Siemens POLYMOBIL Plus Installation manual

POLYMOBIL Plus

English

Print No.: SPR8-125.034.01.03.02 Doc. Gen. Date: 01.00

Replaces: SPR8-125.034.01.02.02

The reproduction, transmission or

use of this document or its contents

is not permitted without express

written authority. Offenders will be

liable for damages. All rights,

including rights created by patent

grant or registration of a utility

model _or_design,_are_reserved.

Start-up Instructions

POLYMOBIL Plus SPR8-125.034.01 Page 2 of 4 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

0 - 2 Revision

Chapter Page Revision

0all03

1all03

2all03

3all03

4all03

5all03

6all03

Contents 0 - 3

Siemens AG SPR8-125.034.01 Page 3 of 4 POLYMOBIL Plus

Medical Engineering Rev. 03 01.00 TD SD 24

1 _______Requirements__________________________________________________ 1 -1

Specially marked text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -1

Tools and measurement devices required. . . . . . . . . . . . . . . . . . . . . . . . 1 -1

Safety information and protective measures . . . . . . . . . . . . . . . . . . . . . . 1 -2

Important start-up information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -4

Replacing damaged or missing screws . . . . . . . . . . . . . . . . . . . . . . . . . 1 -5

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -5

2 _______Unpacking ____________________________________________________ 2 - 1

3 _______Function checks _______________________________________________ 3 - 1

Checking the nominal line voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

Attaching the warning label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

Checking the controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2

Checking the counterbalance system . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3

Readjusting the counterbalance system with accessories attached . . . . . . . . . . 3 - 3

Checking the controls on the double-slot diaphragm . . . . . . . . . . . . . . . . . . 3 - 4

Checking the exposure release with high voltage . . . . . . . . . . . . . . . . . . . . 3 - 4

Checking the exposure control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5

Custom programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5

Checking coincidence of light and radiation fields. . . . . . . . . . . . . . . . . . . . 3 - 5

4 _______Final procedures _______________________________________________ 4 - 1

Protective conductor measurement . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1

Equivalent leakage current measurement . . . . . . . . . . . . . . . . . . . . . . 4 - 1

5 _______Test protocol __________________________________________________ 5 - 1

POLYMOBIL Plus Start-up protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1

6 _______Changes to previous version _____________________________________ 6 - 1

Page

0 - 4 Contents

POLYMOBIL Plus SPR8-125.034.01 Page 4 of 4 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

This page intentionally left blank.

1 - 1

Siemens AG SPR8-125.034.01 Page 1 of 6 POLYMOBIL Plus

Medical Engineering Rev. 03 01.00 TD SD 24

Specially marked text 1

Tools and measurement devices required 1

All tools and measurement devices with the exception of the standard service kit

are specified in the ARTD / Part 3.

•Standard service kit

•Protective conductor test meter

•Equivalent leakage current meter

•Digital multimeter.

"Warnings" are information provided with special emphasis when

there is

the potential for personal injury to the operator or patient.

"Cautions" are information provided with special emphasis when

there is

the potential for damage to the equipment.

"Notices" are information provided with special emphasis to facil-

itate

proper use of the equipment or proper execution of a procedure.

WARNING

CAUTION

NOTICE

Requirements 1

POLYMOBIL Plus SPR8-125.034.01 Page 2 of 6 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

1 - 2 Requirements

Safety information and protective measures 1

•When performing service work and tests, adhere to:

- the product-specific safety information in the document,

- the safety information in RA0-000.012.... in the Register of

the POLYMOBIL Plus binder,

- as well as the general safety information contained in

part 2 of the ARTD.

•Tests and adjustments that must be performed with radiation

ON, are identified by the radiation warning symbol .

Radiation protection must be worn during these types of

adjustments.

CAUTION

Requirements 1 - 3

Siemens AG SPR8-125.034.01 Page 3 of 6 POLYMOBIL Plus

Medical Engineering Rev. 03 01.00 TD SD 24

When working with the system open, there is danger of

! Electric shock !

•The capacitor bank can still be charged.

Do not attempt to work on the system while this condition exists.

•After switching off the system, approximately 450 VDC (350 VDC

for Serial-No. < 10100) may still be present in the system; even

after disconnecting the line voltage plug. Within 10 minutes this

voltage will drop to approximately 10 V.

•Always measure the actual voltage present with the DVM at test

points -VCC and +VCC on the D960 inverter board or (more

accessible) on the D970 capacitor board at the + connection

point of capacitor C3 and on the right side of fuse F3 (refer to

Fig. 1).

•LED’s V1 ... V10 on D 970 go out at a significantly higher voltage

level and therefore they are not reliable safety indicators.

•If a fuse on the D 970 has responded, high voltage may still be

present at the affected capacitor even after a prolonged period

of time.

•The capacitor discharging circuit utilizes the D 925 board and

relays CS and LS. If connector X3 or X9 on D 925 or D 950 are not

inserted or there is a defect in the circuit, the C-bank will not

discharge.

This can cause life-threatening voltage to be present in the

system even after a prolonged period of time.

•Refer also to the POLYMOBIL Plus Service instructions

RXR8-120.061.01... "Replacing the capacitor bank".

