Advantech PPC-L127T User manual

PPC-L127T

Intel®Celeron®M Processor-

based Fanless Panel PC with

12.1" TFT-LCD

User Manual

PPC-L127T User Manual ii

nal manufacturer reserves the right to make improvements to the products

described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmit-

ted in any form or by any means without the prior written permission of

the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer

assumes no responsibility for its use, nor for any infringements upon the

rights of third parties that may result from such use.

Acknowledgements

Award is a trademark of Award Software International, Inc.

Intel and Celeron are trademarks of Intel Corporation.

IBM, PC/AT, PS/2 and VGA are trademarks of International Business

Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows is a registered trademark of Microsoft Corp.

RTL is a trademark of Realtek Semiconductor Co., Ltd.

All other product names or trademarks are properties of their respective

owners.

For more information on this and other Advantech products, please visit

our websites at: http://www.advantech.com

http://www.advantech.com/ppc

For technical support and service, please visit our support website at:

http://support.advantech.com

This manual is for the PPC-L127T.

Part No. 2006L12700

1st Edition, Printed in Taiwan, December 2007

iii

FCC Class B

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential environment. This

equipment generates, uses and can radiate radio frequency energy. If not

installed and used in accordance with this user manual, it may cause

harmful interference to radio communications. Note that even when this

equipment is installed and used in accordance with this user manual, there

is still no guarantee that interference will not occur. If this equipment is

believed to be causing harmful interference to radio or television recep-

tion, this can be determined by turning the equipment on and off. If inter-

ference is occurring, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to a power outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Warning! Any changes or modifications made to the

equipment which are not expressly approved by

the relevant standards authority could void your

authority to operate the equipment.

PPC-L127T User Manual iv

Packing List

Before you begin installing your card, please make sure that the following

materials have been shipped:

• PPC-L127T series panel PC

• User manual

• Accessories for PPC-L127T

- Y-shaped adapter for PS/2 mouse and keyboard

- Warranty card

- DC plug-in housing (female) is connected on the AC/DC power

adapter

- Driver CD-ROM disc

- Mounting kits and packet of screws

If any of these items are missing or damaged, contact your distributor or

sales representative immediately.

Additional Information and Assistance

Step 1. Visit the Advantech web site at www.advantech.com where you

can find the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version, application

software, etc.)

• A complete description of the problem

• The exact wording of any error messages

Caution! Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equiv-

alent type recommended by the manufacturer.

Dispose of used batteries according to the man-

ufacturer's instructions.

Warning! 1. Input voltage rated 12 ~ 25 V, 4.5A max

2. Use a 3 V @ 195 mA lithium battery

3. Packing: please carry the unit with both

hands, handle with care

4. Maintenance: to properly maintain and clean

the surfaces, use only approved products or

clean with a dry applicator

5. CompactFlash: Turn off power before insert-

ing or removing CompactFlash storage card.

Contact information:

Our European representative:

Advantech Europe GmbH

Kolberger Straße 7

D-40599 Düsseldorf, Germany

Tel: 49-211-97477350

Fax: 49-211-97477300

PPC-L127T User Manual vi

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or let-

ting it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment

from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according

to the user manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE

THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR

ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE

EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY

REPLACED.REPLACE ONLY WITH THE SAME OR EQUIVALENT

TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED

BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUC-

TIONS.

The sound pressure level at the operator's position according to IEC 704-1:1982 is

no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-

tech disclaims all responsibility for the accuracy of any statements contained

herein.

vii

W i c h t i g e S i c h e r h e i s h i n w e i s e

1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie

Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch

zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht

zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen

oder Fallen könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit-

zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.

Es sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu

beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom

Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädi-

gung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten

in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-

lösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen

und von einer qualifizierten Servicestelle zu überprüfen:

a - Netzkabel oder Netzstecker sind beschädigt.

b - Flüssigkeit ist in das Gerät eingedrungen.

c - Das Gerät war Feuchtigkeit ausgesetzt.

d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert

oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batte-

rie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-

mahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des

Herstellers.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000

beträgt 70dB(A) oder weiger.

DISCLAIMER: This set of instructions is given according to IEC704-1.

Advantech disclaims all responsibility for the accuracy of any statements

contained herein.

