Trane Schlage LiNK TZEMT400BB32MAA Assembly instructions

Thermostat

Model TZEMT400BB32MAA

Installation, System Setup, and

Enrollment Instructions

Customer Service: (877) 288-7707

1WARNING

Voltage hazard. Can cause electrical shock or equipment damage. Disconnect power to heating and cooling

equipment before beginning installation.

2Remove the existing thermostat cover from the wall plate. Leave

wires attached.

Consult instructions that came with existing thermostat as needed.

Wall plate

Thermostat cover

The look of your existing

thermostat may vary

Physical Installation and Wiring

The Trane Thermostat is compatible with single and multistage forced air

systems, including:

• Gas furnace systems

• Oil furnace systems

• Electric furnace systems

• Heat pump systems

• Air conditioning systems

The Trane Thermostat may be compatible with some other system

types, including:

• Boiler systems

• Geothermal systems

• Multi-zoned systems

Call (877) 288-7707 to verify compatibility.

The Trane Thermostat is not compatible with the following system types:

• Radiant ﬂoor systems

• Wall heating systems

Also, the Trane Thermostat is not compatible with dual fuel systems

(gas furnace & heat pump combined) without adding a special kit. See

Note below.

• Note about dual fuel systems: This thermostat is not compatible

with dual fuel systems (heating system with both heat pump

and gas furnace), unless the system is controlled with a dual

fuel accessory relay kit. If you are unsure whether your dual fuel

system is controlled with this accessory or if you need a dual

fuel kit, please contact a qualiﬁed heating and cooling contractor.

Tools Needed

1/8”

Bridge requires one 9-Volt battery for

enrollment process. Battery not included.

For professional installation service, instructions, operation guide, and installation video modules, please visit link.schlage.com

Customer Service hours of operation:

•Monday-Friday9.00am-7:00pmEST

•Saturday11:00am-6:00pmEST

•Sunday11:00am-4:00pmEST

To use the remote features of this thermostat, a Schlage LiNKTM account is required. Schlage LiNK™ online setup requires

broadband internet service and router with available port.

If you are unsure about connecting this wire or you do not have any unused wires at the thermostat, contact

Customer Service at (877)288-7707.

Connect a 24 VAC common wire to power the thermostat.

3Determine if your system has a 24 VAC common wire which is required to power the thermostat.

• If your system is a heat pump, skip to step 4.

a. IfyourexistingthermostathasaterminalnamedC,COM,X,orBwithawireconnectedtoit,skiptostep4.

b. If your thermostat does not have that terminal, or does not have a wire connected to it, go to step 3a.

a. Locate all unused (disconnected) wires from the

thermostat wire bundle and write down the colors.

• i24VCommonwireistypically(notalways)colored

blue

Unused wires

Thermostat

wire bundle

b. GotoyourHVACunitandremovethecover(s)toaccess

the24VACfurnacewireterminals.

24 VAC

Furnace

wire

terminals

Furnace

cover

c. Findthe24VACcommonterminalidentiedwiththe

letter C, X, B, or COM.

• This terminal may already have a wire connected to it

but it may not be a wire that goes to the thermostat

24 VAC common

terminal

(C, X, B, or COM)

d. Locate the thermostat wire bundle inside the furnace

panel.

• This wire bundle is routed from the thermostat,

through the walls, and into the furnace panel.

• Thisbundlecanbeidentiedatthefurnaceby

checking the wire colors connected and not connected

and comparing to the wire bundle at the thermostat.

Thermostat

wire bundle

Unused

wires

e. Find a wire from the thermostat bundle that is unused at

the thermostat and at the furnace.

• It is possible that one of the unused wires at the

thermostatwillalreadybeconnectedtothe24VAC

commonterminalatthefurnace.Ifso,gotostep4.

Unused

wire

f. Connecttheunusedwiretothe24VACterminal,then

replace the furnace cover.

• The24VACcommonwireistypically(butnotalways)

blue in color. If the blue wire has been unused, it is

recommended that you use the blue wire.

Connect

wire

Label the wires on your existing thermostat to match terminal names.

• Do not use wire colors to chose labels.The terminal name is what is

important.

a. Locate the wiring labels located in the box with the new thermostat.

b. Lookatwhereeachwireisconnectedtotheexistingthermostatandndthe

letter shown next to that wire terminal.

c. Peel off the matching label and wrap it around each corresponding wire.

Important Notes:

• If you have a short jumper wire between two terminals, remove the jumper

and do not label it. This jumper wire is not required on the new thermostat.

