AirTies Air 4240 User manual
Гарантия 3 года
CD простой установки
Поддержка 7/24
8 800 100 02 80
8 800 507 44 40
2
1INTRODUCTION 4
1.1 Minimum System Requirements 4
1.2 Package Contents 4
1.3 Front Panel 4
1.4 Back Panel 5
1.5 Main Features 5
2. INSTALLATION 5
2.1 Installing the Air 4240 as an Access Point 5
2.1.1 Connecting the Cables for Access Point Mode 6
2.1.2 Connecting to the Air 4240 6
2.1.3 Advanced Settings Using the AirTies
Access Program 6
2.1.4 Accessing the advanced settings with a Static IP 10
2.2 Installing the Air 4240 as a Router 10
2.2.1 Connecting the Cables for the Router Mode 10
2.2.2 Connecting to the Air 4240 (In Router mode) 10
2.2.3 Advanced Settings Using the AirTies
Access Program (in Router mode) 10
3 ADVANCED SETTINGS 12
3.1. Operation Mode 12
3.2 Internet settings 12
3.2.1 Internet status and statistics 12
3.2.2 Internet Settings 12
3.2.3 DNS Settings 13
3.3 LAN 13
3.3.1 IP and DHCP Settings 13
3.3.2 LAN Clients 14
3.4 Wireless Settings 15
3.4.1 Connecting to the Air 4240 15
3.4.2 Wireless Network Settings 15
3.4.3 Wireless Security Settings 16
3.4.4 MAC Address Filtering 18
3.4.5 AirTies Mesh Settings 18
Manual Overview 3
Safety and Maintenance 3
3.5 FIREWALL Settings 20
3.5.1 Access Control 20
3.5.2 MAC Address Filtering 21
3.5.3 URL Filters 21
3.5.4 Anti-DoS 21
3.6 NAT 22
3.6.1 Port Forwarding 22
3.6.2 DMZ 23
3.7 Routing 23
3.7.1Static Routing 23
3.8 Management 24
3.81 Password Settings 24
3.8.2 Remote Management 24
3.9 DDNS 25
3.9.1 DDNS Settings 25
3.10 Tools 26
3.10.1 Firmware Upgrade 26
3.10.2 Time Settings 26
3.11 Reports 26
3.11.1 System Logs 27
3.11.2 Log Settings 27
4 TECHNICAL PROPERTIES 27
5 PHYSICAL CHARACTERISTICS 27
Contents
3
This manual guides you through the steps necessary for setting up and conguring your
AirTies device. Please read this manual carefully before beginning the installation process.
The Warranty does not cover failure or damage as a result of not following the instructions
in the manual. AirTies will not be held responsible in such circumstances.
The User Manual is an important resource you can refer to for safe and proper use of your
device. Please retain it for future reference.
• In order to prevent damage to your device, be sure to keep it in its original box during
transportation.
• The device must be used solely with its original power adapter.
• Do not insert a PSTN (phone) plug into the LAN port.
• If you encounter any problems, do not open or disassemble the device. Call AirTies
Technical Support.
• In order to prevent electric shock, do not operate the device in wet or damp areas.
• In the event of a gas leak, do not use the device. Do not turn the device on or off. Do not
plug or unplug the power cord.
• Avoid using the device in dusty environments. If dust buildup should occur, use a dry
cloth to remove the dust.
• To clean the exterior of the device use a dry cloth. Do not attempt to clean the interior.
There are no user serviceable components inside.
• For information regarding the installation and conguration of the device consult the
remainder of this manual.
• Remove all protective plastic on the top and bottom of your device before you start
using it.
• The average usage life of the device is 7 years as determined by the Authority of
Industry and Trade.
This manual has been prepared by AirTies Wireless Networks Corporation. All rights reserved.
Manual Overview
Safety and
Maintenance
4
The AirTies Air4240 is an IEEE 802.11b/g compliant, 54 Mbps wireless communication
device that can be used as a Wireless Access Point, Repeater, or a Router.
You can connect the AirTies Air4240 to a wired modem or router through one of the Ethernet
ports to setup a wireless local network and enable your wireless computers to access the
Internet.
As a repeater, the Air4240 makes it possible to extend the coverage area of a wireless
network. AirTies Mesh Technology is used for this purpose.
