ABB Relion REB500 User manual
RELION® REB500
Distributed busbar protection REB500
Version 8.3 IEC
Communication protocol manual
IEC60870-5-103
a
=
I
;
D
e
-
a
=
I
;
D
e
-
Document ID: 1MRK 511 451-UEN
Issued: May 2019
Revision: B
Product version: 8.3
© Copyright 2019 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third party, nor
used for any unauthorized purpose.
The software and hardware described in this document is furnished under a license and may
be used or disclosed only in accordance with the terms of such license.
This product includes software developed by the OpenSSL Project for use in theOpenSSL
Toolkit. (http://www.openssl.org/) This product includes cryptographicsoftware written/
developed by: Eric Young ([email protected]) and Tim Hudson([email protected]).
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or product names
mentioned in this document may be trademarks or registered trademarks of their respective
holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or product
description and are not to be deemed as a statement of guaranteed properties. All persons
responsible for applying the equipment addressed in this manual must satisfy themselves that
each intended application is suitable and acceptable, including that any applicable safety or
other operational requirements are complied with. In particular, any risks in applications where
a system failure and /or product failure would create a risk for harm to property or persons
(including but not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby requested to
ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be completely ruled
out. In case any errors are detected, the reader is kindly requested to notify the manufacturer.
Other than under explicit contractual commitments, in no event shall ABB be responsible or
liable for any loss or damage resulting from the use of this manual or the application of the
equipment.
Conformity
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility
(EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified
voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests
conducted by ABB in accordance with the product standards EN 50263 and EN 60255-26 for
the EMC directive, and with the product standards EN 60255-1 and EN 60255-27 for the low
voltage directive. The product is designed in accordance with the international standards of
the IEC 60255 series.
Table of contents
Section 1 Introduction.................................................................................................... 3
1.1 This manual....................................................................................................................................3
1.2 Intended audience........................................................................................................................3
1.3 Product documentation.............................................................................................................. 3
1.4 Symbols and conventions........................................................................................................... 3
1.4.1 Symbols........................................................................................................................................ 3
1.4.2 Document conventions............................................................................................................. 4
Section 2 Safety information.........................................................................................5
Section 3 Interbay bus functions...................................................................................7
3.1 Introduction................................................................................................................................... 7
3.2 Basic configuration...................................................................................................................... 7
3.3 Configuring IEC 60870-5-103 IBB............................................................................................ 10
3.4 Transfer of differential current values....................................................................................11
3.4.1 The delta/dead band algorithm.............................................................................................11
3.4.2 Configuring the SCS differential current parameter.........................................................12
Section 4 IEC60870-5-103.............................................................................................15
4.1 Introduction................................................................................................................................. 15
4.2 General functions........................................................................................................................15
4.3 Disturbance recorder................................................................................................................. 17
4.4 ACC actual channel..................................................................................................................... 18
4.5 Generic REB500 functions........................................................................................................ 19
4.5.1 Diagnostic information........................................................................................................... 19
4.5.2 Status information................................................................................................................... 21
4.5.3 Entries for single-point indications......................................................................................22
4.5.4 Entries for double-point indications ................................................................................... 23
4.5.5 Display of busbar differential currents................................................................................24
4.6 Special information and instructions for configuring the control system.....................26
Table of contents
Distributed busbar protection REB500 1
Communication protocol manual IEC60870-5-103
© Copyright 2019 ABB. All rights reserved
2
Section 1 Introduction
1.1 This manual
GUID-FD38FA69-DDD6-40C9-9185-7AC9C894B6C6 v1
The communication protocol manual describes a communication protocol supported by the
IED. The manual concentrates on vendor-specific implementations.
1.2 Intended audience
GUID-ACC7A898-5907-41E1-8DDD-DD8591298668 v1
This manual addresses the communication system engineer or system integrator responsible
for pre-engineering and engineering for communication setup in a substation from an IED
perspective.