• If you had to connect a new 24 VAC common wire in step 3a, you will use

the “C” label on that wire.

• If you have a W terminal, use the W1/W label on that wire.

• If your thermostat has any terminals with names that do not match any

on the label, write down the terminal names and wire colors for later

reference.

Y G

W1 C

Wire colors and

letters may vary

BCEFGOLY1Y2

X2 TW1

W2 W3

P516-001 Rev. 03/09-a

BCEFGOLY1Y2

X2TW1

W2W3XY

5Remove existing wall plate.

• Note: During this process, make sure that the wires do not pull back into

wall opening.

a. Detach all wires from wall plate.

b. Remove all screws attaching the wall plate to the wall and remove wall plate.

c. See “MERCURY NOTICE” below.

MERCURY NOTICE

When this control is replacing an old control that contains mercury

in a sealed tube, do not dispose of your old control in the trash.

Dispose of properly. Contact your local waste management authority

for instructions regarding recycling and proper disposal of the old

control.

A listing of heating, ventilating and air conditioning wholesalers

that participate in the Thermostat Recycling Corporation’s recycling

program are available at www.thermostat-recyle.org .

Wall plate

6Identify your System Type from the list below.

You will need to check your wire labels to help identify the system type.

CAUTION: EQUIPMENT DAMAGE HAZARD

Improper system type selection can lead to equipment damage or high utility costs. Follow the System Type table

carefully to properly select and setup the control to ensure proper heating and cooling system operation.

Gas Furnace

Single Stage

Gas Furnace

Multi Stage

W2 label = multi stage heating

Y2 label = multi stage cooling

Electric

Furnace Heat

Pump

Electric

Furnace

Single Stage

Electric

Furnace

Multi Stage

W2 label = multi stage heating

Y2 label = multi stage cooling

Heat Pump

Single Stage

Heat Pump

Multi Stage

Does NOT have

W2 or Y2 wire label

Has a

W2 or Y2 wire label

Does NOT have an

O or B wire label

Has an O or B

wire label

Does NOT have

Y2 wire label

Has a

Y2 wire label

START HERE IF

You have a GAS furnace

START HERE IF

You have an ELECTRIC furnace or air handler

Does NOT have

W2 or Y2 wire label

Has a

W2 or Y2 wire label

10 Install new wall plate.

a. Pull wires through hole in center of wall plate.

b. Locate the new wall plate over existing opening.

c. Attach wall plate to wall using two screws provided. Do not overtighten.

7Separate the face of the new thermostat from the wall plate.

Apply pressure at two tabs on top of wall plate to release it.

• NOTE: It is not recommended that this Z-wave thermostat be mounted

onto metal structures. Metal may affect the radio frequency (RF)

communication between the thermostat and the Z-wave signal to the

Schlage Bridge.

8Mark two mounting holes using new wall plate.

a. Pull wires through hole in center of wall plate.

b. Locate the new wall plate over existing opening.

c. Mark two holes with pencil.

d. Use a level to verify that the two holes locations are level.

e. Correct holes locations as needed.

9Prepare two mounting holes.

a. Drill1/16”pilotholesinthetwolocationsthatweremarkedinstep9.Ifmounting

todrywallwithnostudsbehindit,enlargepilotholesto1/8”foranchors.

b. If using anchors, screw them into the holes.

Anchors

24RC

RS2

24C

24RH

W2/O

RS1

Wall plate

Tabs

24RC

RS2

24C

24RH

W2/O

RS1

24RC

RS2

24C

24RH

W2/O

RS1

11 Review the wiring table information.

a. Refer to:

• Table1-IfyoudoNOThaveaheatpump

• Table 2 - If you have a heat pump

b. Select the correct row based upon the thermostat being replaced, and then circle the wire labels you have.

c. Connect your wires as shown in the New Thermostat Terminals row.

