Acolyte EH50 User manual

EH50 Pendant

Installation manual

Please Read instructions fully prior to assembly

•These products may represent a potential shock or fire hazard if

improperly installed. Products should be installed in accordance with

these instructions and current electrical codes

•To avoid electrical shock, disconnect or disable power at the source

prior to installation or maintenance.

•To avoid electrical shock, use only with 12v or 24v DC hardwire or

plug in power supply. Factory warranty will be void if used otherwise

•To avoid product failure, pair the correct voltage power supply to

the correct voltage of the Ribbonlyte e.g., 24v Ribbonlyte with a 24v

power supply. Factory warranty will be void if used otherwise

•Do not use if there is any damage to the Ribbonlyte or to the power

Cord’s insulation. Inspect periodically.

•Ensure proper gauge wires are installed between Power Supplies,

Controls & Ribbonlyte to avoid voltage drop. (Please refer to cable chart)

Instructions

Step 1- Remove all fixtures from Packaging

Step2 –group fixtures into the assembled lengths according to the labelling.

Step 3 - working on assembling one length at a time split the fixtures in two as

shown.

Step 4 –Install the Hanging kits every 1.2m , slide square bolts into the top Housing

slots as shown ensuring they are all positioned approximately 1.2m apart

Step 5- screw both hanging couplers to the bolts and ensure suspension wire hangs

correctly.

Step 6 –slide the lens back and Install the connecting coupling bars into the upper

and lower part of the fixtures as shown and secure the Grub screws using an allen

key.

Lower part of fixture use upper part of fixture use

B connecting couplers A connecting couplers

Step 7 –with assistance clip the upper and lower fitting together by applying slight

pressure until it clicks into position, ensure all wires are within the fitting.

Step 8 –connect the two driver supply connectors together between each

connected fitting as shown.

Step 9 –Assemble the upper fixtures together and lock with the grub screws as

shown.

Step 10 –Assemble the lower fixtures together and lock with the grub screws as

shown.

Step 11 –slide the lens back in to position

Trim the lens using a stanley knife as required

Step 12 –using the supplied grey silicone, seal over the joints to prevent any light

leak and wipe clean with a lint free cloth.

Step 13 –position and secure the endcaps using the 4 supplied allen key screws.

Step 14 –suspend fitting from the ceiling and connect the power cord to the ceiling

rose.

Step 15 –repeat steps 1-14 for each fitting.

Angled connections

Step 1 –install the angled connection using connecting couplers labelled as shown

on the first fitting and secure with the grub screws .

Step 2 –Slide the two fittings together and secure the grub screws on the second

fitting

Step 3 –use the grey silicone to seal the joint to prevent light leak.

VOLTAGE DROP CHARTS

For best performance and lumen output, ensure proper wire gauge is installed to compensate for voltage drop of

low voltage circuits.

Example: 12V Voltage Drop & Wire Length Distance Chart

Wire

Gauge

10 W

.83 A

20 W

1.7 A

30 W

2.5 A

40 W

3.3 A

50 W

2.1 A

60 W

4.2 A

18 AWG

34 ft.

17 ft.

11 ft.

8 ft.

6 ft.

5 ft.

16 AWG

54 ft.

27 ft.

18 ft.

13 ft.

10 ft.

9 ft.

14 AWG

86 ft.

43 ft.

29 ft.

21 ft.

17 ft.

14 ft.

12 AWG

134 ft.

68 ft.

45 ft.

34 ft.

27 ft.

22 ft.

10 AWG

199 ft.

99 ft.

66 ft.

49 ft.

39 ft.

33 ft.

1Determine load size. Let’s assume load is 55W Round up to the nearest load.

2Determine distance from driver to load. Let’s assume the distance is 20ft

3 It’s Recommended to install 12AWG to eliminate excess voltage drop

12V Voltage Drop & Wire Length Distance Chart

Wire

Gauge

10 W

.83 A

20 W

1.7 A

30 W

2.5 A

40 W

3.3 A

50 W

2.1 A

60 W

4.2 A

18 AWG

34 ft.

17 ft.

11 ft.

8 ft.

6 ft.

5 ft.

16 AWG

54 ft.

27 ft.

18 ft.

13 ft.

10 ft.

9 ft.

14 AWG

86 ft.

43 ft.

29 ft.

21 ft.

17 ft.

14 ft.

12 AWG

134 ft.

68 ft.

45 ft.

34 ft.

27 ft.

22 ft.

10 AWG

199 ft.

99 ft.

66 ft.

49 ft.

39 ft.

33 ft.

24V Voltage Drop & Wire Length Distance Chart

Wire

Gauge

10 W

.42 A

20 W

.83 A

30 W

1.3 A

40 W

1.7 A

50 W

2.1 A

60 W

2.5 A

70 W

2.9 A

80 W

3.3 A

100 W

4. 2 A

18 AWG

134 ft.

68 ft.

45 ft.

33 ft.

27 ft.

22 ft.

19 ft.

17 ft.

14 ft.

16 AWG

215 ft.

109 ft.

72 ft.

54 ft.

43 ft.

36 ft.

31 ft.

27 ft.

22 ft.

14 AWG

345 ft.

174 ft.

115 ft.

86 ft.

69 ft.

57 ft.

49 ft.

43 ft.

36 ft.

12 AWG

539 ft.

272 ft.

181 ft.

135 ft.

108 ft.

90 ft.

77 ft.

68 ft.

56 ft.

10 AWG

784 ft.

397 ft.

263 ft.

197 ft.

158 ft.

131 ft.

112 ft.

98 ft.

82 ft.

Other Acolyte Lighting Equipment manuals

Acolyte

Acolyte NEONLYTE User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions