AGTRON ART 160 User manual

Single and Dual Loop Rate & Blockage System

Operator’s Manual

MNRT02609 P a g e | 2Software Revision 2.13

MNRT02609 P a g e | 3Software Revision 2.13

1. Quick Start Guide

1. Turn on the ART 160/260

2. Set the Default Cal (this will set all calibrations back to the default settings)

Press RATE

Press MODE

Press CAL until the screen displays SET DEFAULT CAL?

Press and hold the OK button until the screen displays DEFAULT CAL SET!

All calibration settings are now reset to their default values.

3. Set the Test Speed (speed you will travel in the field)

Press RATE

Press MODE

Press CAL

The screen displays: TEST SPEED MPH

Press the UP or DOWN arrow keys to set the speed you will be seeding at (ex: 5.5 MPH)

You need a speed in order to set up the monitor using the Seed Rate Wizard

IMPORTANT! You must be seeding to perform a complete calibration.

4. Set up blockage monitoring

When Default Calibration is performed, a sensitivity value of 15 is set for each loop, if a blockage alarms while seeding and

there are no blockages decrease the sensitivity as necessary.

Press RATE

Press RATE again to select the loop you want to set up (with Dual Loop)

Each time you press RATE, Loop 1 (R1) and Loop 2 (R2) are switched on the top line of the display. The Loop shown on

the top line will be changed

Press CAL until you get to the SENSITIVITY screen

Press the UP arrow to increase the value and the Down arrow to decrease the value

Press RATE again and check for a blockage message

5. Set up the Seed Rate using the Seed Rate Wizard while seeding

Press RATE

Press RATE again to select the Loop you want to set up (with Dual Loop)

Each time you press RATE, Loop 1 (R1) and Loop 2 (R2) are switched on the top line of the display. The Loop shown on

the top line will be changed

Press CAL

The screen displays: SEEDRATE WIZARD PRESS THE OK KEY

Press OK

The screen displays: DESIRED SEEDRATE LB/AC

Press the UP or DOWN arrow keys to set how many LB/AC you want to seed (e.g. 120LBS)

(If you have seed and fertilizer in the same loop set the total LBS/AC for seed

and fertilizer together)

You must be on the RATE screen in order to hear alarms.

MNRT02609 P a g e | 4Software Revision 2.13

2. Flow Chart

MNRT02609 P a g e | 5Software Revision 2.13

Follow safety Instructions



Be sure to follow all safety instructions in your air seeder operator’s manual.

Read and Understand This Manual Before Operating This Machine.



Learn how to operate and service the machine correctly. Failure to do so could result in personal injury or equipment

damage. Agtron Enterprises Inc. will not accept any responsibility for any damage or malfunctions resulting from failure

to comply with the operator’s manual.



If you do not understand the information in this manual, or if you have any questions, contact Agtron Enterprises Inc.

Customer Service 1-800-667-0640.



This manual should be considered a permanent part of your machine and should remain with the machine when you sell

it.



The contents of this manual are the intellectual property of Agtron Enterprises Inc. All use and/or reproduction not

specifically authorized by Agtron Enterprises Inc. is prohibited.



All information, illustrations and specifications in this manual are based on the latest information available at the time of

publication. Agtron Enterprises Inc. reserves the right to make changes at any time without notice.



ATTENTION! Low battery or alternator voltage can cause system errors.

MNRT02609 P a g e | 6Software Revision 2.13

3. Table Of Contents

1. Quick Start Guide .......................................................................3

2. Flow Chart ...................................................................................4

3. Table Of Contents .......................................................................6

4. Introduction.................................................................................7

How Your Rate and Blockage Monitor Works.................................7

The User Interface.............................................................................7

5. Installation ...................................................................................9

Monitor Installation...........................................................................9

Cable Ties and Main Extension Cable Installation ...........................9

Seed Sensor and Sensor Loop Cable Installation............................10

Y-Cable Installation ........................................................................11

Figure 5-9. Installation Diagram 1..................................................12

Figure 5-10. Installation Diagram 2 (Less than 60 Sensors) ..........13

Figure 5-11. Installation Diagram 3 (More than 60 sensors) ..........14

Optional Sensor Installation............................................................15

