AJA D10CEA User manual

D10CEA SDI to Component/

Composite Video with 4

Channel Audio

Converter

User Manual

June 28, 2005 P/N 101637-00

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

AJA D10CEA SDI to Component/Composite Converter User Manual — Introduction

Introduction

The D1OCEA converts SDI video with embedded audio to 10-bit component or

composite analog video and 4 channel balanced analog audio. The video outputs can

be conﬁgured as YPbPr (Betacam or SMPTE/EBU N10), RGB, composite or Y/C

(S-Video). Two re-clocked loop-thru SDI outputs are also provided. This versatile

low-cost converter is ideal for video/audio monitoring.

The 4 channel analog audio outputs can be wired in a balanced or unbalanced

conﬁguration. All audio output channels can be selected as group 1-4 from SMPTE

embedded audio. You have four settings of Audio level to choose from.

Output connections for video and audio are available on a 25 pin “D” subminiature

connector. A break-out cable is supplied with the converter for this purpose.

You can conﬁgure video and audio from a DIP switch accessed through a cut-out in

the converter’s case.

Features

•

SDI to analog audio and video converter

•

SDI with embedded audio input

•

2 re-clocked, loop-thru SDI outputs

•

10-bit component or composite analog video outputs

•

4 channel balanced analog audio output

•

Selectable audio level

•

Selectable audio channel group

•

External DIP switch user interface for configuration

Block Diagram

D10CEA SDI Video with Embedded Audio Converter, Block Diagram

Serial

Video

with Embedded Audio

Filter

Audio

Filter

DIP

Switch

User

Interface

for

Feature

Selection

Video and

Audio D/A

ReClock

COMPONENT OUTPUTS (selected by DIP switch)

Serial Video Out 1

Serial Video Out 2

COMP

Break-out

Cable

Clocked Loop-through SDI Outputs B

Channel 1 Right

Channel 1 Left

Channel 2 Right

Channel 2 Left

I/O Connections

D10CEA and Break-Out Cable

SDI Input

SDI Loop

+ 5VDC

Configuration

Determined by

DIP switch on

Output 1

Output 2

Power

Input

BNC

back of

Converter

DB25 Connector

Attaches to Break-out

Cable (shown below)

providing Audio and

Video Outputs

Break-out Cable

(DB25 to 4 XLRs

and 3 BNCs)

AJA D10CEA SDI to Component/Composite Converter User Manual — User Controls

User Controls

The user interface for the D10CEA is an 8-switch DIP accessible

through a cut-out in the bottom of the unit. Use the DIP switches

to conﬁgure video outputs, pedestal, blanking, select audio

channel groups, and set audio level.

Switches 1 through 4 conﬁgure video output format. Switches 4

through 8 select the audio channel group and audio level. The

exact function of each DIP switch and what it controls is

described on the following pages.

Switch 1—Select Component (COMPNT) or Composite (CMPSTE) Out

Switch 2—Selects YPbPr/YC or RGB Component Outputs

Switch 3—Configure Pedestal For Composite

Note:

There is no effect with 625 input.

RIGHT LEFT

CMPSTE:

Selects composite video output

COMPNT:

Selects component video output

RIGHT LEFT

RGB:

Selects RGB

YPbPr/YC:

Selects YPbPr/YC component video out

RIGHT LEFT

7.5 IRE pedestal for NTSC (also selects

BETA 525 levels for YPbPr)

No pedestal (also selects SMPTE levels for

YPbPr)

DIP Switches

LEFT RIGHT

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

Switch 4—Configure Blanking

Switches 5 and 6—Select an Audio Channel Group for Output

Together these two switches select the group of audio channels that will be routed to the

XLR connectors on the break-out cable. Each audio group has four channels,

corresponding to the four connectors. The following table shows the group and channel

assignments selected by each switch position for the two DIP switches.

Switches 7 and 8——Select Audio Levels for Output

Together these two switches select audio output levels at the XLR outputs. The following

table shows the level selected by each switch position for the two DIP switches.

RIGHT LEFT

WIDE Blanking:

Vertical—

Line numbers indicate where video starts)

line 20, ﬁeld 1; line 20, ﬁeld 2 (525 line)

line 23, ﬁeld 1; line 336, ﬁeld 2 (625 line)

Horizontal—

Active video line duration

ITU-R/SMPTE (710 pixels NTSC,

702 pixels PAL)

NARROW (NAR) Blanking:

Vertical—

Line numbers indicate where video starts

line 13, ﬁeld 1; line 12, ﬁeld 2 (525 line)

line 10, ﬁeld 1; line 322, ﬁeld 2 (625 line)

Horizontal—

Active video line duration's)

ITU-R.470 (720 pixels PAUNTSC)~-

Group and Channels S5 S6

Group 0:

Channels 1 to 4

0ff (Left) 0ff (Left)

Group 1:

Channels 5 to 8

0n (Right) 0ff (Left)

Group 2:

Channels 9 to 12

0ff (Left) 0n (Right)

Group 3:

Channels 13 to 16

0n (Right) 0n (Right)

Audio Level (dbu) S7 S8

+4.00 dbu 0ff (Left) 0ff (Left)

+2.00 dbu 0n (Right) 0ff (Left)

0.00 dbu 0ff (Left) 0n (Right)

-14.00 dbu 0n (Right) 0n (Right)

AJA D10CEA SDI to Component/Composite Converter User Manual — User Controls

Output Selection

Matrix For Video

Output 2 (3 BNCs)

The following table shows the combinations of DIP switch settings required to conﬁgure the

three BNCs on the break-out cable.

