3One data ES209G-1GF User manual
ES209G-1GF
Unmanaged Ethernet Switch Quick
Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website:
www.3onedata.com
Tel:
+86 0755-26702688
Fax:
+86 0755-26703485
【Package Checklist】
Please check whether the package and accessories are intact
while using the switch for the first time.
1.
Industrial Ethernet switch
2.
Certification
3.
Quick installation guide
4.
Warranty card
5.
DIN-Rail mounting attachment
6.
Terminal
blocks
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
The product is full Gigabit unmanaged DIN-Rail Ethernet
switch. Module as follows: ES209G-1GF (8 Gigabit copper
ports + 1 Gigabit fiber port).
【Panel Design】
Rear view, Top view and Bottom view
Front view and Side view
1. Location hole for wall mounting
2. DIN-Rail mounting kit
3. DIP switch
4. Power input terminal block
5. Grounding screw
6. 1000Base-X Gigabit Ethernet fiber port
7. Power supply input status indicator
8. 10/100/1000Base-T(X) Ethernet port
9. Interface indicator
【Mounting Dimension】
Unit: mm
Attention before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【DIN-Rail Mounting】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:
Check if the DIN-Rail mounting kit is installed firmly.
Step 1
Insert the bottom of DIN-Rail mounting kit (one side
Step 2
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Check and confirm the product is firmly installed on
Step 3
DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Device power off.
Step 1
After lift the device upward slightly, first shift out the
Step 2
top of DIN-Rail mounting kit, then shift out the
bottom of DIN-Rail, disassembling ends.
Attention before power on:
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then
remove the power line, please note the operation order
above.
【Power Supply Connection】
DC power supply
The device provides 4 pins 7.62mm pitch
power supply input terminal blocks and
two independent DC power supply
systems for PWR1 and PWR2. The power
supply supports anti-reverse connection.
Power supply range: 12～48VDC
【DIP Switch Settings】
The device provides 4 pins DIP switches for
function settings, where "ON" is enable valid
terminal. Please power off and power on after
changing the status of DIP switches. DIP switches definition
as follows:
DIP
Definition
Operation
1
Flow control
Set the DIP switch to ON
2
Reserved
-
3
Port isolation
Set the DIP switch to ON, fiber
DIP
Definition
Operation
port can communicate with
copper port. Copper ports can’t
communicate with each other.
4
Reserved
-
【Checking LED Indicator】
The function of each LED is described in the table as below:
LED
Status
Description
P1/P2
ON
P1/P2 is running normally
OFF
P1/P2 is disconnected and running
abnormally.
Link/Act
(G1-G9)
ON
Ethernet port connection is active.
Blinking
Data transmitted
OFF
Ethernet port connection is inactive.
【Specification】
Panel
Gigabit copper port
10/100/1000Base-T(X), RJ45,
automatic flow control, full/half
duplex mode, MDI/MDI-X
autotunning
Gigabit fiber port
1000Base-X, SC interface
Indicator
Power indicator, interface
indicator
Exchange attributes
Backplane bandwidth
20G
Packet buffer size
1Mbit
MAC table size
8K
Power supply
Input power supply
24VDC (12~48VDC)
Support dual power supplies
redundancy,
reverse-connection protection
Access terminal
4 pins 7.62mm pitch terminal
blocks
Consumption
No-load
3.9W@24VDC
Full-load
8.1W@24VDC
Working environment
Working temperature
0~55℃
Storage temperature
-10~65℃
Working humidity
5%~95% (no condensation)
Protection grade
IP30 (metal shell)
Other 3One data Switch manuals
3One data
3One data IES5028G-4GS-8GC User manual
3One data
3One data ES1008G-8POE-150W-P User manual
3One data
3One data ICS5428 Series User manual
3One data
3One data IES615-2DI(3IN1) Series User manual
3One data
3One data TNS5500D Series User manual
3One data
3One data IES615-2DI Series User manual
3One data
3One data TNS5800 Series User manual
3One data
3One data IPS716-2GC-4POE User manual
3One data
3One data IES3016L Series User manual
3One data
3One data IPS716-2GC-4POE User manual
3One data
3One data IES6200-PN-16T4GS-2P48 User manual
3One data
3One data TNS5800 Series User manual
3One data
3One data IES6300 Series User manual
3One data
3One data PS5026G-2GS-24PoE User manual
3One data
3One data IPS7110-2GC-8POE User manual
3One data
3One data IES6300-8GHP2GS2HS-2P48-360W User manual
3One data
3One data IES6210 Series User manual
3One data
3One data IES618 Series User manual
3One data
3One data IES2305 Series User manual
3One data
3One data IES5024 Series User manual
