Advantech ADAM-6050W User manual

ADAM-6050W 18-channel Digital I/O Module

The ADAM-6050W is a high-density I/O module built-in a IEEE802.11b wireless LAN interface for seamless Ethernet

connectivity. It provides 12 digital input and 6 digital output channels with 5000VRMS Isolating protection. All of the

Digital Input channels support input latch function for important signal handling. Mean while, these DI channels allows

to be used as 1 KHz counter. Opposite to the intelligent DI functions, the Digital Output channels also support pulse

output function.

ADAM-6050W

Figure 1: ADAM-6050W 18-channel Digital I/O Module

ADAM-6050W Specification

Analog Input:

• Channel: 18

• I/O type: 12 DI & 6 DO

• Digital Input: Dry Contact:

Logic level 0: Close to GND

Logic level 1: Open

Wet Contact:

Logic level 0: +3 Vmax Logic level 1: +10 to 30 VDC

• Digital Output:Open Collector to 30 V, 200 mA max. load

•Communication: Wireless LAN IEEE802.11b

•Optical Isolation: 5000VRMS

•Power Consumption: 2 W (Typical)

Application Wiring

Figure 2: ADAM-6050W Digital Input (Wet Contact) Wiring

Figure 3: ADAM-6050W Digital Input (Dry Contact) Wiring

Figure 4: ADAM-6050W Digital Output Wiring

System Architecture

ADAM-6050W Configuration

Network Configuration

Step 1 : Please open theADAM-5000TCP-6000 utility software. The utility software will automatically

scan the ADAM-6000 modules. Please wait for the ADAM-6050W being found by utility software.

Step 2 : Please go the “Network” page to change the IP address/Subnet Address/Default Gateway of

ADAM-6050W module to be compatible with user’s existing network and set the host idle time out value

(the ADAM-6000 module can only accept 8 connection from host station. Any host station doesn’t request

the communication with thisADAM-6000 module over the time out setting, the connection of this host

station will be released for the other stations).

press “Apply” to download the new IP address to ADAM-6050W module (the default password for the

changing configuration is “00000000”).

Step 3 : Re-configuring the IP address of the configuration PC to be the original setting (compatible with

user’s existing network) then re-start the utility software. The software will automatically search the

ADAM-6050W module again.

Step 4 : Go to the “Wireless” page to set the wireless LAN configuration.

Please set the wireless LAN mode to be “Infrastructure” or “Adhoc” based on exact system architecture.

Please assign the SSID for the specific wirelessAP to be connected with ADAM-6000W modules. User

can place “ANY” key to let theADAM-6000W modules to automatically search the existing wireless AP. Or

key in the specific SSID to assign the dedicated AP (strongly recommending to set up the dedicated SSID,

it can guarantee the communication ofADAM-6000W modules to be stable)

For assigning the dedicated wireless LAN AP, user can use the site survey function to check the existing

AP in connection environment. Please go to the “Site Survey” page.

Press “Scan” bottom to search the existing AP.

Selecting the AP in the searching result table.

Press “Apply” bottom to accept the AP to finish the set up action.

Please select the region for your area.

Setting the used channel, the channel number must be included in the channel segment of your region.

Please select the basic rate for the communication bandwidth.

Table of contents

Other Advantech I/O System manuals

Advantech

Advantech I/O Module 5000 Series User manual

Advantech

Advantech PCI-1758UDIO Installation and operation manual

Advantech

Advantech ADAM-6300 Series User manual

Advantech

Advantech PCM-3730 User manual

Advantech

Advantech PCL-720 User manual

Advantech

Advantech WISE-4000 Series User manual

Advantech

Advantech PCM-3724 Installation and operation manual

Advantech

Advantech WISE-4210 Series Installation and operation manual

Advantech

Advantech PCI-1713 User manual

Advantech

Advantech ADAM-3600-A1F User manual

Advantech

Advantech WISE-4060 Installation and operation manual

Advantech

Advantech MIC-75G20 Installation and operation manual

Advantech

Advantech PCL-813 User manual

Advantech

Advantech USB-4751 User manual

Advantech

Advantech WISE-4050 User manual

Advantech

Advantech PCL-722 User manual

Advantech

Advantech ECU-P1702 Installation and operation manual

Advantech

Advantech USB-5801 User manual

Advantech

Advantech UNO-2000-LKAE User manual

Advantech

Advantech WISE-4610 Series User manual

Advantech

Advantech PCIE-1756H User manual

Advantech

Advantech AMAX-5000 Series User manual

Advantech

Advantech APAX-5000 Series User manual

Advantech

Advantech USB-582 Installation and operation manual

Popular I/O System manuals by other brands

WAGO

WAGO 750-344 manual

Teknim

Teknim TWM-1887 Installation & user manual

Intelligent Appliance

Intelligent Appliance IA-2662-E user manual

BERGHOF

BERGHOF ECC DIO 16/16 User handbook

Festo

Festo CP-E08-M12-CL manual

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 user guide

Hitachi

Hitachi HX-RIO3 Series user manual

NUUO

NUUO SCB-A08 user manual

M-system

M-system R3Y-RS8 instruction manual

jablotron

jablotron JB-110N user manual

Omron

Omron SYSMAC C200H Operation guide

DOLD

DOLD SAFEMASTER M Safety Technique

ABB

ABB OPT-MF-001 user manual

Omron

Omron SYSMAC C2000H Operation guide

Helmholz

Helmholz TB20 manual

ICP DAS USA

ICP DAS USA tM-AD2 quick start

Automationdirect.com

Automationdirect.com DL305 manual

WAGO

WAGO I/O-SYSTEM 750 manual