The AirTies Mesh Technology resolves problems such as loss of wireless signal or limited
coverage area often encountered in multiple-story or reinforced concrete buildings. To
extend your wireless coverage, all you need to do is to add new Air4240 devices to your
wireless network and set them to function as repeaters. Computers on the network connect
to the Air4240 with the strongest signal, and reach the router or the wired network through
the AirTies Mesh Network.
• For installation and conguration: a PC that has an Ethernet interface or 802.11 b/g/n
compatible wireless capability, and is running any version of Windows, UNIX, Linux or
Mac Operating Systems and a Web browser
• For the AirTies ADSL Utility: 32 bit Windows 98/ME/2000/XP/Vista
The device does not need to be connected to a PC during normal operation.
1INTRODUCTION
1.1 Minimum System
Requirements
1.3 Front Panel
1.2 Package
Contents
LED LIGHT STATUS
Blue The device is “ON”.
Off The device is “OFF”.
Red Internet connection established and active
Red Flashing Connecting to the Internet
Off No Internet connection
Red Wireless network connection established and
active
Red ashing Data exchange on the wireless network
connection
Off No wireless network connection
Red WAN connection established and active
Red ashing Data exchange on the WAN connection
Off No WAN connection.
Red LAN connection established and active
Red ashing LAN connection active. There is data
exchange.
Off No LAN connection
ETHERNET
WAN
4
1 2 3
5 6
Please check to make sure all the parts listed below are included in the box:
1. Air 4240 54 Mbps Wireless 4-port Router
2. 9V Power adapter
3. Ethernet cable
4. AirTies Easy Setup CD
5. Quick Installation Guide
6. Warranty Card and Certicate of Compliance
3 Warranty
Card
Wireless life
7/24 people support
+90 212 444 0 239
Three year warranty
Lifetime enjoyment
One touch setup
Simple & easy to use
Quik Installation
Guide
Wireless life
Air 4240 54 Mbps Wireless 4-port Router
C D Ε ύ κ ολ η ς Ε γ κ α τ ά σ τ α σ η ς
Ai r T i e s AD S L Ut i l i t y ve r s i o n : v4 . 3 . 3 . 3
7/24 τηλ εφω νι κή γρα μμή
τεχνι κής υπ οστ ήρ� ���
801 100 0911
WAN
5
1.4 Back Panel
WAN Internet line port, connects to Internet gateway devices
ETHERNET 1-4 Ethernet ports
9V Power Port 9V power port, connects to the power adapter
• Multi-function: Router, 54Mbps Wireless Access Point, Repeater
• Repeater: AirTies Mesh Technology support for extending wireless coverage area in
concrete buildings where signal range problems are common.
• Router: Advanced router with DHCP server, NAT, NAPT, DMZ, VLAN*, RIPv1/v2 support
• USB Plug and Share feature gives you printer and le sharing capability throughout
your entire network from a single point*
• Advanced Wireless Security: WPA2- PSK, WPA2-802.1x, WPA-PSK, WPA-802.1x, WEP
wireless encryption standards support
•Firewall: Advanced anti-DoS SPI Firewall; MAC and IP address based ltering for
Internet access
• Uninterrupted technical support: 7/24 AirTies Call Center and Technical Support
(engineering support by the AirTies R&D team when needed)
•3 year extended warranty
* To be added with a rmware upgrade
1.5 Main Features
In Access Point mode, the Air 4240 provides wireless access capability on any network
where access to the Internet is through a wired ADSL modem, essentially making a wired
network wireless.
Note: How to change the mode of your device is explained in section 3.1 Operation Mode of
this manual.
Reset: Button to reset your device to default factory settings. (at the bottom of the device).
To reset the Air4240 to the default factory settings, while the device is on, press and hold the
reset button at the bottom of the device with the tip of a pencil or similar pointed object for 5
seconds.
2. INSTALLATION
2.1 Installing the
Air 4240 as an
Access Point
6
1. Connect the 9V power adapter included in the box to the power port of your device and
plug it into the wall outlet.
2. Using the Ethernet cable provided, connect one of the LAN ports of the Air 4240 to
the Ethernet port of your ADSL modem or an Ethernet port of a Switch on your wired
network.
The Air 4240 cable connections must be complete before you can establish a wireless
connection to it.
1. First, check to make sure the wireless network client (802.11b/g) of your computer is
enabled.
2. Find the “AirTies_Air4240” network (SSID) on the wireless network search page of your
wireless network client and connect to it.
