ABB Relion 615 series User manual
Relion® Protection and Control
615 series
DNP3 Communication Protocol Manual
Document ID: 1MRS756709
Issued: 2012-05-11
Revision: D
Product version: 4.0
© Copyright 2012 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third
party, nor used for any unauthorized purpose.
The software or hardware described in this document is furnished under a license
and may be used, copied, or disclosed only in accordance with the terms of such
license.
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
http://www.abb.com/substationautomation
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept
or product description and are not to be deemed as a statement of guaranteed
properties. All persons responsible for applying the equipment addressed in this
manual must satisfy themselves that each intended application is suitable and
acceptable, including that any applicable safety or other operational requirements
are complied with. In particular, any risks in applications where a system failure and/
or product failure would create a risk for harm to property or persons (including but
not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby
requested to ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested
to notify the manufacturer. Other than under explicit contractual commitments, in
no event shall ABB be responsible or liable for any loss or damage resulting from
the use of this manual or the application of the equipment.
Conformity
This product complies with the directive of the Council of the European
Communities on the approximation of the laws of the Member States relating to
electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning
electrical equipment for use within specified voltage limits (Low-voltage directive
2006/95/EC). This conformity is the result of tests conducted by ABB in
accordance with the product standards EN 50263 and EN 60255-26 for the EMC
directive, and with the product standards EN 60255-1 and EN 60255-27 for the low
voltage directive. The product is designed in accordance with the international
standards of the IEC 60255 series.
Table of contents
Section 1 Introduction.......................................................................3
This manual........................................................................................3
Intended audience..............................................................................3
Product documentation.......................................................................3
Product documentation set............................................................3
Document revision history.............................................................4
Related documentation..................................................................4
Symbols and conventions...................................................................5
Symbols.........................................................................................5
Document conventions..................................................................5
Section 2 DNP3 overview.................................................................7
DNP3 standard...................................................................................7
Documentation...................................................................................9
Section 3 Vendor-specific implementation.....................................11
DNP3 link modes..............................................................................11
DNP3 data objects.......................................................................11
DNP3 serial link mode.................................................................11
DNP3 TCP/IP mode....................................................................11
DNP3 point list..................................................................................12
Binary input points.......................................................................12
Binary output status points and control relay output blocks........12
Analog inputs...............................................................................14
Analog data scaling................................................................15
DNP points.......................................................................................16
Point configuration.......................................................................16
Class assignment........................................................................16
Accessing non-protocol mapped data.........................................17
Section 4 DNP3 parameters...........................................................19
Parameter descriptions.....................................................................19
Parameter list...................................................................................22
Section 5 Glossary.........................................................................25
Table of contents
615 series 1
Communication Protocol Manual
2
Section 1 Introduction
1.1 This manual
The communication protocol manual describes a communication protocol
supported by the IED. The manual concentrates on vendor-specific implementations.
1.2 Intended audience
This manual addresses the communication system engineer or system integrator
responsible for pre-engineering and engineering for communication setup in a
substation from an IED perspective.
The system engineer or system integrator must have a basic knowledge of
communication in protection and control systems and thorough knowledge of the
specific communication protocol.
1.3 Product documentation
1.3.1 Product documentation set
The application manual contains application descriptions and setting guidelines
sorted per function. The manual can be used to find out when and for what purpose
a typical protection function can be used. The manual can also be used when
calculating settings.
The communication protocol manual describes a communication protocol
supported by the IED. The manual concentrates on vendor-specific implementations.
The engineering guide provides information for IEC 61850 engineering of the 615
series protection IEDs with PCM600 and IET600. This guide concentrates
especially on the configuration of GOOSE communication with these tools. The
guide can be used as a technical reference during the engineering phase,
installation and commissioning phase, and during normal service. For more details
on tool usage, see the PCM600 documentation.
The engineering manual contains instructions on how to engineer the IEDs using
the different tools in PCM600. The manual provides instructions on how to set up a
PCM600 project and insert IEDs to the project structure. The manual also
recommends a sequence for engineering of protection and control functions, LHMI
1MRS756709 D Section 1
Introduction
615 series 3
Communication Protocol Manual
functions as well as communication engineering for IEC 61850 and other
supported protocols.
The installation manual contains instructions on how to install the IED. The
manual provides procedures for mechanical and electrical installation. The chapters
are organized in chronological order in which the IED should be installed.
The operation manual contains instructions on how to operate the IED once it has
been commissioned. The manual provides instructions for monitoring, controlling
and setting the IED. The manual also describes how to identify disturbances and
how to view calculated and measured power grid data to determine the cause of a
fault.
The point list manual describes the outlook and properties of the data points
specific to the IED. The manual should be used in conjunction with the
corresponding communication protocol manual.
The technical manual contains application and functionality descriptions and lists
function blocks, logic diagrams, input and output signals, setting parameters and
technical data sorted per function. The manual can be used as a technical reference
during the engineering phase, installation and commissioning phase, and during
normal service.
1.3.2 Document revision history
Document revision/date Product series version History
A/2009-03-04 2.0 First release
B/2009-07-03 2.0 Content updated
C/2010-06-11 3.0 Content updated to correspond to the
product series version
D/2012-05-11 4.0 Content updated to correspond to the
product series version
Download the latest documents from the ABB Web site
http://www.abb.com/substationautomation.
1.3.3 Related documentation
Product-specific point list manuals and other product series- and product-specific
manuals can be downloaded from the ABB Web site
http://www.abb.com/substationautomation.
Section 1 1MRS756709 D
Introduction
4615 series
Communication Protocol Manual
Other manuals for Relion 615 series
41
Table of contents
Other ABB Relay manuals
ABB
ABB ITH-T Series Guide
ABB
ABB ELR48P User manual
ABB
ABB Relion 630 Series User manual
ABB
ABB RELION REF615R User manual
ABB
ABB SPAJ 111 C User manual
ABB
ABB TF42 User manual
ABB
ABB Relion REX610 User manual
ABB
ABB REJ 525 User manual
ABB
ABB REU 610 Product manual
ABB
ABB Busch-Wachter 6812U-101-500 User manual
