ABB 6AGC085345 User manual

—

MANUAL

Pedestal for Terra AC wallbox

Installation manual

• TAC pedestal single (ABB6AGC085345)

• TAC pedestal back-to-back (ABB6AGC085684)

—

Pedestal for Terra AC wallbox

Installation manual

2PEDESTAL FOR TERRA AC WALLBOX

INSTALLATION MANUAL 3

Warning!

Not observing the safety instructions can result

in risk of death, injuries and damage to the de-

vice! The producer assumes no liability for claims

resulting from this!

Electrical hazard!

The installation, commissioning and maintenance

of the charging station may only be performed by

correctly trained, qualified and authorized

electricians who are fully responsible for the com-

pliance with existing standards and installation

regulations.

Observe the instructions given for selecting the

location and the constructional requirements!

If the specifications for the location are not ob-

served, this can result in death, serious physical

injury or equipment damage if the corresponding

precautionary measures are not met!

—

Safety instructions

This installation manual is intended for qualified

personnel only.

This guide is a supplement to the "Terra AC wall-

box Installation Manual." The information and in-

structions in the manual about selecting the loca-

tion, installation and connection of the charging

station must be adhered to.

(1) Persons who, due to their special training, expertise and experience as well as knowledge of current standards, are able to assess the work

performed and the possible hazards.

—

Use of this manual

4PEDESTAL FOR TERRA AC WALLBOX

—

Intended use

A pedestal for free-standing installation in inside

or outside areas is available as an alternative to

mounting the charging station on a wall.

Depending on the design and number of charging

stations the relevant number of empty pipes and

connection cables should be taken into consider-

ation in the concrete foundation.

If the charging station is installed with a plug-in

power supply line (e.g., for demonstration pur-

poses), you should ensure that there is sufficient

tension relief and edge protection for the power

supply line.

The respective national regulations must be ob-

served with regard to the installation of the

pedestals.

Weight (without charging station): 10,5 kg (single

/ back-to-back)

TAC Pedestal Single



Back-to-Back Pedestal



 SCREW; FLAT HEADED



Stainless steel

 SCREW; FLAT HEADED



Stainless steel

 





 





   

   

   

INSTALLATION MANUAL 5

—

Overview

—



The single pedestal is designed for the

installation of one charging station.

—



The back-to-back pedestal is designed for

the installation of two charging stations.

No Yes

6PEDESTAL FOR TERRA AC WALLBOX



• All of the location requirements for the

charging station in the " Installation manual"

must be adhered to!

• When mounting the pedestals in parking spaces

or parking garages, appropriate anti-collision

protection must be provided by the customer.



• The calculation, design and manufacture of the

concrete foundation lies in the scope of

responsibility of the producer of the site.

• A horizontal, level and sound foundation is

required for installation.

To ensure safe and permanent anchoring, we

recommend creating a concrete foundation:



Concrete: C30/37

• The base must permit the running off of any

water that has entered the base.

• All cables must be laid precisely in the centre of

the concrete foundation from the base and

must have an excess length of approx. 1.5 m for

the remaining installation activities.

• During the production of the concrete

foundation, the cables must be protected

against damage using appropriate measures

(e.g., a protective tube). The protective tube

must have an excess length of approx. 25 cm

above the concrete foundation.

• Mounting the pedestal on asphalt is not

allowed!

—

Warning

—

Location requirements

Electrical hazard!

The back-to-back pedestal must always be fitted

with two charging stations!

INSTALLATION MANUAL 7

—

Positioning the base

200

1306

700

500 100

600

100

500 1306100

Position the base below street level. The pavement can cover the base. See drawings below.

PEDESTAL FOR TERRA AC WALLBOX

The 4x anchors (M10x40) must be used for

anchoring.

—

Technical data

Anchorage ground Standard concrete

with a strength class of





Recommended load Tension N (uncracked

concrete)



Per anchor Transversal shear V

(uncracked concrete)



Required clearance 

Max.Torque Tinst 

Drill-hole diameter do 

 

Making drill holes

• Mark the 4 holes on the concrete foundation

using the base plate of the pedestal. Make sure

that the connection cable is located precisely

underneath the opening in the base plate.

• Drill the 4 mounting holes:

Diameter: 12 mm

Drill-hole minimum depth: 43 mm

• Hammer the anchors (not included) so that

they are flush with the floor.

Please also observe the following instructions:

Instructions on inserting the anchors

—

Anchoring to the base

Tinst

I=hnom

INSTALLATION MANUAL 9

345mm

200

1406 mm

245 mm

100

200

22,5

300 22,5

200

DETAIL C

SCALE 1 : 2



• Thread the connection cables from the bottom

through the pedestal upwards through the

cable opening.



• Position the pedestal directly over the cable

outlet.

• Anchor the pedestal to the foundation using 4

bolts M10 and washer M10 (not included).

NOTE

THE IMAGES ARE VALID FOR ALL VERSIONS.

Pedestal from

below

200

300

ISO 4017-

M12x 35

DIN125 -

Washer

 PEDESTAL FOR TERRA AC WALLBOX

Grounding point



• If necessary, connect the earthing to the

pedestal's grounding point with included



Max torque: 4 Nm.

Add edge cable protection

• Add the edge protection on the cable

opening of the pedestal immediately before

installing the charging station (see figure).

• 

345

245

200

300

DETAIL A

SCALE 1 : 2

ISO 4017-

M12x 35

DIN125 -

Washer

DETAIL B

SCALE 1 : 2

345

245

200

300

DETAIL A

SCALE 1 : 2

ISO 4017-

M12x 35

DIN125 -

Washer

DETAIL B

SCALE 1 : 2

345mm

200

1406 mm

245 mm

100

200

22,5

300 22,5

200

DETAIL C

SCALE 1 : 2

This manual suits for next models

Table of contents

Popular Industrial Electrical manuals by other brands

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Project planning manual

Abtech

Abtech HVJB Series Installation, operation & maintenance instructions

Murata

Murata GRM0335C1H8R1DA01 Series Reference sheet

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Installation and operation manual

Eaton

Eaton Ulusoy HMH24-04 user manual

Newlong

Newlong NP-7H NSTRUCTION MANUAL/PARTS LIST

Murata

Murata GJM0335C1E4R4BB01 Series Reference sheet

Stahl

Stahl 8575/12 operating instructions

SI Pegasus installation instructions

Murata

Murata GRM1555C1H2R7CA01 Seies Reference sheet

Murata

Murata GRM0225C1E6R4BA03 Series Reference sheet

Cooper Power Systems

Cooper Power Systems VXE15 Installation and operation instructions

S&C

S&C Vista SD manual

Murata

Murata GRM0335C2A7R3CA01 Series Reference sheet

Siemens

Siemens 3VA9988-0BM10 operating instructions

Siemens

Siemens SITRANS LVS100 operating instructions

Murata

Murata GRM32ER60G227ME05 Series Reference sheet

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series manual