AEG SU 86000 1L User manual

SANTO

ARCTIS

Integrierbare Unterbau-Kühl- und

Gefriergeräte

Réfrigérateurs et congélateurs sous-plan

à intégrer

Geïntegreerde onderbouwkoel- en

vriesapparaten

Integrated built-under refrigerators and

freezers

Integrerbara underbänk-kyl- och frysskåp

Työtason alle asennettavat jääkaapit ja

pakastimet

Frigoriferi e congelatori sottotavolo da

incasso

DMontageanweisung 2-10

FInstructions de montage 11-19

NMontage-aanwijzing 20-28

tInstallation instructions 29-37

SMonteringsanvisning 38-46

qAsennusohjeet 47-55

IIstruzioni di montaggio 56-63

Downloaded from Fridge-Manual.com Manuals

Grid preparation t

When changing the side at which the door opens, remove plug from

the mains.

Left door opening:

☞Remove the left side (A) of the grid cutting

it from the rear (see figure)

Right door opening:

☞Remove the right side (B) of the grid cutting

it from the rear (see figure)

Re-install the grid to the base of the appli-

ance by pushing on to the clasps (a) until

they click.

To reverse the opening direc-

tion of the door, proceed as

shown in the figures:

DO002/2

Reversing the door

The side at which the door opens can be changed from the right side

(as supplied) to the left side, if the installation site requires.

Downloaded from Fridge-Manual.com Manuals

Changing over the freezer compartment door

(not on all models)

Warning! After completion of

the door reversing operation,

check that the door gasket

adheres to the cabinet. If the

ambient temperature is cold

(i.e. in Winter), the gasket

may not fit perfectly to the

cabinet. In that case, wait for

the natural fitting of the

gasket or accelerate this pro-

cess by heating up the part

involved with a normal hair-

dryer on a low setting.

☞Open the freezer compartment door a

little way.

Using a small screwdriver, press the

spring in the opening of the lower door

bearing slightly upwards and take the

door bearing out complete with the

door.

☞

Downloaded from Fridge-Manual.com Manuals

Position the covering cap (M) on the

opposite side.

Turn the freezer compartment door

through 180° and fit the lower door

bearing into the lower bearing cavity

of the freezer compartment door.

Lift the freezer compartment door a

little way upwards, fit it into the

upper door bearing, and at the same

time insert the lower door bearing

into the square hole. Small upwards

and downwards adjustments of the

freezer compartment door will make

fitting easier.

☞

AEG43

Installation kit

1xA

1xB 2xC

600

550

min.

600

Building the appliance in under a worktop

The dimensions of the recessed

installation area must correspond

with those indicated in the figure.

☞

Downloaded from Fridge-Manual.com Manuals

Two cabinet securing brack-

ets are supplied with the

installation pack. They need

to be assembled onto the

cabinet prior to cabinet

being pushed into the

Kitchen aperture.

To fit these brackets remove

the two screws at the top

☞

Right hand

bracket

1/a

Left hand

bracket

Push the appliance into

place. The plug socket

necessary for connection

of the appliance to the

electricity supply should be

positioned, so that the

plug is not placed in the

recess.

To adjust the height pro-

ceed as follows:

Loosen or tighten the two

front feet.

☞

596

555

max

Li89 +

II52

If necessary, pads are supplied for the

rear feet to make sliding the appliance

in and out of the recess easier. To fit the

pads, press them onto the rear feet.

If required, the dimensions of these

pads can be reduced by breaking them

where marked.

☞

2/a

left and right hand front corners of the cabinet.

Position the two brackets as shown in the figure and replace the two

securing screws.

☞

The rear feet are adjusted by turning the screw in the front kick plate

to the left or right.

☞

Downloaded from Fridge-Manual.com Manuals

Screw appliance into place

☞The joint cover (B) is to be

assembled after having

installed the appliance in the

recess.

115°

Downloaded from Fridge-Manual.com Manuals

Mounting furniture door

clic

Downloaded from Fridge-Manual.com Manuals

11 =

Upper part of kitchen furniture panel

Lower part of kitchen furniture

panel

9/a

275 275

max 100

Downloaded from Fridge-Manual.com Manuals

Refit the covering strip.

☞

Downloaded from Fridge-Manual.com Manuals

Fitting the plinth

Important!

For the efficient operation of the appli-

ance, it is important that the original

ventilation grid is used.

• For an opening height dimension

A=820 mm and a plinth height

dimension a=100 mm, the plinth

may be fitted without adjustments.

The same applies to an opening

height dimension B=870 mm and a

plinth height dimension b=150 mm.

• For plinth heights greater than

a=100 mm, b=150 mm, a cut should

be made in the plinth, 580 mm wide,

in the centre of the appliance

position, leaving a remaining height

of a=100 mm, b=150 mm.

• Attach plinth to the kitchen units.

008

580

a=100

b=150

25-80

A=820

B=870

Important! The plinth must be positioned at a minimum distance of

25 mm from the door.

Downloaded from Fridge-Manual.com Manuals

Table of contents

Popular Refrigerator manuals by other brands

Bonnet Neve

Bonnet Neve SKYVIEW PLUS User instructions

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Instruction book

Sharp

Sharp SJ-BA31IEXW2-EU user manual

CORBERO

CORBERO CC2300MCW Instruction booklet

KitchenAid

KitchenAid 2205264 Use and care guide

Stengel

Stengel KU 1101 A++ user manual

NEFF

NEFF KI181 Series user manual

Hoshizaki

Hoshizaki Reach-In instruction manual

Amana

Amana ASD2524VES00 User instructions

BOMANN

BOMANN KGC 213 instruction manual

Danby

Danby DAR044A1SLDD Owner's use and care guide

Samsung

Samsung RF323TE user manual

Beko

Beko CSA31022 Instructions for use

IKEA

IKEA FROSTIG C 185 E manual

Electrolux

Electrolux ER 6821 D Instruction book

True

True TS-28 Specifications

Frigidaire

Frigidaire FSC23R5DW9 installation guide

Beko

Beko LSP4579W Instructions for use