Table 1: Gas or Electric

(Single Stage or Multistage)

Themostat Being Replaced Wire Labels

All Brands C

RH W

W2 G

Connects to

New Thermostat Terminals

24COM 24RC 24RH W1 W2/O/B G Y1 Y2

Table 2: Heat Pump

(Single Stage or Multistage)

Themostat Being Replaced Wire Labels

Trane/AmericanStandard

(Weathertron) or York

COM

RH E

AUX

O G Y

Other Brands COM

RH E

AUX

Lennox C

**VR

**V

RH E

AUX

**R

Connects to

New Thermostat Terminals 24COM 24RC 24RH *W1 W2/O/B G Y1 Y2

* ConnecttwowirestotheW1terminal

**Ifyourexistingthermostathasa“V”or“VR”wirelabel,connectthatwireto“24RC”onthenewthermostat,thenconnectthe

wirelabeled“R”to“W2/O/B”onthenewthermostat

Some wire terminals may

not be used

Some wire terminals may

not be used

12 Attach all wires securely to the new thermostat.

Note:Awiremustbeconnectedto“24C”topowerthethermostat.

a. Usetheinformationfromstep11tomatchthewirestothecorrectterminals.

b. Use1/8”bladescrewdrivertosecurewiresinterminals.

CAUTION: EQUIPMENT DAMAGE HAZARD

Improper wiring can lead to equipment damage. Follow the

Terminal Connection information from step 11 carefully to ensure

the control is wired properly. After wires are secure, bare wires

MUST NOT touch each other.

24RC

RS2

24C

24RH

W2/O

RS1

13 If necessary, cut the internal jumper wire (JP1).

24RC

24RH

24RC

24RH

24RC

24RH

Do NOT cut JP1 jumper Cut JP1 jumper

If only one wire is connected

to either 24RC or 24RH

as shown

If wires are connected to

both 24RC and 24RH

as shown

Cutting the JP1 jumper

The jumper is located on back of the thermostat face as shown in the illustration to

the right. Cut the jumper using small diagonal cutters being careful not to damage

the board.

15 Turn power to heating and cooling system back on.

The thermostat display should turn on and begin displaying information. If the thermostat display does not come on, go back

throughtheinstallationstepsandlookforproblems.Payspecialattentiontosteps3,3a,and11.

14 Attach the thermostat face to the wall plate.

a. Tuck wiring ﬂat inside the wall plate.

• It is critical that wires are not bunched together and that they are pressed

ﬂat.

b. Carefully align the face plate to the wall plate while aligning pins into wire

terminals.

c. Once thermostat face is properly aligned, apply pressure at top and bottom of

thermostat face until it is secure.

24RC

RS2

24C

24RH

W2/O

RS1

Wires

pressed flat

JP1

24C

24RH

W2/O

RS1

SHLD

HI-NO

24RC

RS2

SHLD

HI-C

JP1

17 If your System Type is:

Gas Furnace - Single Stage,gotostep19

Gas Furnace - Multistage,performstep18A

Electric Furnace,performstep18B

Heat Pump,performstep18C

• Note: It may be necessary to go back and review step 6 in the installation section to verify the differences between

the system types.

16 Set Time and Date

a. Press the MENU button twice.

MENU MODE FAN RUN

78 68 H

78 C

11:15 PM

MENU button

b. Scroll up or down to User Settings(itistherstoption),

then press the Select button.

c. Scroll up or down to Set Clock(itistherstoption),then

press the Select button.

Done Select

User Settings

Set Clock

Filter Service

Maint Service

Screen Timeout

Scroll

down

Select button

d. Press3or4to highlight the data you want to change.

e. Scroll up or down (+ or -) to make changes.

f. Press the Setbuttonwhenyouarenished.

Scroll

down

Set button

Back

Set Clock

Set

Time 10 :15 PM

Date 3 / 23 / 09

Day Mon

g. Press the Done button twice to exit the menu.

System Settings at Thermostat

Done Select

Menu Selection

User Settings

Usage Graph

ESM Setpoints

ZWave Install

Scroll

down

Select button

Gas Furnace - Multistage Mechanical Settings

a. Press the MENU button twice.

b. Press and hold the two inner buttons for 3 seconds to view

Installer Settings.

c. Scroll down to System Settings and press the Select button.

d. Scroll to Mechanical Settings(itistherstoption),thenpressthe

Select button.

e. Scroll down to 2nd Stage Heat.

f. Press the +button to change the setting to Yfor Yes.

g. If your system also has 2nd stage cooling, scroll down to

2nd Stage Cool and press the +button to change the setting to Y

for Yes.

h. Press the Donebutton4timesandgotostep19.

18A

Electric Furnace Mechanical Settings

a. Press the MENU button twice.

b. Press and hold the two inner buttons for 3 seconds to view

Installer Settings.

c. Scroll down to System Settings and press the Select button.

d. Scroll to Mechanical Settings(itistherstoption),thenpressthe

Select button.

e. Scroll down to Fan Type.

f. Press the +button to change the setting Electric.

• If Single Stage System, press Done4timesandgotostep19.