Fig. 1

VCC

C1R3R4

WARNING

POLYMOBIL Plus SPR8-125.034.01 Page 4 of 6 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

1 - 4 Requirements

•Connect the POLYMOBIL Plus only to a line voltage supply (receptacle) that complies

with the requirements of VDE 0107 or corresponds to the local national standards.

•Disconnect the POLYMOBIL Plus at the line voltage OFF switch on the operating

console and disconnect the line voltage plug prior to any service work.

•Remove or insert boards with the generator switched OFF only; observe

ESD guidelines when handling boards.

Important start-up information 1

•After completion of the start-up procedure, the POLYMOBIL Plus which has been

completely tested and adjusted at the factory, is ready to operate.

•The POLYMOBIL Plus can be connected to nominal line voltages from 110 V AC through

230 V AC (± 10%) and automatically self-adjusts to the existing power line voltage.

•After start-up, country-specific tests are to be performed, if required;

e.g. acceptance test according to RöV (Germany - X-ray ordinance).

Acceptance test according to RöV (Germany):

Required measurements can be partially transferred from the test protocol provided.

The following values are measured at the factory and recorded in the test certificate:

- Light localizer brightness

- Filter values - visual check

- Coincidence of light field and radiation field

- X-ray tube voltage accuracy

- mAs value check

- Reproducibility of the radiation

•The test / measurement values identified by the " " symbol should be entered in the

start-up protocol located at the end of these instructions.

•Adhere to the fuse ratings for the on-site receptacle:

- 16A slow-blow (on-site) at 110 ±10% or 230V ±10% line voltage

•The line voltage cable of the POLYMOBIL Plus is supplied with a

(Schuko) safety plug.

Install line voltage plugs that comply with the local standards, if

required.

CAUTION

Requirements 1 - 5

Siemens AG SPR8-125.034.01 Page 5 of 6 POLYMOBIL Plus

Medical Engineering Rev. 03 01.00 TD SD 24

Replacing damaged or missing screws 1

•As specified in the installation drawings, damaged or missing screws may only be

replaced by steel screws conforming to DIN 267 and having the specified tensile

strength.

Cleaning 1

•The unit must always be switched off or disconnected before cleaning. Use only water to

clean the unit or a lukewarm solution consisting of water and a household cleaning

agent.

•Do not use abrasive cleaning agents or organic solvents such as benzine, alcohol or spot

remover.

•Do not spray water on the unit.

•For additional information, refer to the Operating Instructions "Cleaning/Disinfecting".

All Allen screws must have a tensile strength rating of 8.8.

CAUTION

POLYMOBIL Plus SPR8-125.034.01 Page 6 of 6 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

1 - 6 Requirements

This page intentionally left blank.

Other manuals for POLYMOBIL Plus

Table of contents

Other Siemens Medical Equipment manuals

Siemens

Siemens ACUSON X300 User manual

Siemens

Siemens MAGNETOM Avanto User manual

Siemens

Siemens ARCADIS Varic Installation manual

Siemens

Siemens Uroskop ACCESS User manual

Siemens

Siemens MAMMOMAT 3000 User manual

Siemens

Siemens MOBILETT Plus HP User instructions

Siemens

Siemens MAMMOMAT NovationDR Manual

Siemens

Siemens MAMMOMAT 1000 Nova Operating and maintenance instructions

Siemens

Siemens MULTIMOBIL 5C User manual

Siemens

Siemens 25 User manual

Siemens

Siemens SOMATOM Scope User manual

Siemens

Siemens ARCADIS Orbic Installation manual

Siemens

Siemens SIREMOBIL Compact User instructions

Siemens

Siemens SOMATOM Sensation 16 User manual

Siemens

Siemens Drager Medical Fabius GS Assembly instructions

Siemens

Siemens MAMMOMAT Novation DR User manual

Siemens

Siemens MULTIMOBIL 10 User manual

Siemens

Siemens MTCO 1324 User manual

Siemens

Siemens ARCADIS Avantic Installation manual

Siemens

Siemens ACUSON S Series User manual

Siemens

Siemens ARCOSKOP Operating and maintenance instructions

Siemens

Siemens ACUSON Freestyle User manual

Siemens

Siemens MULTI-ECHO EPI 4A21 User manual

Siemens

Siemens POLYMOBIL III Installation manual

Popular Medical Equipment manuals by other brands

TekTone

TekTone Tek-CARE160 Installation and operation manual

NeuroMetrix

NeuroMetrix Quell 2.0 user manual

AMT

AMT XLR8 Quick reference guide

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 instruction manual

EDAN

EDAN SONOTRAX Pro user manual

Restorative Therapies

Restorative Therapies RT300 Service guide

Gendex

Gendex Expert DC installation manual

Dexcowin

Dexcowin ADX4000W user manual

Libelium

Libelium MySignals user manual

Acelity

Acelity V.A.C.ULTA 4 user manual

Caputron

Caputron ActivaDose II tDCS quick start guide

FujiFilm

FujiFilm Sonart Features

Plinth 2000

Plinth 2000 93CDT Service manual

GE SENOGRAPHE 800T Operator's manual

GE Definium 5000 Operator's manual

Kanmed

Kanmed GE-1380 user manual

Huntleigh

Huntleigh FD1 Instructions for use

Stryker

Stryker SPR Plus Operation manual