ADTRAN SMART/RG SR516ac User manual
SR516ac
Quick Start Guide
Installation
1. Connect one end of the included phone cable to the DSL port on the gateway and connect the other end to the
wall jack.
2. Connect one end of an Ethernet cable to a LAN port of the gateway and connect the other end to your PC.
3. Plug the power adapter into the wall outlet and connect the other end of it to the Power port of the gateway.
4. Turn on the unit by pressing the On/Off button on the left side of the gateway.
Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to
complete before you can begin using your Internet applications (browser, email, etc.).
Notes:
lIf you use 3G WAN service, connect the 3G USB data card to the USB port of the gateway. If you use the Ethernet
uplink, connect to the WAN port with an Ethernet cable.
lYou cannot use the xDSL uplink, 3G WAN service, and Ethernet uplink at the same time.
If you are unable to connect to the Internet, confirm that all connections are in place and the gateway is turned on.
3
LED Indicators
The LEDs on the front of the SR516ac gateway can help you
understand the current state of your adapter.
Legend: White White blinking Red Green Green blinking
LED Action Explanation
All LEDs
except
those
listed below
Feature enabled &/or working correctly
Data being transferred
POWER Device in CFE mode
Device powered on and ready for use
WAN WAN connection active
LAN LAN connection active
Data being transferred
Quick Gateway Configuration
Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small
round hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into
the hole, press the button for 1 second, and then release the button. The system reboots and returns to the factory
defaults.
Logging in to your gateway
To change the settings on your gateway, you must log in to the gateway's interface. Make sure that you have completed
the steps in "Installation" before you begin.
1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.
2. Enter the factory default credentials shown below and click OK.
User Name: admin Password: admin
Note: Your service provider may use other settings. Contact your provider for details.
5
Configuring the WAN manually
If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer 2 Interface and WAN Service
sections of the SmartRG SR516ac Gateway User Manual to manually establish a connection.
WiFi Setup
Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow
the instructions for the applicable method. The default settings work for most situations.
1. In the left menu, click Wireless and then click 2.4 GHz Band or 5 GHz Band. The fields are the same for both
options. The wireless radio is enabled by default.
2. If desired, in the SSID field, enter the network name to which you want your client devices connected.
Continue with the steps in the method you prefer.
3. Continue with the steps for the method you prefer.
7
WPS Method
If the device you wish to connect to the Internet via your gateway supports the WPS secure Wi-Fi connection method,
follow these steps.
1. In the left navigation bar, click Wireless, click the band that you want to configure, and then click Security.
2. In the Enable WPS field, make sure that Enabled is selected, and then click Apply/Save to save your change.
3. On the left side of the gateway:
a. Activate the desired band by pressing 2.4 GHz or 5 GHz briefly on the rocker switch.
b. Activate WPS by pressing the desired band button and holding it down for 7 seconds.
4. Within 2 minutes, activate WPS on the 3rd party device to which you wish to connect. The device may have a
push button on its exterior that you can press, or a clickable button on a software interface. To learn how to use
the WPS feature on your client device, refer to its documentation.
Your device should now be connected to your gateway wirelessly using WPS. If you encounter problems with the WPS
setup such as connection failure, refer to your client device for further instructions.
9
Manual Method
Set up your gateway’s parameters first, then follow these steps.
1. In the left menu, click Wireless, the band that you want to configure, and then click Security.
2. Scroll down to the Manual Setup AP section.
3. If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You
will need this ID for step 8.
4. Select the desired Network Authentication. Make sure that the host devices you intend to use support the
selected authentication type.
Other manuals for SMART/RG SR516ac
1
Table of contents
Other ADTRAN Gateway manuals
ADTRAN
ADTRAN Total Access 900 Series Manual
ADTRAN
ADTRAN SMART/RG SR555ac User manual
ADTRAN
ADTRAN 424RG User manual
ADTRAN
ADTRAN SMART/RG SR501 User manual
ADTRAN
ADTRAN SMART/RG SR501n User manual
ADTRAN
ADTRAN NetVanta 644 User manual
ADTRAN
ADTRAN 324RG User manual
ADTRAN
ADTRAN Total Access 916 Manual
ADTRAN
ADTRAN Total Access 912 User manual
ADTRAN
ADTRAN 7310-8 User manual
ADTRAN
ADTRAN 17600072F1S User manual
ADTRAN
ADTRAN NetVanta 644 User manual
ADTRAN
ADTRAN 324RG User manual
ADTRAN
ADTRAN SR700ac User manual
ADTRAN
ADTRAN NetVanta 6240 Series User manual
ADTRAN
ADTRAN 8612 User manual
ADTRAN
ADTRAN 6304W User manual
ADTRAN
ADTRAN SDX810-RG User manual
ADTRAN
ADTRAN 7310-8 User manual
ADTRAN
ADTRAN 434 RG User manual
Popular Gateway manuals by other brands
LST
LST M500RFE-AS Specification sheet
Kinnex
Kinnex Media Gateway quick start guide
2N Telekomunikace
2N Telekomunikace 2N StarGate user manual
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Original instructions
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE user guide
Telsey
Telsey CPVA 500 - SIP Technical manual