• If Multistage System, continue with steps “g” through “j”.

g. Scroll down to 2nd Stage Heat.

h. Press the +button to change the setting to Y for Yes.

i. If your system also has 2nd stage cooling, scroll down to

2nd Stage Cool and press the +button to change the setting to Y

for Yes.

j. Press the Donebutton4timesandgotostep19.

18B

18C Heat Pump Mechanical Settings

a. Press the MENU button twice.

b. Press and hold the two inner buttons for 3 seconds to view

Installer Settings.

c. Scroll down to System Settings and press the Select button.

d. Scroll to Mechanical Settings(itistherstoption),thenpressthe

Select button.

e. Scroll to system Type.

f. Press the + button to change the setting to Heat Pump.

g. Scroll down to Fan Type.

h. Press the +button to change the setting Electric.

i. If Coleman, Rheem, or Rudd brand heat pump, scroll to C/O Type

and change to With Heat.

• If Single Stage System, press Done4timesandgotostep19.

• If Multistage System, continue with steps “j” through “n”.

j. Scroll down to 2nd Stage Heat.

k. Press the +button to change the setting to Yfor Yes.

l. Scroll down to 2nd Stage Cool.

m. Press the +button to change the setting to Yfor Yes.

n. Press the Donebutton4timesandgotostep19.

button

MENU MODE FAN RUN

75 76 H

74 C

11:15 PM

Two inner

buttons

Scroll

down

Set buttonSet button

+ button

Done

Mechanical Settings

Select

Type Heatpump

Fan Type Elec

C/O Type w/Cool

2nd Stage Heat N

Test Heating Operation (if your system has heating)

a. Press the MODE button.

b. Scroll to HEATING.

c. Press the Done button to return to the home screen.

d. Turn the temperature up using the scroll up button until the new setpoint is above the room temperature.

e. Verifythattheheatingsystemturnsonandruns.

• Note: It may take approximately 5 minutes for the system to start up after switching from COOLING to

HEATING mode. There is a built in time delay which will not allow the equipment to turn on until it is ready. The

screen will display the word “Wait” until the time delay has ﬁnished.

This concludes the system checkout. If any part of your system fails to come on when performing this checkout

procedure, verify that the correct wires were connected to the wall plate and that each wire is securely attached to the

appropriate terminal. Also go back and verify that you have set up the Mechanical Settings to match your System Type.

Test Fan Operation

a. Press the FAN button.

b. Scroll to ON.

c. Verifythatthesystemfanstartsandmovesair.

d. Press the FAN button.

e. Scroll to AUTO.

f. Press the Done button to return to the home screen.

Test Cooling Operation (if your system has cooling)

a. Press the MODE button.

b. Scroll to COOLING.

c. Press the Done button to return to the home screen.

d. Turn the temperature down using the scroll down button until the

new setpoint is below the room temperature.

e. Verifythattheoutdoorunitandthesystemfancomeonandrun.

Perform System Checkout

CAUTION: Do not run the

air conditioner if the outdoor

temperature is below 55 degrees F.

FAN

button

MODE

button

MENU MODE FAN RUN

75 76 H

74 C

11:15 PM

AUTO AUTO

Sys Off

Run

Table of contents

Other Trane Thermostat manuals

Trane

Trane X13511537-01 User manual

Trane

Trane TCONT802AS32DA User manual

Trane

Trane X13511542010 User manual

Trane

Trane SENS-IN-1D18-HD60D29-4 Assembly instructions

Trane

Trane TCONT600AF11MA User manual

Trane

Trane XT500C Assembly instructions

Trane

Trane XR102 User manual

Trane

Trane BAYSTAT150A Manual

Trane

Trane THT02775 User manual

Trane

Trane ComfortLink II XL1050 User manual

Trane

Trane TZON1050AC52ZAA User manual

Trane

Trane TZEMT500AB32MAA User manual

Trane

Trane TZEMT400BB32MMA User manual

Trane

Trane TCONT402AN32DA Assembly instructions

Trane

Trane Comfort Control XB200 User manual

Trane

Trane XL824 User manual

Trane

Trane TCONT824 User manual

Trane

Trane ProSpace THT03191 User manual

Trane

Trane X39641161-01B Operator's manual

Trane

Trane TCONT 800 Series User manual

Trane

Trane TZEMT500AB32MAA User manual

Trane

Trane BAC-1000 User manual

Trane

Trane BAYSENS019C Assembly instructions

Trane

Trane X13511537-01 Manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide