A4Tech MeetingMan G10-700F User manual

MeetingMan

Wireless Mouse

User Manual

Model: G10-700F

www.a4tech.com

- 1 -

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE

MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MAY CAUSE UNDESIRED OPERATION.

Federal Communications Commission Requirements

The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

●Reorient of relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S

AUTHORITY TO OPERATE THE EQUIPMENT.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and receiver.

(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

The equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in

Supplement C to OET65. The equipment has very low levels of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR).

- 2 -

1. Hardware Installation

1). Connect the 10-Link receiver

Take out the 10-Link receiver from bottom of the mouse and connect it to your computer or

Notebook.

Notes:

1. If you are using the receiver in a long range meeting room or there is strong wireless

conflicts nearby, adopting the receiver with a USB extension cable to keep it away from the

computer or any interfering sources.

2. Connect receiver on the same side with the mouse, it may avoid potential wireless

conflicts from the notebook computer.

2). Insert the batteries

Push down the mouse cover to open the battery cover and insert the supplied batteries.

Please make sure the positive (+) and negative (-) ends of the battery match the polarity

indicators inside the battery compartment.

3). Turn on your Mouse

Push the power switch to ON position and turn on your mouse. >>Then LED light at the

bottom of the mouse is on immediately.

- 3 -

2. Software Installation(Note: The software is applicable to Windows 2000/ XP/ 2003/ Vista/ Windows 7)

The G10 MeetingMan offers 2 flexible ways to install the driver, Normal Installation and Mobile Execution. The MeetingMan

main program has a special feature that it can be executed directly without the need to install the software to Windows

system. This is convenient when you are using a public computer and installing mouse driver to the system is prohibited or

restricted. In such circumstances, you do not need to install the mouse driver, but just run the MeetingMan＇s main

program directly from your storage device, e.g., a memory stick.

Normal Installation

1). Uninstall any mouse software on your system.

2). Insert enclosed CD to start installation and follow the on-screen instructions to finish the

software installation. You may manually double click the “auto-run＂program if execution

does not automatically start.

3). The shortcut icon " " will appear on your desktop screen, and then you have successfully

installed the software. (Otherwise, installation is failed and you have to remove the software

and re-install.)

To remove the driver, follow the steps:

Go to START>> PROGRAMS >>A4TECH Software >> "G10 MeetingMan" >> "Uninstall G10

MeetingMan, see figure on the right.

Mobile Execution:

You may copy and store the Mobile Edition files to your storage device, e.g., a memory stick,

and plug it into any public systems to execute the Mobile Edition directly without installation.

Or, you may copy all the files to the system, and then run the Mobile Edition main program

- 4 -

directly. This is convenient when you are using a public computer in the school or net bar,

where installation any new program is prohibited or restricted.

Mobile Edition.exe

Usage:

1). Copy all the files in the folder “G10＂to your memory stick, and if needed, copy the files

to the public system.

2). Double-click the icon to run Mobile Edition.exe

(1) Knowing the G10 MeetingMan Software

The basic principles

and design concepts of

G10 MeetingMan

Before you are getting started to use this product, it is vital to understand the basic principles

and design concepts of MeetingMan.

For each of MeetingMan’s script file, it will contain 5 different working modes, and each

working mode can setup 7 buttons on the mouse with various functionalities. Those preset

modes can be accessed by pressing the “mode-shift” button, and each button’s functionality

can be activated by clicking the appropriate mouse button according to various applications.

Thus, it turns a simple mouse into a very unique and powerful tool with individual’s innovation.

For instance, there are 5 preset working modes available for Office, TutorPen Meeting, Open

file, LaserPointer Meeting and Gaming respectively, and after the MeetingMan software being

installed, those 5 working modes can be shifted using a “mode-shift” button and make your

jobs well done effortlessly!

Functions Descriptions Figures

- 5 -

. Mode Name/Select

Click on “Mode Name/Select” on the Main Menu, the mode setup

screen will pop up as shown on the right.

You may tick off the modes you would not need temporarily from

bottom to top order, or tick the mode you need from top to bottom

order.

You may enter a new mode name on the blank, or edit existing mode

names.

. Selected Mode to

Edit

It displays the current mode number in editing. You may select other

mode numbers if needed.

There are 5 modes you can select to edit; with each mode you can

define a number of new button settings. Remember to click “Apply” on

the main menu to save the new settings to the receiver before taking

effect.

③. Mode Name

The current mode name in editing. You may edit the mode name as

described in the “1.Mode Name/Select” section.

- 6 -

④. Default

Click the "Default" a reminder will pop up as shown on the right. Click

"OK" will resume all the buttons to the original settings, or click

"Cancel" to exit the screen without any change.

- 7 -

(2) Button Settings and Relevant Functions

Functions Descriptions Figures

Button

Settings

Click any “button definition area” on the main menu; you will see the function listing

as shown on the right. According to your preference, you may select one of them as

the button setting. You also can enter a short description on the “Description of

reminder” area, which will be displayed on the screen when it is activated as the

reminder.

