T&S EC-3100 Series User manual

Installation and

Maintenance

Instructions

EC-3100 Series

ChekPoint

ELECTRONIC FAUCET

DECK-MOUNT & WALL-MOUNT

GOOSENECK, SPOUT & 4”

CENTERSET SENSOR

OPERATED

Limited One Year Warranty

T&S warrants to the original purchaser (other

than for purposes of resale) that such product is

free from defects in material and workmanship for

aperiodofone(1)yearfromthedateofpurchase.

Duringthisone-yearwarrantyperiod,iftheproduct

is found to be defective, T&S shall, at its options,

repairand/orreplaceit. Toobtainwarrantyservice,

productsmust bereturned to...

T&SBrass andBronze Works,Inc.

Attn: WarrantyRepair Department

2Saddleback Cove

TravelersRest, SC 29690

Shipping, freight, insurance, and other

transportation charges of the product to T&S and

the return of repaired or replaced product to the

purchaser are the responsibility of the purchaser.

Repair and/or replacement shall be made within a

reasonabletimeafterreceiptbyT&Softhereturned

product. ThiswarrantydoesnotcoverItemswhich

have received secondary ¿nishing or have been

altered or modi¿ed after purchase, or for defects

caused by physical abuse to or misuse of the

product,or shipmentof theproducts.

Any express warranty not provided herein, and

any remedy for Breach of Contract which might

arise, is hereby excluded and disclaimed. Any

implied warranties of merchantability or ¿tness

for a particular purpose are limited to one year in

duration. Under no circumstances shall T&S be

liable for loss of use or any special consequential

costs,expenses ordamages.

Some states do not allow limitations on how

long andimplied warrantylasts or the exclusionor

limitation of incidental or consequential damages,

sotheabovelimitationsorexclusionsmaynotapply

toyou. Speci¿crightsunderthiswarrantyandother

rightsvary fromstate tostate.

P/N: 098-016361-45 Rev.6

Date: 04-22-14

Drawn: TEH

Checked: GEF 05-07-14

Approved: JHB 05-07-14

EC-3100

EC-3101

EC-3102

EC-3103

EC-3106

Exploded View

EC-3100

Exploded View

EC-3101

Exploded View

EC-3102

6 7

Exploded View

EC-3103

Exploded View

EC-3106

Part Number Guide

EC-3100 & EC-3101 Electronic Faucets

1 Aerator, Vandal Resistant B-0199-06

2 Adapter for Non-Splash Aerator 044A

3 O-Ring 006575-45

4 Angled Sensor w/ Cable 017195-45

5 Inlet Hose for use with EC-3100

1/2” NPSM-F x 1/4” NPSM-F x 18” Long 016297-45

5 Inlet Hose for use with EC-3101

1/2” NPSM-F x 3/8” NPSM-F x 30” Long 016325-45

6 Electronic Module 016647-45

7 A/C Transformer 5EF-0002

8 Manual Mixing Valve 5EF-0006

9 Supply Hose, 9/16-24 UN Female x 1/2” NPSM 5EF-0005

10 Vandal Resistant Key Q015425-45

EC-3102 & EC-3103 Electronic Faucets

1 Aerator, Vandal Resistant, 2.2 GPM 016355-45

2 Angled Sensor w/ Cable 017195-45

3 Inlet Hose, Faucet, 1/2” NPSM-F x 1/4” NPSM-F 016297-45

4 Electronic Module 016647-45

5 A/C Transformer 5EF-0002

6 Manual Mixing Valve 5EF-0006

7 Supply Hose, 9/16-24 UN Female x 1/2” NPSM 5EF-0005

8 Vandal Resistant Key Q015425-45

EC-3106 Electronic Faucet

1 ChekPoint Module (Blue) with Bypass Tee 017493-45

2 A/C Transformer 5EF-0002

3 Manual Mixing Valve 5EF-0006

4 Supply Hose, 9/16-24 UN Female x 1/2” NPSM 5EF-0005

5 VR Aerator with Key B-0199-09

6 Vandal Resistant Key Q015425-45

General Instructions

Important:

· ALL ELECTRICAL WIRING IS TO BE

INSTALLED IN ACCORDANCE WITH

NATIONAL/LOCAL CODES AND REGULA-

TIONS.

· ALL PLUMBING IS TO BE INSTALLED IN

ACCORDANCE WITH

APPLICABLE CODES AND REGULATIONS.

· USE APPROPRIATE PRECAUTIONS

WHILE CONNECTING TRANSFORMER TO

120 VAC POWER SOURCE.

· DO NOT PLUG TRANSFORMER INTO

POWER SOURCE (RECEPTACLE) UNTIL

ALL WIRING IS COMPLETED.

· FLUSH ALL WATER LINES UNTIL WATER

IS CLEAR BEFORE CONNECTING FAUCET

TO SUPPLY STOPS.

