 14

Recommended Method ...................................................................................... 15

Assembling Table to Stand................................................................................ 17

Installation of the Hose Holder to the Saw Base ............................................. 20

Installation of the Angle and Rip Guide............................................................ 22

Ecocutter Table Schematic..................................................................................... 24

Ecocutter Table Parts List ...................................................................................... 25

Installation of Ecocutter to Saw Base ................................................................... 26

Stabilizer................................................................................................................... 28

Blade Height Adjustment........................................................................................ 29

Table Side Extension Support................................................................................ 32

Ecocutter Dust Hose and Bag Installation............................................................ 33

Ecocutter Schematic............................................................................................... 36

Ecocutter Parts List................................................................................................. 37

INTRODUCTION

Thank you for purchasing theAlpha®Ecocutter Dry Tile Cutting System. Please read this

instructionmanual thoroughly to ensure safe andcorrect use of theEcocutter Dry TileCut-

ting System. Keep this manual in a place where operators can access it easily whenever

necessary.

ABOUT THE SYMBOLS

According to the hazard level, all safety notes in this manual are classied into “DANGER”,

“WARNING”, and “CAUTION”.

DANGER! Death or serious personal injury is imminent when handling this

stone cutter incorrectly.

WARNING! There is a possibility of death or serious personal injury when

handling this stone cutter incorrectly.

CAUTION! Thereis apossibilityofpersonalinjury or propertydamagewhen

handling this stone cutter incorrectly.

Note: In some situations, failing to observe WARNING notes could result in death or

serious personal injury. Be sure to read and observe the safety notes to ensure

safe and correct use of the stone cutter.

CAUTION!

The following are important notes for products, operation, and maintenance applicable to

this stone cutter.

SAFETY INSTRUCTIONS

Read all these instructions before attempting to operate this product.

WARNING!

When using electric tools, basic safety precautions should always be followed to reduce the

risk of re, electric shock, and personal injury, including the following.

For Safe Operation

1. Keep work area clean

Cluttered areas and benches invite injuries.

2. Consider work area environment

Do not expose power tools to rain. Do not use power tools in damp or wet locations

without GFCI protection. Keep work areas well lit. Do not use the tool in presence of

ammable liquids or gases.

3. Guard against electric shock

Prevent body contact with grounded surfaces. For example: pipes, radiators, ranges,

and refrigerator enclosures; use grounded outlets.

4. Keep children and visitors away

Do not let visitors contact tool or extension cord. All visitors should be kept away from

work area. Keep out of reach of children.

5. Tool Storage

When not in use, tools should be stored in a secure dry location. A locked storage area

or high shelf out of children’s reach is ideal.

6. Do not force the tool

It will do the job better and be safer at the rate for which it was intended.

7. Use the right tool

Do not force a small tool or attachment to do the job of a heavy-duty tool. Do not use

the tool for purposes it is not designed for – (for example – do not use stone cutter for

cutting tree limbs or logs.)

8. Dress properly

Do not wear loose clothing or jewelry. Items such as these can be caught in moving

parts. Rubberglovesandnon-skidfootweararerecommendedwhenworkingoutdoors.

Wear protective hair covering to contain long hair.

9. Use safety equipment

Always wear safety glasses and if necessary, a face shield, dust mask and hearing

protection.

10. Do not abuse the electrical cord

Never carrythe toolby theelectrical cordor pullit todisconnect fromreceptacle. Keep

the electrical cord away from heat, oil and sharp edges.

11. Secure workpiece

Use clamps or a vise to hold workpiece rather than using your hands.

12. Do not overreach

Keep proper footing and balance at all times.

13. Maintain tools with care

Keep tools sharp and clean for better and safer performance. Follow instructions for

lubricating and changing accessories. Inspect the electrical cord periodically and

if damaged, have it repaired by authorized service facility. Inspect extension cords

periodically and replace if damaged. Keep handles dry, clean and free from oil and

grease.

14. Disconnect tools

Disconnectthetoolfromthepowersupplywhennotinuse,beforeservicing,andwhen

changing accessories, such as blades, bits, cutters.

15. Remove adjusting keys and wrenches

Check to see that keys and adjusting wrenches are removed from the tool before

turning it on.

16. Avoid unintentional starting

Do not carry a plugged-in tool with nger on switch. Be sure the switch is off when

plugging in.

17. Outdoor use extension cords

When tool is used outdoors, use only extension cords intended for use outdoors and

so marked.

18. Stay alert

Use caution and do not operate tool when you are tired or on medication.

19. Check for damaged parts

Beforeusingthetooleachday,aguardorotherpartthatisdamagedshouldbecarefully

checked to determine that it will operate properly and perform its intended function.