Important: To be able to use the AirTies Access Program, your device must be connected to
an ADSL modem or a wired network and must have an IP address assigned to it.
1. By using the AirTies Access Program you can access the Web interface of your device to
congure the encryption settings and other advanced settings of your wireless network.
2. Insert the Air 4240 Easy setup CD into your computer.
3. The AirTies Access Program installation wizard will start automatically. Click Next> to
start the installation.
4. To complete the installation process, click “Finish” in the installation wizard.
2.1.1 Connecting the
Cables for Access
Point Mode
2.1.2 Connecting to
the Air 4240
2.1. 3 Advanced
Settings Using the
AirTies Access
Program
2
1
7
5. Once the installation is complete, the AirTies Access Program will start looking for AirTies
products that are connected to your computer.
6. At the end of the search, a list of all AirTies products connected to your computer will be
displayed.
7. Select the AirTies product whose Web interface you’d like to access and click “Connect”.
The login screen will come up. You do not need a password to access the Web interface.
Click “OK” to enter.
In Access Point mode, you can congure the advanced settings by connecting the Air 4240
directly to your computer. For this, you need to assign a static IP address to your computer’s
network adapter. The IP address has to be within the same network block as the default IP
address of the Air 4240 (192.168.2.254) and must be static (example: 192.168.2.5). Below
you will nd instructions for assigning a static IP address under various operating systems.
1. Go to Start -> Control Panel.
2. Click Network Connections.
2.1.4 Accessing the
Advanced Settings
with a Static IP
Windows XP
Air 4240
8
3. In the Network Connections window, right-click on the network adapter from which you
will connect to the Air 4240 (Wireless Network Connection, Local Area Connection) and
select Properties.
4. Right-click on Internet Protocol (TCP/IP) and select Properties.
5. In the Internet Protocol (TCP/IP) Properties window click on the Use the following IP
address button and enter an address in the 192.168.2.1 – 192.168.2.253 range in the IP
address eld.
6. The Subnet mask eld will have a default value of 255.255.255.0. You do not need to
change this value.
7. Click the OK button at the bottom of the window
1. Go to Start -> Control Panel.
2. Select Network and Sharing Center.
Windows Vista
9
3. At the Network and Sharing Center, select Manage network connections from the
menu on the left.
4. In the window that comes up, right-click on the network adapter from which you will
connect to the Air 4240 (Wireless Network Connection, Local Area Connection) and
select Properties.
5. In the Network Connection Properties window, double-click on Internet Protocol
version 4 (TCP/IPv4).
6. In the Internet Protocol version 4 (TCP/IPv4) window click on the Use the following IP
address button and enter an address in the 192.168.2.1 – 192.168.2.253 range in the IP
address eld.
7. The Subnet mask eld will have a default value of 255.255.255.0. You do not need to
change this value.
10
8.Click the OK button at the bottom of the window.
When nished, you can open a browser window (e.g. Internet Explorer, Firefox) and enter
192.168.2.254 in the address eld to access the Web interface for conguring advanced
settings
In Router mode, the Air 4240 allows you to connect your entire wired network to the Internet
wirelessly through a modem that does not have NAT or Firewall features.
Note: How to change the mode of your device is explained in section 3.1 Operation Mode of
this manual.
2.2 Installing the Air
4240 as a Router
1. Connect the 9V power adapter included in the box to the power port of your device and
plug it into the wall outlet.
3. Using the Ethernet cable provided, connect the WAN port of the Air 4240 to a cable
modem or Internet gateway.
2.2.1 Connecting the
Cables for the Router
Mode
The Air 4240 cable connections must be complete before you can establish a wireless
connection to it.
1. First, check to make sure the wireless network client (802.11b/g or 802.11n) of your
computer is enabled.
2. Find the “AirTies_Air4240” network (SSID) on the wireless network search page of your
wireless network client and connect to it.
1. By using the AirTies Access Program you can access the Web interface of your device to
congure the encryption settings and other advanced settings of your wireless network.
2. Insert the Air 4240 Easy setup CD into your computer.
3. The AirTies Access Program installation wizard will start automatically. Click Next> to
start the installation.
2.2.2 Connecting
to the Air 4240 (In
Router mode)
2.2.3 Advanced Set-
tings Using the
AirTies Access
Program (in Router
mode)
1
2
Table of contents
Other AirTies Network Router manuals
