3One data IES2005 User manual
IES2005
Unmanaged Industrial Ethernet
Switch Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website:
www.3onedata.com
Tel:
+86 0755-26702688
Fax:
+86 0755-26703485
【
Package checklist
】
Please check whether the package and accessories are intact
while using the switch for the first time.
1.
Industrial Ethernet switch
2.
Certification
3.
Quick installation guide
4.
Warranty card
5.
DIN-Rail mounting attachment
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【
Product Overview
】
This product is full 100M unmanaged DIN-Rail industrial
Ethernet switch. The model is IES2005 (5 100M copper ports
+ 1 12~48VDC/24VAC power supply)
【
Panel design
】
Rear view, bottom view and top view
Front view and side view
1. DIN-Rail mounting kit
2. Power supply input terminal block
3. DIP switch
4. Grounding screw
5. Power supply input status indicator PWR
6. Copper port connection indicator
7. 100M Ethernet copper port
【
Mounting Dimension
】
Unit: mm
Attention before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【
DIN-Rail Mounting
】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:
Check whether the DIN-Rail mounting kit thatStep 1 comes with the device is installed firmly.
Insert the bottom of DIN-Rail mounting kit (one sideStep 2 with spring support) into DIN-Rail, and then insert
V-
F G
1 2-4 8 VD C /24 VA C
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Check and confirm the product is firmly installed onStep 3 DIN-Rail, and then mounting ends.
【Disassembling DIN-Rail】
Power off the device.Step 1 After lift the device upward slightly, first shift out theStep 2 top of DIN-Rail mounting kit, and then shift out the
bottom of DIN-Rail, disassembling ends.
Attention before powering on:
Power ON operation: first connect power line to the
connection terminal of device power supply, and then
power on.
Power OFF operation: first unpin the power plug, and
then remove the power line, please note the operation
order above.
【Power Supply Connection】
DC power supply
This series provide 3-pin 5.08 pitch power
input terminal blocks. Power supply range:
12~48VDC/24VAC
【DIP Switch Settings】
It provides 4-pin DIP switch for function settings,
among which “ON” is enable valid end.
The definitions of DIP switch are as follows:
DIP
Definition
Operation
1 Loop detection Set the DIP switch to ON to
enable the loop detection
function.
2 Storm suppression Set the DIP switch to ON to
enable the storm suppression
function.
DIP
Definition
Operation
3
One-key VLAN
Set the DIP switch to ON to
enable VLAN function, port 1
can communicate with other
ports, while other ports are
isolated from each other.
4 Flow control Set the switch to ON to enable
the flow control function
【Checking LED Indicator】
The function of each LED is described in the table as below:
LED
Status
Description
PWR ON Power supply is connected and
running normally
OFF Power supply is disconnected
and running abnormally.
Link/ACT
(1-5)
ON Ethernet port connection is
active.
Blinking
Data transmitted
OFF Ethernet port connection is
inactive.
【Specification】
Panel
100M copper port
10/100Base-T(X) self-adapting
RJ45 port, full/half duplex
self-adaption, support
MDI/MDI-X self-adaption
Indicator Power indicator, interface
indicator
Exchange attributes
Backplane bandwidth
1G
MAC table size
2K
Power supply
Input power supply
12~48VDC/24VAC
Access terminal
3 pins 5.08mm pitch terminal
blocks
Support anti-reverse connection
and over-current protection
Consumption
No-load
0.4W@24VDC
Full-load
1.0W@24VDC
Environmental Limits
Working temperature
-40~75
℃
Storage temperature
-40~85
℃
Working humidity
5%~95% (no condensation)
Protection grade
IP40 (metal shell)
MTBF
510465 hrs
Other 3One data Switch manuals
3One data
3One data IES6100 Series User manual
3One data
3One data IES618 Series User manual
3One data
3One data IES206G-2GS User manual
3One data
3One data ICS6400-12GT12GS4XS User manual
3One data
3One data IPS7112G-4GS-8GPOE User manual
3One data
3One data IES716-2GS User manual
3One data
3One data IPS7112G-4GS-8GPOE User manual
3One data
3One data IES2008 User manual
3One data
3One data IES215 Series User manual
3One data
3One data IPS3110 Series User manual
3One data
3One data IES2210 Series User manual
3One data
3One data IES215-1GX-4G User manual
3One data
3One data SW4485I User manual
3One data
3One data IES6100PN-8T-2LV User manual
3One data
3One data IES716-2GS User manual
3One data
3One data IES7120G Series User manual
3One data
3One data TNS5500 Series User manual
3One data
3One data IPS7112G-4GS-8POE User manual
3One data
3One data ICS5428 Series User manual
3One data
3One data IES205 Manual
