Adexa ORBITRAC User manual
ORBITRAC
Owner’s Manual
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 1
SAFETY INSTRUCTIONS ------------------------------------------------------------- 2
PARTS LIST ------------------------------------------------------------------------------- 3
HARDWARE PACKING LIST --------------------------------------------------------- 5
TOOLS -------------------------------------------------------------------------------------- 6
OVERVIEW DRAWING -----------------------------------------------------------------7
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 8
OPERATING THE COMPUTER ------------------------------------------------------ 13
ADJUSTMENTS -------------------------------------------------------------------------- 14
MAINTENANCE -------------------------------------------------------------------------- 15
TROUBLESHOOTING ------------------------------------------------------------------ 15
WARM UPAND COOL DOWN ROUTINE -----------------------------------------16
2
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this equipment: Read all instructions before using this
equipment.
1. Read all the instructions in this manual and do warm up exercises before using this
equipment.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every
position of the body is necessary. Refer to Warm Up and Cool Down Routine page.
After exercise, relaxation of the body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
6. Be careful when step on or leave the pedal always hold the handlebars first. Make the
pedal at your side at the lowest position, step on the pedal, and stride over the main
frame then step on the other pedal. When using, please hold the handlebar by hands,
make the pedals running smoothly by push or pull handlebars, then run the equipment
regularly by cooperation of hands and feet. After exercise, please also make one
pedal at the lowest position and leave your foot on the higher pedal first and then
another.
7. Do not use the equipment outdoors.
8. This equipment is for household use only.
9. Only one person should be on the equipment while in use.
10. Keep children and pets away from the equipment while in use. This machine is
designed for adults only. The minimum free space required for safe operation is not
less than two meters.
11. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
12. The maximum weight capacity for this product is 100kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.
3
PARTS LIST
No.
Description
Qty
No.
Description
Qty
001
Handrail Arm End Cap Ø25x1.5
6
029
Flange Nut M10x1
2
002
Handrail Arm Foam Grip
Ø32xØ23x260
2
030
Eyebolt M6x36
2
003
Right Handrail Arm Ø25x1.8
1
031
Tension Bracket
2
004
Left Handrail Arm Ø25x1.8
1
032
Nut Cap S13
2
005
Handrail Arm Plastic Bushing
Ø28.5xØ25.4x84
4
033
Nut M6
2
006
Handrail Arm Height Adjustment
Knob
2
034
Main Frame
1
007
Bolt M10x18
2
035
Stabilizer End Cap Ø50
4
008
Spring Washer Ø18xØ10x2
2
036
Nylon Nut M6
2
009
Washer Ø28xØ16.2x4xB5
2
037
Transport Wheel Ø23xØ6x32
2
010
Powder Metal Bushing
Ø24.8xØ16x14
10
038
Bolt M6x48
2
011
Washer Ø28xØ16x1
1
039
Spring Washer Ø20xØ13x2
2
012
Rotation Rod
1
040
Nylon Nut for right Crank
B0.5x20
1
013
Left Handrail
1
041
Chain Pulley with Crank
1/4”/Ø205x2.6
1
014
Right Handrail
1
042
Nut Cap S16
4
015
Handlebar End Cap Ø32x1.5
2
043
Nylon Nut for left Crank B0.5x20
1
016
Fan Wheel
1
044
Computer XLG-203
1
017
Fan Wheel Axle
1
045
Tension Control Knob
1
018
Hexagon Nut M10x1
5
046
Bolt for left Crank Ø16x89xL23
1
019
Sensor
1
047
Cap Nut M10
4
020
Bolt M10x45
4
048
Curve Washer
Ø10x1.5xØ25xR28
4
021L
Left Foot Pedal 345x146x40
1
049
Bolt M10x57
4
021R
Right Foot Pedal 345x146x40
1
050
Front Stabilizer Ø50x1.5x470
1
022
Bolt for right Crank Ø16x89xL23
1
051
Rear Stabilizer Ø50x1.5x470
1
023
Foot Bar
2
052
Washer Ø40xØ24x3
1
024
Chain
1
053
Notched Bearing Nut 15/16”
1
025
Bolt M10x55
2
054
Bearing Cup
2
026
Powder Metal Bushing
Ø14xØ10x10
4
055
Bearing
2
027
Square End Cap (30x30)
2
056
Slotted Bearing Nut 7/8”
1
028
Nylon Nut M10xL9
6
057
Washer Ø34.5xØ23x2.5
1
4
PARTS LIST
No.
Description
Qty
No.
