Agaro Grand User manual
MANUAL
Model: Grand
Item no - 33555
Professional Blender
W
a
r
r
a
n
t
y
2
YearS
W
a
r
r
a
n
t
y
ABOUT THE PRODUCT
CAUTION
Steam Cap Cup Cap
Mixing Cap
Cup Mat
Speed Contrd Knob
Start Switch
Base Bottom
Rubber Feet
Pulse Switch
Do not put metal objects such as knives, forks, spoons, etc.
into the cup
When cleaning, do not clean the knife directly by hand. If
you use cleaning tools, please pay attention to safety
The contents of the cup should not be too full. Do not
exceed two thirds of the capacity of the cup. Please close
the lid of the cup when using
Before starting, make sure the cup is on the base. It is
completely fixed on
Because of the high horsepower, please hold the cup
slightly when you start to use it
Be sure to cover the cup when using the stirring bar while
the motor is running
Whether the cup is placed on the table or not. Do not use
your hand to fetch food from that cup because the blade
is sharp and easy to cut
To pour food out, remove the cup from the frame
Be careful to touch the switch before and after start-up
Utensils cannot be immersed in water
CLEANING AND MAINTENANCE METHODS
FUNCTION INTRODUCTION
Do not put metal objects such as knives, forks, spoons, etc.
into the cup
When cleaning, do not clean the knife directly by hand. If
you use cleaning tools, please pay attention to safety
The contents of the cup should not be too full. Do not
exceed two thirds of the capacity of the cup. Please close
the lid of the cup when using
Before starting, make sure the cup is on the base. It is
completely fixed on
Because of the high horsepower, please hold the cup
slightly when you start to use it
Be sure to cover the cup when using the stirring bar while
the motor is running
Whether the cup is placed on the table or not. Do not use
your hand to fetch food from that cup because the blade
is sharp and easy to cut
To pour food out, remove the cup from the frame
Be careful to touch the switch before and after start-up
Utensils cannot be immersed in water
Always pull off the plug when cleaning and maintaining
Carefully scrub the cup body and lid with a sponge or
cloth and dry
Do not put your hand into the cup for cleaning
Wipe the rotating shaft and motor base with a dry
cloth (remember! Do not rinse with water)
When it is not easy to wipe, wipe it with neutral lotion, and
then wipe it with dry cloth until it is clean
Care should be taken when handling cutting
blades especially when removing blades from
containment cups, emptying containment cups,
and during cleaning
PULSE
CIRCUIT DIAGRAM
Start Switch
The switch is preset to “OFF ”before delivery.
Turn the switch to the “ON” position to start the product.
Turn the switch to the “OFF” position to stop the product.
Pulse Switch
The switch is preset to “OFF” before delivery.
Turn the switch to the “ON” position to run the product at
full speed.
If you release the switch, it will automatically return to the
“OFF” position.
Low/High Speed Switch
The switch is preset to “Low Speed” before delivery.
Turn the switch to the “Low Speed” position to run the
product at low speed.
Turn the switch to the “High Speed” position to run the
product at high speed
Wiring is subject to change without prior notice
MAIN TECHNICAL PARAMETERS
FAULT ANALYSI
Fault
Phenomenon
Indicator light
is not on
Indicator Light On
Product Inoperative
1.The power cord is not
plugged in.
2.The stirring cup and the
main engine are not
assembled properly.
1.Long working hours,
motor overheat
protection.
2.The machine itself is
out of order.
1.Wait an hour before
reusing.
2.Send to after-sales service
department.
1.Check the power cord to
make sure it is plugged in.
2.Make sure that the mixing
cup and the main
machine are installed
properly.
Cause Analysis Exclusion Methods
Note:
Above are common trouble analysis and troubleshooting methods. For other
troubles, please contact our customer service department, or go directly to
our designated repair point for repair. Do not dismantle and repair yourself.
Rated voltage: 220V-240V
Rated frequency: 50-60Hz
Rated power: 2000W
Rated capacity: 2.0L
NOTE
Professional Blender
Grand (Item No - 33555)
Scan - For Warranty Registration
(Must register within 30 days
from date of purchase to avail
3 MONTHS EXTENDED WARRANTY)
or visit: www.agarolifestyle.com/product-registration or visit: www.agarolifestyle.com/service
(Fill & submit the form if you are
facing any product related issues)
Scan - To File Complaint
• Please scan the QR CODE for product registration and avail “3 MONTHS
EXTENDED WARRANTY” on product
• Please preserve the invoice for product warranty claim. Customer purchasing
from online platforms needs to produce the Online Partner's Invoice copy to
claim the warranty
For any feedback or complain, you can also connect us at:
UNIVERSAL CORPORATION LIMITED, 4/1 Middleton Street, Sikkim Commerce
House, Kolkata-700071
Customer Care No: 9821-486-487
Product Name
Model
Name, Address &
Contact no of customer
Name, Address & Contact
no of dealer
Date of Purchase
Warranty Valid upto
: .................................................................................
: .................................................................................
: .................................................................................
.................................................................................
: .................................................................................
.................................................................................
: .................................................................................
: .................................................................................
LIMITED TWO YEARS WARRANTY
To checkout wide range of AGARO products,
please visit www.agarolifestyle.com
Home Appliances Electric Tooth Brush Massager
Hair Dryer Trimmer Healthcare
Music & Sound Luggage
& much more...
Treadmill
This manual suits for next models
1
Table of contents
Other Agaro Blender manuals