The system engineer or system integrator must have a basic knowledge of communication in
protection and control systems and thorough knowledge of the specific communication
protocol.
1.3 Product documentation
GUID-91F0A03F-D1AF-4695-A239-1FC87E7459EE v2
REB500 manuals Document numbers
Product guide 1MRK 505 402-BEN
Application manual 1MRK 505 399-UEN
Technical manual 1MRK 505 400-UEN
Operation manual 1MRK 500 132-UEN
Engineering manual 1MRK 511 452-UEN
Commissioning manual 1MRK 505 401-UEN
Application manual for bay protection functions 1MRK 505 403-UEN
Technical manual for bay protection functions 1MRK 505 406-UEN
Cyber security deployment guideline 1MRK 511 453-UEN
Communication protocol manual IEC61850 1MRK 511 450-UEN
Communication protocol manual IEC60870-5-103 1MRK 511 451-UEN
Getting started guide 1MRK 505 404-UEN
1.4 Symbols and conventions
1.4.1 Symbols GUID-4F7DD10A-DEE5-4297-8697-B8AAB5E3262F v2
The electrical warning icon indicates the presence of a hazard which could
result in electrical shock.
1MRK 511 451-UEN B Section 1
Introduction
Distributed busbar protection REB500 3
Communication protocol manual IEC60870-5-103
© Copyright 2019 ABB. All rights reserved
The warning icon indicates the presence of a hazard which could result in
personal injury.
The caution icon indicates important information or warning related to the
concept discussed in the text. It might indicate the presence of a hazard which
could result in corruption of software or damage to equipment or property.
The information icon alerts the reader of important facts and conditions.
The tip icon indicates advice on, for example, how to design your project or
how to use a certain function.
Although warning hazards are related to personal injury, it is necessary to understand that
under certain operational conditions, operation of damaged equipment may result in
degraded process performance leading to personal injury or death. Therefore, comply fully
with all warning and caution notices.
1.4.2 Document conventions GUID-37C3ACF4-BD79-43C6-B37E-24B38EE69301 v2
A particular convention may not be used in this manual.
• Abbreviations and acronyms in this manual are spelled out in the glossary. The glossary
also contains definitions of important terms.
• Push button navigation in the LHMI menu structure is presented by using the push button
icons.
For example, to navigate the options, use and .
• HMI menu paths are presented in bold.
For example, select Main menu/Settings.
• Signal names are presented in bold.
The signal 21120_EXT_TEST_TRIP can be set and reset via the LHMI Test Trip menu.
• Parameter names and parameter values are presented in italics.
For example, the default value of the
Operation
setting is
Not inverted
.
• Section references are presented with the respective section numbers.
For example, see Section 1.4.2 for more details about document conventions.
Section 1 1MRK 511 451-UEN B
Introduction
4Distributed busbar protection REB500
Communication protocol manual IEC60870-5-103
© Copyright 2019 ABB. All rights reserved
Other manuals for Relion REB500
17
Table of contents
Other ABB Protection Device manuals
ABB
ABB ret650 User manual
ABB
ABB RELION RER670 Instructions for use
ABB
ABB NEXUS Series User manual
ABB
ABB RELION 650 SERIES User manual
ABB
ABB Relion User manual
ABB
ABB REB650 User manual
ABB
ABB Relion REG670 Quick start guide
ABB
ABB REX 521 Use and care manual
ABB
ABB Relion 615 series User manual
ABB
ABB Relion REB500 Quick start guide
ABB
ABB RED670 Relion 670 series User manual
ABB
ABB RET630 User manual
ABB
ABB RER620 User manual
ABB
ABB REG650 ANSI User manual
ABB
ABB Relion 620 Series Instructions for use
ABB
ABB REM615 ANSI User manual
ABB
ABB Relion 670 series Quick start guide
ABB
ABB POLIM User manual
ABB
ABB REM615 ANSI Datasheet
ABB
ABB Relion 670 series User manual
