Siemens RDD100.1RF User manual

1/2 Operating Instructions CB1B1431en_01 / 2013-07-05 Siemens Building Technologies

Operating Instructions

RDD100.1RF

The RDD100.1RF consists of a wireless room thermostat RDD100.1RF which operates in connection with an RDE-MZ6

receiver. These units allow you to set the ideal room temperature at the time you want.

RDD100.1RF

1 Display

Indicates that batteries need to be replaced

Comfort mode

Economy mode

Frost protection (heating) active

Room temperature, setpoint, etc.

Room temperature in degrees Fahrenheit

Room temperature in degrees Celsius

Button lock activated

Display of zone (default = 1)

Heating On

Current room temperature

2 Change operating mode

3 Decrease value

4 Increase value

5 Battery holder

RDE-MZ26

To be purchased separately

Do you want to lock the buttons?

Press and hold for at least 7 seconds to activate a button lock. Repeat to unlock.

The unit operates normally when the buttons are locked, but no changes can be made.

Do you want to change the operating mode?

The room thermostat provides Comfort mode and Economy mode . Changeover between the operating modes can be

made manually by pressing .

Comfort mode is a permanent (24 h) selection of Comfort. Select this mode when you want to maintain permanently the Comfort

temperature. It is used during occupancy periods, for example.

Economy mode is a permanent (24 h) selection of Economy. Select this mode when you want to maintain permanently the

Economy temperature. It is used during non-occupancy periods (e.g. at night).

Note:

Frost protection is a function always active in the background. As soon as the room temperature falls below 5 ºC, the unit

automatically activates heating .

Energy saving tips without loss of comfort

•Use Economy mode during longer periods of non-occupancy

2/2 Operating Instructions CB1B1431en_01 / 2013-07-05 Siemens Building Technologies

Are your rooms too warm/too cold?

–

Press +or –to increase or decrease the room

temperature setpoint in increments of 0.5 °C/1 °F.

Proceed as follows:

•Press +or –to change the setpoint temporarily.

Press to save the setting or wait for the

program to exit automatically

•To permanently change the temperature

setpoints, use parameters P05 and P07.

To lock the setpoints, use parameters P06 and

P08

Does symbol appear on the display?

Symbol is displayed when the batteries are low. Replace

them with 2 new alkaline batteries type AAA. Proceed as

follows:

•Get 2 new alkaline batteries type AAA

•Remove the battery holder and then the batteries. Insert the

new batteries and, within 1.5 minutes, replace the battery

holder

•Ensure the exhausted batteries are disposed of correctly, in

compliance with environmental requirements

Do you want to pair transmitter and receiver?

Please refer to the instructions that come with the RDE-MZ6.

Do you want to change parameters?

–

If you want to change control parameters, proceed as

follows:

•Press +and –simultaneously for 5 seconds

•Release them and parameter P02 is displayed

•Press +or –to scroll to the parameter that needs

to be changed

•Press to select the parameter

•Press +or –to change the value

•Press to confirm and save the changed value

•Select and change other parameters

•The program automatically returns to the normal

screen after a timeout

Parameter list

Parameter

no.

Description Setting range (default)

P02 Selection of °C or °F 1 = °C (default)

2 = °F

P03 Standard temperature

display

1 = room temperature

(default)

2 = setpoint

P04 Temperature sensor

calibration

-3…3 °C

Step 0.5 °C

(-6…6 °F, step 1 °F)

Default: 0 °C

P05 Comfort setpoint 5…35 °C, step 0.5 °C

(41…95 °F, step 1 °F)

Default: 20 °C, 68 °F

P06 Comfort setpoint lock 0 = OFF (default)

1 = ON locked according

to setting in P05

P07 Economy setpoint 5…35 °C, step 0.5 °C

(41…95 °F, step 1 °F)

Default: 16 °C, 61 °F

P08 Economy setpoint lock 0 = OFF (default)

1 = ON locked according

to setting in P07

P09 Buzzer 0 = OFF

1 = ON (default)

P10 Show frost protection

icon

0 = OFF (default)

1 = ON and always on at 5 ºC

P19 Sequential number of

room unit

0 = no display of zone

(RF off)

1 = zone number 1

(for standard RF) (default)

6 = zone number 6

P20 RF learn 0 = OFF (default)

1 = ON

P21 Scanning rate for the

capacitive buttons

Note: Shorter

scanning rate means

shorter battery life

0.2 = 0.25 s

0.5 = 0.5 s

1.0 = 1.0 s (default)

1.5 = 1.5 s

P22 Reload factory

settings

0 = OFF (default)

1 = reload

P23 Software version

information

No adjustment possible

Other manuals for RDD100.1RF

This manual suits for next models

Table of contents

Other Siemens Thermostat manuals

Siemens

Siemens RDE20.1 User manual

Siemens

Siemens RDY2000 User manual

Siemens

Siemens RDG400KN Operator's manual

Siemens

Siemens REV17 Series User manual

Siemens

Siemens RDJ100 User manual

Siemens

Siemens raa20 series User manual

Siemens

Siemens QMX3.P37 User manual

Siemens

Siemens RDG100 Series User manual

Siemens

Siemens BRTRF User manual

Siemens

Siemens RDF300 Series Operator's manual

Siemens

Siemens QFA1000 User manual

Siemens

Siemens RDS110.R User manual

Siemens

Siemens RDJ10 User manual

Siemens

Siemens RDH100RF/SET User manual

Siemens

Siemens RDD100 Series User manual

Siemens

Siemens RDF301 User manual

Siemens

Siemens RDS110.R User manual

Siemens

Siemens RAB20 Series Owner's manual

Siemens

Siemens RDS110 User manual

Siemens

Siemens RAA Series Owner's manual

Siemens

Siemens Powers TH 188 Owner's manual

Siemens

Siemens REV34 User manual

Siemens

Siemens RDF302 User manual

Siemens

Siemens RDG100KN User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide