ABB ACS 600 Operating and maintenance instructions

Other manuals for ACS 600

3

Table of contents

Other ABB DC Drive manuals

Popular DC Drive manuals by other brands

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS user manual

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Technical description

Chamberlain Garog

Chamberlain Garog D Series operating manual

Parker

Parker PDS Series user guide

Festo

Festo DGC G Series Repair instructions

Binks

Binks QS-5012-1-CE Service manual

Danfoss

Danfoss VLT 2800 Series Quick setup

YASKAWA

YASKAWA CANopen SI-S3 Technical manual

GE

GE D20A6 instructions

Unex

Unex MC-D-250-1000-050W-TW operating manual

Geckodrive

Geckodrive G213V manual

Rockwell Automation

Rockwell Automation PowerFlex 700S Programming manual

WEG

WEG DeviceNet CFW500 user manual

Siemens

Siemens SINAMICS G List manual

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Operating instructions & installation instructions

SOMFY

SOMFY JR RU 30 instructions

Beckhoff

Beckhoff AX8911 Documentation

Minarik

Minarik MM300 Series user manual

6

Lead the motor and mains cables through the

bottom plate.

ENSURE MAINS SUPPLY TO INSTALLATION IS OFF.

LOCK THE DISCONNECTOR TO OPEN POSITION.

ACx 600 MUST BE INSTALLED BY A COMPETENT PERSON.

IF IN DOUBT DO NOT INSTALL.

1

1. Measure the places for four screw holes.

Mark the hole positions. 2. Drill the holes.

3. Screw in the screws.

2

Position ACx 600 onto screws and securely

tighten in all four corners.

Note:

Lift ACx 600

by its chassis, not by its cover.

1. Undo the two screws. 2. Lift the lower edge

of the cover. 3. Disconnect the cable from

connector X2. Remove the cover.

STOP

FOR

INSTALLATION

OF OPTIONAL

EQUIPMENT,SEE

SEPARATE

INSTRUCTIONS

INCLUDED IN

THE DELIVERY.

4 5

1. Strip off the insulation from the motor cable

and mains cable. Twist the screen wires into

bundles. 2. Make suitable holes to motor and

mains cable grommets.

Before Starting Installation

CHECK BOX CONTENTS: ACx 601, Manual(s), Testing report, Ordered options, Quick Guide(s)

CHECK INSTALLATION SITE AMBIENT CONDITIONS: See Manual.

CHECK INSTALLATION SPACE: ACx 600 free space requirements are 300 mm above and below, 50 mm on the left and on the right.

CHECK INSTALLATION SURFACE: Vertical, smooth and solid, free from heat, damp and condensation.

CHECK ACCESSORIES NEEDED: See Manual for fuse, supply disconnecting device and cable specifications.

3

Mains cable

OUTPUT

STOP

CHECK THE

INSULATIONS

OF MOTOR,

AND MAINS

AND MOTOR

CABLE.

See Manual.

7

2.

1.

3.

2.

1.

3.

1.

2.

INPUT

Motor

cable

300 mm

free space

ACS 600 Installation Guide

ACS/ACC/ACP 601-0005-3 ... -0016-3,

-0006-5 ... -0020-5 and -0009-6 ... -0020-6

10

6-7

6-7

15

X2

1. Connect the motor cable.

2. Connect the mains cable.

Ensure proper earthings.

For minimal radio frequency

interference (RFI) at the motor

end:

1.Twisted screen:

Diameter (Ø) > 1/5 ·Length (L),

or

2. Screen 360° earthing at cable

lead-through.

LØ

8

9

Control cable installation:

1. Make hole in a control cable

grommet and lead the cable into

the unit.

2. Connect the earthing wires

and the cable shield to the

earthing terminal next to the

NIOC board.

3. Connect the control cables to

the input/output terminals.

1. Connect the control panel

cable to connector X2.

2. Replace the front cover.

10

1.

2.

2.

1.

Earthing Wires

and the cable shield 3.

300 mm

free space

ABB Industry Oy Drives P.O. Box 184 FIN-00381 Helsinki tel: +358-10 22 2000 fax: +358-10 22 22681

Code: 3AFY 59019902 R0125

Effective: 3.3.1998/EN

Standard

Input/Output

Connections: See

the

Start-up

Guide

or Manual.

X2