Description
Qty
058
Hexagon Nut 7/8”
1
064
Screw ST4.8x40
7
059
Right Cover
1
065
Screw ST4.8x15
1
060
Left Cover
1
066
Spring Ø10x1.8x32
1
061
Strap
1
067
Nut Cap S18
2
062
Cover Cap 86x65x1.5
2
068
Wave Washer Ø28xØ16x0.3
2
063
Phillips Self Tapping Screw
ST4.8x20
2
5
HARDWARE PACKING LIST
(7) Bolt M10x18
2 PCS
(8) Spring Washer
Ø18xØ10x2
2 PCS
(9) Washer
Ø28xØ16.2x4xB5
2 PCS
(20) Bolt M10x45
4 PCS
(12) Rotation Rod
1 PC
(28) Nylon Nut M10xL9
4 PCS
(32) Nut Cap S13
2 PCS
(47) Cap Nut M10
4 PCS
(49) Bolt M10x57
4 PCS
(48) Curve Washer
Ø10x1.5xØ25xR28
4 PCS
(67) Nut Cap S18
2 PCS
(42) Nut Cap S16
4 PCS
(11) Washer Ø28xØ16x1
1 PC
(22) Bolt for right Crank
Ø16x89xL23, 1 PC
(39) Spring Washer
Ø20xØ13x2, 1 PC
(40) Nylon Nut for right
Crank B0.5x20, 1 PC
(68) Wave Washer
Ø28xØ16x0.3, 1 PC
(39) Spring Washer
Ø20xØ13x2, 1 PC
(43) Nylon Nut for left
Crank B0.5x20, 1 PC
(46) Bolt for left Crank
Ø16x89xL23, 1 PC
(68) Wave Washer
Ø28xØ16x0.3, 1 PC
6
TOOLS
Allen Wrench 6mm
2 PCS
Allen Wrench 8mm
1 PC
Multi Hex Tool S19, S10, S13, S17
1 PC
7
OVERVIEW DRAWING
8
ASSEMBLY INSTRUCTIONS
1. Front and Rear Stabilizers Installation
Position the Front Stabilizer (50) in front of Main Frame (34) and align bolt holes.
Attach the Front Stabilizer (50) onto the front curve of the Main Frame (34) with two M10
Cap Nuts (47), two Ø10x1.5xØ25xR28 Curve Washers (48), and two M10x57 Bolts (49).
Tighten nuts with the Multi Hex Tool provided.
Position the Rear Stabilizer (51) behind the Main Frame (34) and align bolt holes.
Attach the Rear Stabilizer (51) onto the rear curve of the Main Frame (34) with two M10 Cap
Nuts (47), two Ø10x1.5xØ25xR28 Curve Washers (48), and two M10x57 Bolts (49).
Tighten nuts with the Multi Hex Tool provided.
Hardware:
4 Cap Nuts (M10)
4 Curve Washers
(Ø10x1.5xØ25xR28)
4 Bolts (M10x57)
Tool:
Multi Hex Tool S19, S10, S13, S17
9
2. Left/Right Handrails and Foot Bars Installation
Place the Rotation Rod (12) into the hole of the Main Frame (34). Slide the Left/Right
Handrails (13, 14) onto the Rotation Rod (12) and secure in place with two M10x18 Bolts (7),
two Ø18xØ10x2 Spring Washers (8), two Ø28xØ16.2x4xB5 Washers (9), and one
Ø28xØ16x1 Washer (11). Tighten bolts with two 6mm Allen Wrenches provided.
Attach the right Foot Bar (23) onto the right Crank (41) with one Ø16x89xL23 Bolt for right
Crank (22), one Ø28xØ16x0.3 Wave Washer (68), one Ø20xØ13x2 Spring Washer (39),
and one B0.5x20 Nylon Nut for right Crank (40). Tighten bolt and nylon nut with one 8mm
Allen Wrench and Multi Hex Tool provided.
Install a S18 Nut Cap (67) onto the B0.5x20 Nylon Nut for right Crank (40).
2 Allen Wrenches 6mm
Allen Wrench 8mm
Tool:
Multi Hex Tool S19, S10, S13, S17
Table of contents
Popular Elliptical Trainer manuals by other brands
Bonn Germany
Bonn Germany Concept 2.2 user manual
Precor
Precor Resolute RSL 620 Assembly guide
NordicTrack
NordicTrack E 9.2 Elliptical HASZNALATI UTASITAS
Vision Fitness
Vision Fitness X6600iNetTV Assembly guide
Matrix
Matrix MX-A5x owner's manual
SportsArt Fitness
SportsArt Fitness ECO-NATURAL Elite E874 owner's manual