Check for alignment of moving parts, breakage of parts, mounting, and any other

conditions that may affect its operation.A guard or other part that is damaged should

be properly repaired or replaced by an authorized service center unless otherwise

indicated elsewhere in this instruction manual. Have defective switches replaced by

authorized service center. Do not use the tool if it cannot be turned on and off by the

switch.

20. Warning

The use of any other accessory or attachment other than recommended in this

instruction manualor the catalogmay present arisk of personalinjury and couldvoid

the warranty.

21. Only qualied technicians should repair this tool

This electric tool is manufactured in accordance with the standard safety rules. Only

experts may carry out the repair of electric tools; otherwise, it may cause considerable

danger for the operator.

ALPHA® ECOCUTTER STAND (ECC-STAND)

COMPONENTS:

1. 2 Bolts and Hardware (for folding leg assembly) (Part No. 200026)

2. 8 Bolts and Hardware (for casters)

3. 2 Locking Casters

4. 2 Legs (Front Saw Stand, Part No. 200020 — Rear Saw Stand, Part No. 200021)

5. 2 Wing Screws (Part No. 200024)

After removalof allcutting table basecomponents frompacking, check foreach itemlisted

below:











Figure-1

(Part No. 200022)

ASSEMBLY OF ECOCUTTER STAND

The following tools will be needed to assemble this base section of the cutting table for

the Ecocutter.

2 - 14mm wrenches

1 - 11mm wrench

1 - 10mm wrench

1. Position the two legs to create a scissor

conguration as shown in Figure 2.

Figure-2

2. Turn assembly on its side and align the

holes located at the center of each leg.

Insert one of the two large bolts (Part No.

200026) using a at washer on each side

followed by the nylon insert lock nut as

shown in Figure 3 and Figure 4.

Figure-3

Nylon Lock Nut

Figure-4

3. Tighten bolts until a slight gap remains

between the two legs. See Figure 5 and

Figure 6.

4. Legs mustmove freelyin ascissor motion

(See Figure 6). Note: an over tightened

condition will cause binding of the legs.

Figure-5

Figure-6

Air Gap

CASTER INSTALLATION

1. Place and align caster mounting plate with mounting holes on base

of stand leg as shown in Figure 7 and Figure 8.

2. Insert the four bolts for the

casters with washers on each

side and lock nut as shown in

Figure 9.

3. Tighten until snug.

Figure-7

Figure-8

Figure-9

5. See Figure 11 for complete assembled

base stand in the opened position.

6. See Figure 12 for complete assembled

base stand in the folded position used

for transport.

4. Repeat process for second caster as

shown in Figure 10.

Figure-10

Figure-11

Figure-12

Other manuals for Ecocutter ECC-125

This manual suits for next models

Table of contents

Other Alpha Professional Tools Cutter manuals

Alpha Professional Tools

Alpha Professional Tools ESC-125 User manual

Alpha Professional Tools

Alpha Professional Tools AWS-110 User manual

Alpha Professional Tools

Alpha Professional Tools Ecocutter ECC-125 User manual

Alpha Professional Tools

Alpha Professional Tools WBC5KIT User manual

Alpha Professional Tools

Alpha Professional Tools PSC-150 User manual

Alpha Professional Tools

Alpha Professional Tools ESC-125 User manual

Alpha Professional Tools

Alpha Professional Tools Ecocutter ECC-125 Specification sheet

Alpha Professional Tools

Alpha Professional Tools PSC-600 User manual

Alpha Professional Tools

Alpha Professional Tools ESC-150 User manual

Alpha Professional Tools

Alpha Professional Tools WBCKIT User manual

Alpha Professional Tools

Alpha Professional Tools COTE-04 User manual

Popular Cutter manuals by other brands

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Original instructions

Makita

Makita DCS552 instruction manual

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 user manual

Makita

Makita 4112HS instruction manual

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S manual

Hitachi

Hitachi CM 4SB2 Safety instructions and instruction manual

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 instruction manual

GCC Technologies

GCC Technologies AFJ-24S user manual

DeWalt

DeWalt XR LI-ION DCS350N manual

Baudat

Baudat ES1 instruction manual

Mafell

Mafell ZAF 200 Operating instructions and spare parts list

Makita

Makita 4100NH instruction manual

Formax

Formax FD 574 Operator's manual

EINHELL

EINHELL TE-MA 1500 Original operating instructions

Husqvarna

Husqvarna Cut-n-Break K 760 Operator's manual

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Operator's manual

TRI tool

TRI tool 301A user manual

Roller

Roller King 1 1/4 operating instructions