Aidapt VY428S Manual

Solo Bed Lever (Slatted)

VY428S (Bulk - 6 Pieces)

VY428SA (Single Boxed)

Fixing and Maintenance Instructions

2 Ver 1 01/2015

I TRODUCTIO

This Bed Lever is for use with slatted beds and can be fitted to single,

double, queen and king size beds. Not for use on divan beds, please

use VY438 for divan beds.

The Bed Lever is not designed to prevent users falling from their bed.

This device is suitable for adult use only, it is not suitable for use with

children.

BEFORE USE

• Carefully remove all packaging. Avoid using any knives or other sharp

instruments as this may damage the surface of the product.

• Check that all parts are present before assembly (see fig. 1). If any

parts are missing do not attempt assembly and contact your supplier.

• Check the product for any visible damage If you see any damage or

suspect a fault, do not use your product as it may compromise your

safety, but contact your supplier for support.

ASSEMBLY I STRUCTIO S

1. Lay piece C on a flat surface and slide piece A onto the tubes on piece C and push firmly until the

holes align (see fig 2).

2. Secure with E-Clips (B). Make sure the E-clips are secure before proceeding (see fig. 3)

fig. 1

fig. 2 fig. 3

B. This equipment must be installed by a competent person and

a risk assessment undertaken as to the suitability of the Bed

Lever for the particular user and user’s bed. We would refer

customers to ‘Bed Rail Risk Management’ LAC umber 79/8

published by the HSE.

VY428S/VY428SA 160 kg (25 st.) weight limit

ote: Do not exceed the weight limit stated – doing so could

put the user at risk.

3 Ver 1 01/2015

ASSEMBLY I STRUCTIO S (Continued)

3. Insert extension poles (D) into the arms of piece C (see fig. 4) and slide in until the catches align with

the holes (see fig. 5).

4. Attach piece E onto extension

poles (D) (see fig. 6) and slide until

the catches align with the holes

(see fig. 5)

fig. 4

fig. 6

5. The catches can be depressed to

allow piece E to be moved depending

on the width of the bed (see fig. 7)

fig. 7

fig. 5

4 Ver 1 01/2015

CLEA I G

A useful guide to decontamination is MHRA leaflet DB2003(06).

Do not use abrasive cleaners as this could damage the surface of the equipment. For cleaning, wipe

with a clean cloth soaked in detergent solution and wring out. Depending on the detergent manufacturer’s

instructions the solution may be heated.

Wipe all surfaces of the equipment and the cloth should be re-immersed periodically and the detergent

changed frequently. The detergent should be rinsed or wiped off using a clean cloth immersed in clean

water and wrung out.

To disinfect make sure the equipment has been cleaned and dried and then wipe over with a clean cloth

and a compatible liquid disinfectant. After disinfecting clean with clean water and dry.

When using detergent or disinfectants then please refer to manufacturers’ instructions and if unsure then

consult your local Infection Control Specialist for advice.

This equipment can be cleaned/disinfected by moist heat at 80oC for a minimum of 1 minute or auto-

claved at 80oC for at least 1 minute. After cleaning or disinfecting treat all joints with a water dispersing

agent, e.g. WD40.

REISSUE

If you reissue or are about to reissue this product, please thoroughly check all components for their safety.

This includes:

• Tightness of all nuts/bolts/castors and other screw in/bolt in/push in components

• pholstery (if applicable) for security, splits, exposed staples, etc

• Straightness and integrity of all tubing and welds

If in any doubt, please do not issue or use, but immediately contact your supplier for service support.

When reissuing, a risk assessment must be undertaken as to the suitability of the Bed Lever for

the particular user and user’s bed.

fig. 8 fig. 9 fig. 10

ASSEMBLY I STRUCTIO S (Continued)

6. Remove the mattress from the bed and place the assembled bed lever onto the slats, making sure

that the back edge of piece C aligns with the recess of the bed (see fig 8.)

7. If not done in step 5 the width can now be adjusted to suit the size of the bed (see fig 9.)

8. Replace the mattress and the bed lever is now installed and ready to use (see fig. 10)

5 Ver 1 01/2015

IMPORTA T I FORMATIO

Do not allow children or unauthorised persons to play with the equipment or use the bed transfer aid

without proper supervision.

CARE & MAI TE A CE

Please make a safety check of the product at regular intervals or if you have any concerns.

6 Ver 1 01/2015

Aidapt Bathrooms Ltd, Lancots Lane, Sutton Oak, St Helens, WA9 3EX

Telephone: +44 (0) 1744 745 020 • Fax: +44 (0) 1744 745 001 • Web: www.aidapt.co.uk

Email: [email protected] • [email protected] • [email protected].uk

This manual suits for next models

Table of contents

Other aidapt Mobility Aid manuals

Popular Mobility Aid manuals by other brands

Alber

Alber Scalamobil iQ operating instructions

Ferno

Ferno CCT-PX user manual

HEPRO

HEPRO Gripo user manual

Otto Bock

Otto Bock Pheon 3R62 Instructions for use

NRS Healthcare

NRS Healthcare M11090 User instructions

Medline

Medline MDS86835DSHEC User Instructions & Warranty

Guldmann

Guldmann Twin Turner II user manual

Drive

Drive ROOMBA Operation manual

Gate

Gate Balder operating instructions

Decon wheel

Decon wheel TNS Notos Assembly instructions

ExoAtlet

ExoAtlet ExoAtlet-II user manual

Invacare

Invacare Storm Series parts catalog

Rhythm Healthcare

Rhythm Healthcare B3800F manual

AMF-BRUNS

AMF-BRUNS PROTEKTOR installation manual

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Instructions for use

Rhythm Healthcare

Rhythm Healthcare C500U Assembly and Fitting Instructions

Lumex

Lumex RJ4200A manual

Rebotec

Rebotec Jumbo user manual

aidapt VY428S Manual

Popular Mobility Aid manuals by other brands