3D Systems Cubify CUBEX Duo User manual

CUBEX

Measuring

Stepper motor

chip voltages

Contents

What you will need ..................................................................................................... 3

Removing the Jet Wipe .............................................................................................. 4

Removing the Case and floor panel. .......................................................................... 4

Voltage Measurement Locations................................................................................ 6

Reading the Voltages................................................................................................. 7

Re attaching the floor panel and case........................................................................ 8

What you will need

Multimeter

3mm hex driver

Small Screwdriver

Before beginning this process please ensure that all cartridges have been

removed from the machine.

Removing the Jet Wipe

Run the bed to the bottom of the machine using manual move.

Lift Jet wipe out of the machine

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

Voltage Measurement Locations

Depending which stepper motor chip voltage you want to read, you will need to

position your multimeter in different positions of the board. You will need to place a

small screwdriver with one end of the multimeter clipped onto it on the small screw

head labelled TP – and another end of the multimeter will need to be set to ground

on the board.

TP X will measure the voltage for the X axis.

TP Y will measure the voltage for the Y axis.

TP Z will measure the voltage for the Z axis.

TP E1, TP E2 and TP E3 will measure the voltage for print jets 1, 2 and 3.

TP Z

TP Y

TP X

Ground

Reading the Voltages

Plug the CubeX into mains power

Set the multimeter to read DC voltage.

Place the Red (positive) lead onto the desired TP screwhead.

TP E1

TP E2

TP E3

Hold the other end of the multimeter against the ground point.

The multimeter screen will give you your voltage reading.

TP X should read 1.3VDC

TP Y should read 1.6VDC

TP Z should read 1.3VDC

TP E1, E2 and E3 should read 1.1VDC

If your voltage is not correct use the small screwdriver to turn the screwhead in very

small increments measuring the voltage between each turn until it is correct.

Unplug your CubeX from mains power.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

You may now power up your CubeX.

Other manuals for Cubify CUBEX Duo

Table of contents

Other 3D Systems 3D Printer manuals

3D Systems

3D Systems ProJet 7000 User manual

3D Systems

3D Systems ProX 500 User manual

3D Systems

3D Systems ProJet MJP 3600 User manual

3D Systems

3D Systems Cubify CUBEX Duo Operating and safety instructions

3D Systems

3D Systems CubePro User manual

3D Systems

3D Systems ProX 800 User manual

3D Systems

3D Systems ProX SLS 6100 User manual

3D Systems

3D Systems Figure 4 Standalone User manual

3D Systems

3D Systems ProX 950 User manual

3D Systems

3D Systems ProJet 1200 User manual

3D Systems

3D Systems CubePro Assembly instructions

3D Systems

3D Systems CubePro User instructions

3D Systems

3D Systems ProX DMP 100 User manual

3D Systems

3D Systems CUBE User manual

3D Systems

3D Systems CubePro User manual

3D Systems

3D Systems CUBE User manual

3D Systems

3D Systems CubePro User manual

3D Systems

3D Systems ProJet 3500 Max Series User manual

3D Systems

3D Systems ProJet 4500 User manual

3D Systems

3D Systems ProX SLS 6100 User manual

3D Systems

3D Systems ProX 800 User manual

3D Systems

3D Systems ProX DMP 300 User manual

3D Systems

3D Systems Cubify CUBEX Duo Parts list manual

3D Systems

3D Systems CUBE User manual

Popular 3D Printer manuals by other brands

Ultimaker

Ultimaker S5 Material Station installation guide

EcubMaker

EcubMaker TOYDIY quick start guide

AnyCubic

AnyCubic Kossel Plus Modification

ReDeTec

ReDeTec ProtoCycler Operation manual

Kywoo3D

Kywoo3D Tycoon IDEX user manual

CraftBot

CraftBot PLUS PRO user guide

3DGence

3DGence INDUSTRY F340 user manual

HP Jet Fusion 4200 Product Documentation Site Preparation Guide

Rokit

Rokit AEP Series user manual

AnkerMake

AnkerMake M5 user manual

DIYElectronics

DIYElectronics PRUSA I3 ELECTRONICS AND SOFTWARE GUIDE

Ackuretta

Ackuretta FreeShape 120 user manual

LONGER

LONGER LK5Pro manual

Stratasys

Stratasys J850 user guide

MakerBot

MakerBot Replicator user manual

Stratasys

Stratasys FDM Vantage Series user guide

ZYYX

ZYYX Pro II user manual

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Startup guide