Figure 5-12. Installation (Sensor Breakout Cable).........................19

Figure 5-13. Installation (ART Loop Terminator) .........................20

6. Setup...........................................................................................21

Optional Sensor Setup.....................................................................22

Speed Setup.....................................................................................22

Test Speed Setup.............................................................................23

Work Switch Setup .........................................................................23

Shaft Setup......................................................................................24

Fan Setup ........................................................................................25

Bin Setup.........................................................................................26

Meter Setup.....................................................................................26

7. Operation ...................................................................................27

Blockage .........................................................................................27

Rate Units........................................................................................27

Rate.................................................................................................28

High and Low Rate Alarms.............................................................28

Turning Loops On and Off..............................................................29

Speed Mode ....................................................................................29

Area Mode ......................................................................................29

Distance Mode ................................................................................29

Shaft Mode......................................................................................30

Fan Mode ........................................................................................30

Bin Mode ........................................................................................30

Meter Mode.....................................................................................30

Diagnostic Modes ...........................................................................31

8. Diagnostics and Troubleshooting.............................................32

Troubleshooting Table....................................................................32

9. Appendix....................................................................................37

Appendix A: Parts List....................................................................37

Appendix B: Optional Sensors........................................................38

Appendix C: Monitor Display Messages ........................................40

Appendix D: Seed Sensor Sensitivity Values .................................41

Appendix E: Conversion Factors ....................................................42

Appendix F: Default Calibration Values.........................................43

Appendix G: ART Toolbar Sensor Breakout Connector Pin-out....44

Appendix H: DB9 (9 Pin) Connector Pin-out .................................44

Appendix I: Deutsch DTM Connector Pin-out ..............................44

10. Notes ...........................................................................................45

11. Warranty....................................................................................46

Warranty Guidelines .......................................................................46

MNRT02609 P a g e | 7Software Revision 2.13

4. Introduction

With this monitor you can confirm your calibration for seed and

fertilizer rates, and detect blockages in up to 120 seed and 120

fertilizer runs. You can also monitor six additional tank and toolbar

sensors (shaft, bin, speed, fan, work switch) and three in-cab sensors

and switches (GPS, radar, work switch).

How Your Rate and Blockage Monitor Works

Single and Dual Loop Rate and Blockage Monitors use infrared seed

sensors to measure seed rate and check for blockages. The sensors

operate on a similar principle to that of a motion detector in a

security system. The Dual Loop system includes a second sensor

Loop so seed and fertilizer can be measured separately in double

shoot systems. In both systems, sensors are connected in a Loop

each communicating in turn and each including built-in diagnostics.

The system determines the number of sensors in a Loop

automatically. A maximum of 120 sensors can be connected in a

Loop.

Additional sensors for shafts, bin and fan monitoring can be added.

(Six for the Single Loop and nine for the Dual Loop.)

The User Interface

The user interface for Single and Dual Loop monitors includes a 16

character by two line display and seven buttons (PWR, RATE,

MODE, CAL, OK,).

The display, the backlit display will always show the currently

operating mode on the top line. The bottom line shows alarms and

rate information.

Figure 4-1

MNRT02609 P a g e | 8Software Revision 2.13

Abbreviations Used on Display

Display Buttons

Abbreviation

Meaning

KSD

Thousands of seeds

KPH

Kilometers per hour

MPH

Miles per hour

SAE

English/US

Kilograms

Hectares

Sensor loop

Pounds

Acres

Rate 1

Rate 2

RPM

Revolutions per minute

Key

Function

PWR

Press to turn power on and off

RATE

Press to toggle between R1 and R2 Rate

display; also used to go back to the

“home” screen

MODE

Press to cycle through modes of

operation

CAL

Press to enter a new calibration menu

Press to acknowledge alarms; or save

entered calibration values



Select high/low alarm values; Enter

calibration values

MNRT02609 P a g e | 9Software Revision 2.13

5. Installation

Monitor Installation

Mounting the Monitor

1. Screw the RAM Mount to the back of the monitor with

supplied M5 hex screws (Agtron Part# 450014004).