Examples of Typical DIP Switch Settings

Output Format DIP Switch

DIP Switch

1 composite & 1 Y/C (pedestal) CMPSTE/

RIGHT

YPbPr/YC

N/A

RIGHT

1 composite & 1 Y/C (no pedestal) COMPNT/

RIGHT

YPbPr/YC/YC

N/A

LEFT

RGB COMPNT/

LEFT

RGB/RIGHT LEFT

SMPTE component (BETA625) COMPNT/

LEFT

YPbPr/YC/YC

LEFT

BETA 525 component COMPNT/

LEFT

YPbPr/YC/YC

LEFT

RIGHT

SMPTE

Component

Format

Pedestal

Blanking

Audio Group 0

Audio Group 1

Audio Level 0

Audio Level 1

Beta

Component

Format

Pedestal

Blanking

Audio Group 0

Audio Group 1

Audio Level 0

Audio Level 1

Composite

Format

Pedestal

Blanking

Audio Group 0

Audio Group 1

Audio Level 0

Audio Level 1

Selects:

Component

YPbPr (SMPTE)

Pedestal Off

Narrow Blanking

Audio Group 0 (channels 1-4)

Audio Level +4.00 dbu

Selects:

Component

YPbPr (Beta)

Pedestal On

Narrow Blanking

Audio Group 0 (channels 1-4)

Audio Level +4.00 dbu

Selects:

Composite

Composite and Y/C

Pedestal On

Narrow Blanking

Audio Group 0 (channels 1-4)

Audio Level 0.00 dbu

Installation

Typically, D10CEA installation consists of the following:

disconnect +5VDC from the convertor

conﬁgure the DIP switch for the desired equipment conﬁguration and video formats

connect video equipment to the convertor BNCs

apply +5VDC power to the converter (AJA power supply model DWP)

Specifications

Item Speciﬁcation

Serial Input SMPTE 259M with embedded audio

, 1 BNC

Outputs Video: YPbPr - SMPTE, EBU-N10, Betacam, RGB, NTSC,

PAL, YC (S-Video), 10-bits

2 SDI Re-clocked loop-thru, 2 x BNC

Audio: 4 Channel Balanced/Unbalanced. Audio breakout

cable for balanced output included with unit.

Video/Audio Outputs: 1 25-pin D connector

Audio Groups

1, 2, 3, 4

Frequency Response +/- .25dB to 5.5MHz (Y Video)

+/- .5dB to 20 KHz (Audio)

Audio Level Adjustments -14, 0, +2, +4 dBu

Power

(AJA power supply model DWP)

5v DC regulated, 4 watt

Size 5.8" x 3.1" x 1" (147 x 79 x 25 mm)

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

Table of contents

Other AJA Media Converter manuals

AJA

AJA OG-HA5-4K Operating instructions

AJA

AJA Hi5-4K Operating instructions

AJA

AJA HA5-12G Operating instructions

AJA

AJA HA5-4K Operating instructions

AJA

AJA FS1-X User manual

AJA

AJA ADA4 Mini-Converter User manual

AJA

AJA V2Analog Original operating instructions

AJA

AJA HDP3 Operating instructions

AJA

AJA ROI Series Operating instructions

AJA

AJA HI5-PLUS-R0 Operating instructions

AJA

AJA V2Digital Original operating instructions

AJA

AJA HB-T-HDMI Original operating instructions

AJA

AJA OG-Hi5-4K-Plus Operating instructions

AJA

AJA FiDO 3G Series Operating instructions

AJA

AJA 12G-AMA Operating instructions

AJA

AJA U-TAP Series Operating instructions

AJA

AJA IPTR-10G2 Series Operating instructions

AJA

AJA FS2 Operating instructions

AJA

AJA 4K2HD Operating instructions

AJA

AJA HD10AM User manual

AJA

AJA HA5-Plus Operating instructions

AJA

AJA Io 4K/XT User manual

AJA

AJA HDP User manual

AJA

AJA FS4 Original operating instructions

Popular Media Converter manuals by other brands

SoundTraxx

SoundTraxx Blunami BLU-2200 user guide

SPROLINK

SPROLINK VA1 user manual

Acclaim Lighting

Acclaim Lighting DDC-1-AC user guide

Nikon

Nikon AF-S TC-20E III user manual

Axis

Axis AXIS Q7406 user manual

Omega

Omega TAC80B-J instruction sheet

Zoom

Zoom Thunderbolt TAC-2R Operation manual

OST

OST iConverter 10/100M quick start guide

Vertiv

Vertiv Netsure user manual

birddog

birddog MINI user guide

Roland

Roland GI-10 owner's manual

Wallenstein

Wallenstein WX310 Operator's manual

Pace

Pace MSS 200-1 Service manual

Solar Converters

Solar Converters EQ 12/24-50 manual

CYP

CYP EL-7400V Operation manual

TIE

TIE MIDI 1i1o user manual

DCS

DCS Vivaldi Upsampler user manual

Westermo

Westermo MCW-211 SERIES user guide