RephiLe RephiDuo P Pack TL1 User manual
Page 1of 3
INSTALLATION GUIDE
RephiDuo P Pack TL1 with RO cleaning media
RephiLe Catalogue Number:
RR500CPC1
Comparable Millipore Part Number:
PR0GTLCS1
Suitable Millipore Systems:
RiOs 30 - 200
Elix 20 – 100. Elix Clinical
This product is a comparable to the corresponding Millipore cartridges. Please refer to
Millipore’s User Manual for a detailed instruction on installation.
A brief description of the installation process is described below:
1. Place the system into Standby by pressing the STANDBY button for about 2 seconds
2. Press the MAINTENANCE button
3. Press the EXCH PROGARD PACK button for 2 seconds to get the system into
depressurize and purge mode. System will purge for 12 seconds during which time the
pump will operate.
PRODUCTION 9 5%
REJ 9 8. 0%
DATA
STANDBY
STANDBY
SETUP
MAINTENANCE
PRODUCTION
MAINTENANCE DATA
EXCH PROGARD PACK
STANDBY
SETUP
MAINTENANCE
PRODUCTION
PURGE
PROGARD TL PACK
PLEASE WAIT…
CANCEL
MAINTENANCE DATA
EXCH PROGARD PACK
Page 2of 3
4. Wait till the purge completes. The system is now ready to have cartridge replaced.
4.1 Lift up the cartridge Locking Handle as shown in the
picture.
4.2 Gently pull the used cartridge out of the system. Make
sure no old O-rings are left on the four ports of the
water system.
4.3 Take o u t t h e n e w cartrid g e ; remove the four blue
protective caps on the cartridge nozzles. Make sure
each O-ring inside nozzles is firmly pushed in and
seated flat.
4.4 Install the cartridge onto the system with the
THIS END UP arrow on the cartridge pointing up and all
four nozzles are firmly pushed in.
Note: Cartridge is directional. It must be installed
with the THIS SIDE UP arrow pointing up.
PURGE
PROGARD TL PACK
PLEASE WAIT…
CANCEL
PLEASE REMOVE
PROGARD TL PACK
CANCEL
Page 3of 3
4.5 Push down the cartridge Locking Handle until it is
securely locked.
If the pin does not lock all the way down, the cartridge
probably has not been pushed all the way into ports.
Reinstall the cartridge if necessary till the lock pin is
fully locked.
5 Press the CONTINUE a few times till the system goes into cleaning mode
Note: If you have a Storage Reservoir with a Vent Filter, the LCD will remind you to
change the Vent Filter at this time. You can press the CONTINUE button one
more time to skip it.
System goes into Cleaning for 20 minutes. Once the cleaning cycle completes, system
will produce water automatically.
RephiSolo, RephiDuo and RephiQuatro are trademarks of RephiLe Bioscience, Ltd.
© 2010. RephiLe Bioscience, Ltd. All rights reserved.
All other trademarks are trademarks of their respective manufacturers.
PLEASE EXCHANGE
VAET FILTER
CONTINUE
TEST FEED PRESS
PLEASE WAIT…
SYSTEM CLEANING
R. TIME: 20 min
This manual suits for next models
1
Other RephiLe Water Filtration System manuals
Popular Water Filtration System manuals by other brands
Wisy
Wisy LineAir 100 Installation and operating instructions
Schaffner
Schaffner Ecosine FN3446 Series User and installation manual
Pentair
Pentair FLECK 4600 SXT Installer manual
H2O International
H2O International H20-500 product manual
Renkforce
Renkforce 2306241 operating instructions
Neo-Pure
Neo-Pure TL3-A502 manual