2. Attach base of RAM Mount to preferred location (mounting

hardware not included).

Power Cable

1. Connect the

red

wire directly to the positive battery terminal.

2. A fuse is not required.

3. Connect the

black

wire directly to the negative battery

terminal.

Do not connect to the cab. Not all tractor cabs are properly

grounded.

Cable Ties and Main Extension Cable Installation

Colored Cable Ties

The colored cable ties included in this kit are to assist in easy

installation and to differentiate between the two loops of sensors

1. Attach blue ties for all Loop 1 cables.

2. Attach yellow ties for all Loop 2 cables.

Power

Loop1

Loop 2

(Dual Loop only)

Tip:

Avoid connecting at starter terminals and on 24 volt systems be sure to connect

the monitor to the correct battery. It should be the one with its negative

terminal connected to the tractor chassis (ground). Connect the red (+) lead of

the monitor to the positive (+) terminal of that battery and the black (-) lead of

the monitor to the tractor chassis. Incorrect wiring could result in damage to

your monitor.

Figure 5-1

Figure 5-2

Figure 5-3

MNRT02609 P a g e | 10 Software Revision 2.13

Main Extension Cables

When making Extension Cable connections, make sure you align the

molded arrows. If they are difficult to push together, check the

condition of the pins. For each Loop (1 for Single; 2 for Dual):

1. Connect the cable from the Monitor to a 10ft or 20ft Main

Extension Cable inside the tractor.

2. Route the Main Extension Cable to the tractor hitch, allowing

extra for hitch movement.

Seed Sensor and Sensor Loop Cable Installation

1. Select a mounting location near the distributor.

2. Mount the Seed Sensors in the hose above the implement

chassis to protect the Seed Sensors and cables from field

debris damage.

The Sensor Loop Cables should not be stretched tight when

connected.

3. Secure the Seed Sensors in the hose using metal hose clamps

on each side (Agtron Part# 400TRHS16 not included).

4. Select a seed sensor on the far left of the machine to be

sensor #1. Leave the female plug of this sensor unplugged,

but connect the male plug to the sensor beside it. This will

be sensor #2.

5. Continue connecting sensor #2 to sensor #3 and so on, until

the manifold is all connected. Attach a Sensor Loop cable to

the male end of the last sensor on the first manifold.

6. Connect the male end of the Sensor Loop Cable to the

female end of the first sensor on the 2nd manifold. Continue

in this fashion until you reach the far right side of the

implement, leaving the male end on the last sensor

unplugged.

7. Using cable ties attach all cables to the frame of the

implement. Avoid pinch points such as wing lift and opener

lift points.

The Sensor Loop Cables should not be stretched tight

when connected.

Tip:

If necessary, apply heat to the hose

ends in order to fit the hose over the

sensor.

Sensors should be mounted on a

relatively straight part of the hose for

best performance.

Monitor head female Extension Cable male

Tip:

To help avoid electrical interference problems, create a figure eight shape

with excess cable before securing.

Figure 5-4

Figure 5-5

Figure 5-7

Figure 5-6

Other manuals for ART 160

This manual suits for next models

Table of contents

Other AGTRON Monitor manuals

AGTRON

AGTRON ART 160 User manual

Popular Monitor manuals by other brands

Linear Acoustic

Linear Acoustic LQ-1000 user guide

AOC

AOC I2579V user manual

Gateway

Gateway FPD1520 user guide

Furuno

Furuno Mu 120c Operator's manual

Asus

Asus VB171D - 17" LCD Monitor Service manual

Dell

Dell S2230MX Setting up

Philips

Philips 107C64 user manual

Dell

Dell S2409WFP user guide

EverFocus

EverFocus EN-7517E instruction manual

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Service manual

Dell

Dell Precision 7680 Connection guide

LG 50PM1M - - 50" Plasma Panel Service manual

Bosch

Bosch DDU 9 manual

Acer

Acer A231HL user manual

Philips

Philips 86BDL4152T user manual

NEC

NEC AccuSync LCD5V user manual

Emay

Emay SleepO2 user manual

IBM

IBM 6360 Product support manual