A.I.&.E Toronto User manual
871125224943
A.I.&E. Adriaan Mulderweg 9-11,
5657 EM Eindhoven, The Netherlands
Edco UK Ltd,Two Chamberlain Square,
Birmingham B3 3AX,
United Kingdom
UK Electric heater with replace effect
DE Elektrische Heizung mit Holzfeuereffekt und Kaminsims
FR Chauffage électrique, effet cheminée et manteau de cheminée
NL Elektrische kachel met haardeffect en schoorsteenmantel
IT Radiatore elettrico con effetto caminetto e mensola
ES Chimenea eléctrica con efecto llama y repisa
Instruction manual
Bedienungsanleitung
Manuel d’utilisation
Gebruiksaanwijzing
Manuale di istruzioni
Manual de instrucciones
TORONTO
TORONTO
INSTRUCTION MANUAL
Model: RO2716-32Z
Item number 871125224943
A.I.&E Adriaan mulderweg 9-11
5657 EM Eindhoven
The Netherlands
ATTENTION:
1. Find a location for the electric heater that is protected
from direct sunlight.
2. Do not plug the electric heater into the power outlet
before you read all instructions.
3. READ ALL INSTRUCTIONS BEFORE USE
AND SAVE IT.
Important
• Please read all instructions carefully before using
this product.
• Make sure that the voltage rating label on the type
plate corresponds to your main voltage. If not see
your retailer and do not connect the appliance.
• Never use the appliance unsupervised when in
use.
• If you have to leave even for a short moment
please stop the appliance.
• Keep out of reach of children and do not allow
them to operate this appliance
• Only use the appliance for domestic purposes and
in the way indicated in these instructions.
• From time to time check the cord for damages.
Never use the appliance if the cord or any part of
the appliance shows any signs of damage.
• If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
• Make sure the connection cord does not touch
any hot surfaces.
• WARNING: In order to avoid overheating, do not
cover the heater.
• Keep the appliance at least 15cm (6inches) from
side walls and any other objects, to permit a good
air circulation.
• Do not use the appliance outdoors
• Do not use if you have wet hands.
• Never use the appliance on or near hot surfaces.
• Never move the appliance by pulling the cord.
• Before cleaning the appliance, make sure it is
unplugged from the power and that it is completely
cooled.
• Do not clean the appliance with abrasive
chemicals.
• Never use accessories that are not recommended
or supplied by the manufacturer. It could cause
danger to the user or damage to the appliance
• Never route the mains cable beneath carpet.
• Never use the heater to dry clothes or any other
similar items.
• The heater must not be located immediately below
a socket outlet.
• This heater must not be used with an extension
lead.
• Dot use this heater with a programmer, timer
or any other device that switches the heater on
automatically, since a re risk exists if the heater
is covered or positioned incorrectly.
• Do not use this heater in the immediate
surroundings of a bath, a shower or a swimming
pool.
• CAUTION: In order to avoid a hazard due to
inadvertent resetting of the thermal cutout, this
appliance must not be supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched on
and off by the utility.
• This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
• Children of less than 3 years should be kept away
unless continuously supervised.
• Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided
that it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
• CAUTION — Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
• WARNING: This heater is not equipped with a
device to control the room temperature. Do not
use this heater in small rooms when they are
occupied by persons not capable of leaving the
room on their own, unless constant supervision is
provided.
Electrical Parameter model: RO2716-32Z
Power supply: AC220-240V
Frequency: 50-60Hz
Power: 2000W
Dimensions WxDxD(mm): 812x220x410
Weight (KG): 16,5
NOTE: If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualied persons in order to avoid a hazard.
Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities.
Contact your local government for information regarding the collection systems
available.
If electrical appliances are disposed of in landlls or dumps, hazardous
substances can leak into the groundwater and get into the food chain, damaging
your health and well-being.
Parts list
REF NO DESCRIPTION QTY
A 3 PCS
B 3 PCS
C 1 PC
Installation
Please be aware: that no products should be sealed against the wall/opening as
this can effect the performance of the heater unit.
Minimum Installation Height:
From oor level to bottom edge of product, Minimum 300mm.
This suite is supplied with a wall xing Bracket. The suite can be installed
at any height as long as it is not below the recommended 300mm. (Please
note the 700mm measurement is given as a common installation height). The
recommended installation height is a minimum of 300mm from the oor level to
the underside of the hearth.