Tools Required For Installation of

Faucets

· 8” (200mm) adjustable wrench

· 1/8” hex key wrench

· Basin wrench

· Slotted screwdriver, 3/16”

· Phillips head screwdriver, #1

· Pliers

Prior to Installation:

Prior to installing the T&S ChekPoint

Series Faucet, install the items listed on

next column. Also, refer to Figure 1.

· Provide electrical receptacle within

approximately 6’ from sink for plug-in

transformer — 120 VAC, 2 amp service

for each plug-in transformer used.

· Scrub or wash-up sink

· Drain line

· Hot and cold water supply lines

Mixing Valve

When installing the faucet with the mix-

ing valve the Installation Instructions

MUST be followed.

Figure 1

Deck-Mount

Wall-Mount

General Instructions

Installation of ChekPoint Faucets

The T&S ChekPoint Sensor Operated Faucet is a pre-tempered faucet. A mixing valve

(supplied) must be used in conjunction with the faucet. Water temperature can be

controlled by adjusting the mixing valve.

Install Faucet Assembly (Figures 2A, 2B, 2C and 2D)

TO MOUNT ON A SURFACE UP TO 1” (25mm) THICK

Insert faucet cable and spout shank through base gasket and then through the mount-

ing hole of scrub or wash-up sink. Secure using lockwasher and nut supplied.

Note: T&S Brass does

NOT supply hardware

necessary for mounting

the faucet on surfaces

thicker than 1” (25 mm)

thick.

Figure 2A

Wall-Mount

(Front View)

Figure 2B

Single Hole Deck-Mount

(Front View)

(Back View)

(Bottom View)

(Front View)

Figure 2C

4” Deck-Mount

(Bottom View)

Figure 2D

EC-3106

General Instructions

OPTIONAL ANTI-ROTATION

FEATURE

Wall-Mount Model: EC-3101

(Figure 2D)

Note: The anti-rotation feature uses a set

screw to anchor the faucet in the vertical

position and is intended for use ONLY on

stainless steel sinks.

Use the mounting hole diagram or fau-

cet base gasket as a template by placing

it in position over the faucet mounting

hole. Mark the stainless steel mounting

surface at the center of the small notch

at the bottom of the base gasket. Drill a

9/32” (7.14 mm) diameter hole through

the stainless steel mounting surface.

Extend the 1/4-20 set screw installed in

the back of the faucet body by unscrew-

ing it (counterclockwise) with a 1/8” hex

key wrench. Unscrew it far enough that

it protrudes past the base gasket and

into the 9/32” drilled hole. Assemble

the washer and nut to secure the faucet

in place.

OPTIONAL ANTI-ROTATION

FEATURE

Deck-Mount Models: EC-3100 &

EC-3102

(Figure 2E)

Note: The anti-rotation feature uses a pin

to anchor the faucet in position and is

intended for use ONLY on stainless steel

sinks.

Use the mounting hole diagram or the

faucet base gasket as a template by

placing it in position over the faucet

mounting hole. Mark the stainless steel

mounting surface at the center of the

small hole at the bottom of the base

gasket. Drill a 5/32” (4 mm) diameter

hole through the stainless steel

mounting surface. Install the faucet

aligning the pin with the small hole.

Assemble the washer and nut to secure

the faucet in place.

Note: The pin can be removed with

pliers if not needed.

Figure 2D

Figure 2E

EC-3101 MOUNTING HOLE

DIAGRAM

Ø1” THRU

1 9/32”

Ø9/32”

For Anti-Rotation

EC-3100 & EC-3102

MOUNTING HOLE

DIAGRAM

Ø1” THRU

Ø5/32”

For Anti-Rotation

1”

This manual suits for next models

Table of contents

Popular Plumbing Product manuals by other brands

Weka

Weka 506.2020.00E ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS

Kohler

Kohler K-6228 Installation and care guide

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Operator's manual

American Standard

American Standard DetectLink 6072121 manual

Uponor

Uponor Contec TS Mounting instructions

Pfister

Pfister Selia 49-SL Quick installation guide

Fortis

Fortis VITRINA 6068700 quick start guide

Fortis

Fortis MILANO 78211JS installation instructions

Kohler

Kohler K-12183 Homeowner's guide

Maxxus

Maxxus MX-M206-01 instruction manual

Moen

Moen 5922 Series installation instructions

Viega

Viega Prevista Pure 8512 Instructions for use

Kohler

Kohler Centerset K-15240 Homeowner's guide

Viega

Viega Prevista Dry 8522.33 Instructions for use

Sanela

Sanela Lema SLP 59RB Instructions for use

Elkay

Elkay EDF15AC Installation, care & use manual

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Instructions for use/assembly instructions

baliv

baliv WT-140 manual