No Setting There is no button setting being defined.

Figure 1

Keyboard You may setup the mouse button to simulate a keyboard's

keystroke, or a key combination with "Win", "Ctrl", "Shift" and "Alt",

then followed with any keystroke on the keyboard, and then assign it

to the designated mouse button.

Mouse Except mouse left button, you may setup any of mouse buttons to

be one of "mouse left button, mouse right button, mouse middle

button, mouse 4th button, mouse 5th button, wheel up and wheel

down".

Open a File

One click to open a program file or a document. You may setup any

of mouse buttons of 2, 3, 4, 5, 6, wheel up(UP) and wheel down(DN)

with “Open a File” function.

Usage:

1). Select “Open a file” from the pull-down button menu as figure 1

shows.

2). A screen of file listings will pop up as figure 2 shows.

3) Select one of the files that you would open it with the associated

button and click “Open”.

4) Now you can see the file you selected has been assigned to the

button.

5) Click “Apply” to save the new button setting.

- 8 -

Memo

Example:

While in the session of a meeting or teaching, it is embarrassing to

keep others waiting due to searching for a document, or look up for

a program or a shortcut. With “Open a File” function, you may have

better way to resolve this issue. By setting up each button in

association to the document, program or shortcut, all you need to do

is to shift to the mode and click each mouse button to open all the

files instantly. You may also open an on-line reminder to check each

mouse button association details.

See below “Memo” section in more details.

One click to open the Memo screen and list out all the current button

settings as the reminder. You may setup any of mouse buttons of 2,

3, 4, 5, 6, wheel up(UP) and wheel down(DN) with “Memo” function.

Usage:

1). Select “Memo” from the pull-down button menu of G10

MeetingMan main menu as figure 3 shows.

2). Click “Apply” to save button setting.

Example:

This function is useful during the session of a meeting or teaching,

when you are not very sure which button is associated with the

function you need.

Click the “Memo” button will bring the “Memo” screen as figure 4

shows. Now you can check each button setting and activate them

immediately.

For instance, the teacher can open all the handout documents in

seconds by clicking the button in association with the mouse

buttons.

The Memo function is available for mouse button 2, 3, 4, 5, 6, Wheel

up(UP) and Wheel down (DN).

Figure 2

Figure 3

Figure 4

- 9 -

Office Sets

You may setup any one of Office command sets such as: “Zoom In,

Zoom Out, Paste Text, Double Click and Treble Click”to the mouse

buttons.

Zoom In/Out：One click to perform zoom in or zoom out function,

applicable to CAD, ACDSee, Windows or text editing programs.

Paste Text：One click to perform “Select, Copy & Paste” texts, it

turns office jobs can never be so simple.

Key

Combination

Quick access to Office commands of key combinations, such as:

Cut, Copy, Paste, Delete, Search, Select All, Redo, Undo, New File,

Open File, Save File, Print…etc.

Multimedia Quick access to Multimedia commands, such as: Media Player

(Open), Previous, Next, Stop, Play/Pause, Mute, Volume+,

Volume-…etc.

Internet Quick access to usually used Internet commands, such as:

Backward, Forward, Stop, Refresh, Search, My Favorite, Web

Browser, E-mail...etc.

System Quick access to Windows commands, such as: Open Calculator,

Open My Computer, Sleep, Power Off...etc.

Gesture

16-in-1 This 16-in-1 mouse utility offers 16 directions to draw the lines with

the mouse and the preset commands will be executed immediately.

Note that this gesture function is only available for mouse button 

and . See more details on the Gesture 16-in-1 section.

LaserPointer

(By Model) The LaserPointer is only available by models, if your model does not

have LaserPointer, please use TutorPen instead. (Note that the

LaserPointer switch will still in working even when the computer is

power off, remember to switch off the mouse power on your long

journey)

Other A4Tech Mouse manuals

Popular Mouse manuals by other brands

Sven

Sven RX-G720 user manual

3DConnexion

3DConnexion CadMouse Pro manual

Canyon

Canyon Puncher GM-20 manual

Sharkoon

Sharkoon Light2 180 manual

Cherry

Cherry MW 8C ERGO user manual

NGS

NGS HIT RB manual

Sharkoon

Sharkoon FireGlider manual 

Lenovo

Lenovo Wireless Mouse N3902 quick start guide

BASETech

BASETech BN-S11 operating instructions

Dell

Dell WM326 user guide

Areson

Areson B213 user guide

HP M17587-371 manual

Chatpen

Chatpen CHA-30 user manual

GAMDIAS

GAMDIAS DEMETER GMS5000 Quick installation guide

HP KJ453AA - Wireless Laser Mouse datasheet

Trust

Trust GRAPHIN GXT 960 user guide

Lenovo

Lenovo SD-9082 Product guide

Alienware

Alienware AW320M user guide