Contents

Chapter 1 General Information ........................................2

1.1 Introduction ....................................................................... 2

1.2 General Specifications....................................................... 3

1.3 LCD Specifications ........................................................... 6

1.4 Dimensions........................................................................ 7

Figure 1.1:Dimensions of PPC-L127T ........................... 7

Chapter 2 System Setup...................................................10

2.1 A Quick Tour of the Panel PC ........................................ 10

Figure 2.1:Front view of PPC-L127T panel PC ........... 10

Figure 2.2:Rear view of Panel PC ................................ 11

Figure 2.3:Side view of the panel PC ........................... 11

Figure 2.4:Bottom view of the panel PC ...................... 12

2.2 Installation Procedures .................................................... 12

2.2.1 Connecting the power cord (Optional item: PS-DC19-

L60)12

2.2.2 Connecting the keyboard or mouse .............................. 12

2.2.3 Switching on the power ................................................ 12

Figure 2.5:Connect the power cord to the DC inlet...... 13

2.3 Running the BIOS Setup Program .................................. 13

2.4 Installing System Software.............................................. 14

2.4.1 Method 1: Use the Ethernet .......................................... 14

2.4.2 Method 2: Use the COM or parallel port...................... 14

2.4.3 Method 3: Use a CD-ROM........................................... 14

2.5 Installing the Drivers....................................................... 15

Chapter 3 Hardware Installation and Upgrading.........18

3.1 Introduction ..................................................................... 18

3.2 Installing the 2.5" Hard Disk Drive (HDD) .................... 18

Figure 3.1:Installing primary 2.5" HDD....................... 19

3.3 Installing the battery pack ............................................... 20

Figure 3.2:Installing the battery pack ........................... 20

Chapter 4 Jumper Settings and Connectors..................22

4.1 Jumpers and Connectors.................................................. 22

4.1.1 Setting jumpers ............................................................. 22

4.1.2 Jumpers and connectors................................................ 23

Table 4.1:Table 4.1: Jumpers and Connector functions23

PPC-L126 User Manual ii

4.1.3 Locating jumpers and connectors ................................. 24

Figure 4.1:Jumpers and Connectors on the PPC-L127T

motherboard24

4.2 CMOS Clear for External RTC (JP1) ............................. 25

Table 4.2:CMOS clear (J1)........................................... 25

4.2.1 COM1/COM2/COM3/COM4 pin 9 output setting

(JP2; JP3)26

Table 4.3:COM1/ COM2/COM3/COM4 pin 9 output set-

ting (JP2; JP3)26

4.3 VGA Interface................................................................. 26

4.3.1 LCD panel power setting .............................................. 26

Appendix A Pin Assignments .............................................28

A.1 Keyboard and PS/2 Mouse Connector (CN20)............... 28

Table A.1:Keyboard and mouse connector (CN20) ..... 28

A.2 USB port (CN12) ............................................................ 28

Table A.2:USB port (CN12)......................................... 28

A.3 COM1 RS-232 serial port (CN30) .................................. 28

Table A.3:COM1 RS-232 serial port (CN30)............... 28

A.4 COM2 (CN22)................................................................. 29

Table A.4:COM2 (CN22)............................................ 29

A.5 COM3 RS-232 serial port (CN31) .................................. 29

Table A.5:COM3 RS-232 serial port (CN31)............... 29

A.6 COM4 RS-232 serial port (CN23) .................................. 30

Table A.6:COM3 RS-232 serial port (CN23)............... 30

A.7 Parallel Port Connector (CN29) ...................................... 30

Table A.7:Parallel Port Connector (CN29)................... 30

A.8 VGA Connector (CN2) ................................................... 31

Table A.8:VGA connector (CN2)................................. 31

A.9 PCI/ISA Bus connector (Slot 1)...................................... 32

Figure A.1:PCI/ISA connector (Side View)................. 32

Table A.9:PCI/ISA pin assignments (Pins A and B).... 33

Table A.10:PCI/ISA pin assignments (Pins C and D).. 34

Table A.11:PCI/ISA pin assignments (Pins E and F)... 35

Table A.12:PCI/ISA pin assignments (Pins G and H).. 36

Table of contents

Other Advantech Touch Panel manuals

Advantech

Advantech IPPC-8151S Series User manual

Advantech

Advantech PPC-153 User manual

Advantech

Advantech PPC-3150 User manual

Advantech

Advantech PPC-120 User manual

Advantech

Advantech TPC-B610 User manual

Advantech

Advantech PPC-175T User manual

Advantech

Advantech PPC-6151C User manual

Advantech

Advantech TPC-1260 User manual

Advantech

Advantech TPC 40 Series User manual

Advantech

Advantech PPC-3150SW Installation and operation manual

Advantech

Advantech IPPC-9151G User manual

Advantech

Advantech PPC-315W TGL Installation and operation manual

Advantech

Advantech PPC-A84 User manual

Advantech

Advantech TPC-60S User manual

Advantech

Advantech TPC-1250H User manual

Advantech

Advantech PPC-112W Installation and operation manual

Advantech

Advantech PPC-4211W User manual

Advantech

Advantech PPC-3150-XE4BE Installation and operation manual

Advantech

Advantech TPC-100W Series User manual

Advantech

Advantech PPC-318W Installation and operation manual

Advantech

Advantech PPC-150T-RT User manual

Advantech

Advantech PPC-L128T User manual

Advantech

Advantech PPC-150 Series User manual

Advantech

Advantech PPC-3211SW Installation and operation manual

Popular Touch Panel manuals by other brands

FlowLine

FlowLine Data loop quick start

ALPEX

ALPEX AEx-8 P Series user manual

Ltech

Ltech E5S manual

Harman

Harman AMX MODERO S MSD-701-L2 quick start guide

Acnodes

Acnodes PC 1150 installation guide

AIS

AIS IP10IA99 series user guide

IBASE Technology

IBASE Technology ASTUT-152-RE1S user manual

YASKAWA

YASKAWA TP 610C manual

B&R

B&R Power Panel C Series user manual

Beijer Electronics

Beijer Electronics X2 control Hardware and installation manual

AXIOMTEK

AXIOMTEK GOT321W-521 user manual

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Operation manual

Qomo

Qomo QIT1386 user manual

DFI

DFI KS104-CD user manual

AMX

AMX AXP-PPC Dimensional drawing

Sartorius

Sartorius X3 PR 5410 operating manual

AMX

AMX Modero X Series quick start guide

B&R Industries

B&R Industries MAPPC900-ENG user manual