Warning: Installing this product below 300mm will
cause overheating issues.
The suite is designed as a wall mounted suite; it is
not suitable to be installed at oor level.
Installation:
This model is provided with a wall mounting bracket along with x3 screws and
wall plugs.
PLEASE NOTE: The screws and plugs provided are only suitable for a solid wall
xing. If the installation is onto a hollow/stud wall, we recommend that heavy
duty wall anchors or equivalent are used.
To install the product:
1. Measure 700mm from the oor level up the wall, Mark this measurement
with a pencil.
2. Place the bottom edge of the wall bracket on the 700mm mark, level using a
spirit level and mark and drill the x3 xing holes.
3. Using the correct wall xings screw and x the wall bracket in place.
4. Locate the x3 slots in the rear of the product, carefully align these slots with
the prongs on the wall bracket, lift and slot the product into place.
5. Locate the power cable socket on the bottom right hand side, underneath the
hearth on the re, and plug the power lead in.
6. Keep the appliance at least 15cm (6inches) from side walls and any other
objects, to permit a good air circulation.
7. The product is now ready to use.
Operating Instructions
Once the electric heater has been properly installed and connected to a ground
electrical outlet, it is ready to operate.
Note: Ensure the circuit breakers for the power supply are turned on.
The heater controls are located right of the heater outlet.
Control Panel
LED Screen Remote Control
O/I: Press this switch, the unit power-on. When the O/I switch is turned off, all
other functions will stop even though the buttons may be in the ON position.
: Press this button, the unit will enter standby mode. The unit will beep and
the indicator light will be on. Then you can select the following functions as
desired. Press again to turn off the heater.
: For modication time function - Press this button, the ‘SUN’ on the LED
screen starts to twinkle. Press up or down button to the desired date, and
press button to select, press button to cancel. After set the desired date,
press button switch to the ‘hour’ position. Press or button to the desired
hour. Press button switch to the ‘minute’ position. Press or button to the
desired minute. Press or button to complet date setting.
NOTE: The date will be reset after power interrupt.
: For automatic working time setting function - There are 10 time
periods you can set to make the unit work automatically. Press this button,
time serial number starts to twinkle. The ‘ON’ on the LED screen lights up.
Press or button to the desired serial number. Press button again, the
‘SUN’ on the LED screen starts to twinkle. Press up or down button to
the desired date, and press button to select, press button to cancel. After
set the desired date, press button switch to the ‘hour’ position. Press or
button to the desired hour. Press button switch to the ‘minute’ position.
Press or button to the desired minute. At this time you have completed
the boot time setting. Press button again, the ‘ON’ extinguished and the
‘OFF’ lights up. Complete the shutdown time in the same way. Finally, you need
to set a temperature which stop heating. Press or button to the desired
temperature. When desired ambient temperature is reached, the heater will
automatically stop heating.
: For Window detection function - Press this button to turn on the
window detection function. During the heating process, if the room temperature
drops obviously caused by the outdoor cold air blowing, such like open windows
or open the door. In order to save energy, the heater will automatically stop
heating. The corresponding icon on the screen will twinkle. Press again to turn
off the window detection function to normally heating.
: For reset function - Press this button to clear the Timing parameters.
: For heat function - Press this button to turn on the heat function.
Press again to turn off.
: For timer function - Press this button to turn on the timer function.
Press again to turn off.
Note: the working state of the time period is the same as that before start timer
function. That is to say, adjust the working state you want and turn on the timer
function, then the machine will work according to your working state in the
time period.
: For ame function - Press this button to turn on the ame.
Press again to turn off.
: For ame effect function - Press this button to change ame effect.
Press again to decrease the ame intensity. There are 4 light intensities for your
selection. The ame optics will go lower under the sequence of 4,3,2 and 1.
Pressing the button again will go higher under the sequence of 1,2,3 and 4.
NOTE: After the display screen is extinguished, it can be activated by any key.
NOTE: In the absence of timing mode, you can press or button to the
desired temperature directly. When desired ambient temperature is reached, the
heater will automatically stop heating.
Fast Menu:
Press the standby button and the heating button, the unit can heating
immediately.
This manual suits for next models
1
Table of contents
Languages:
