Remii WM-50-XS Owner's manual

INSTALLATION AND OPERATION INSTRUCTIONS FOR

WM-50-XS

WM-60-XS

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE

TABLE OF CONTENTS

IMPORTANT INSTRUCTIONS

.........................................................................................................................................

UNPACKING AND TESTING APPLIANCE

...................................................................................................................

GROUNDING APPLIANCE

...............................................................................................................................................

LOCATING THE FIREPLACE

...........................................................................................................................................

M-50-XS

.............................................................................................................................................................................

M-60-XS

.............................................................................................................................................................................

INSTALLATION- ALL MOUNT

............................................................................................................................... .....

INSTALLATION- BUILT-IN

...........................................................................................................................................

HARD- IRE INSTALLATION

......................................................................................................................................

MEDIA OPTIONS

..............................................................................................................................................................

DECORATIVE MEDIA INSTALLATION

......................................................................................................................

OPERATION

.......................................................................................................................................................................

MANUAL OPERATION

...................................................................................................................................................

REMOTE CONTROL OPERATION

................................................................................................................................

INSTALLING ALL THERMOSTAT

...........................................................................................................................

REPLACEMENT PARTS

..................................................................................................................................................

EXPLODED VIE

............................................................................................................................................................

TROUBLE SHOOTING

.....................................................................................................................................................

SERVICE HISTORY

..........................................................................................................................................................

ARRANTY

......................................................................................................................................................................

Please read and carefully follow all of the instruction found in this manual. Please pay

special attention to the safety instructions provided in this manual. The instructions included

here will assure that you have many years of dependable and enjoyable service from your

this product.

IMPORTANT INSTRUCTIONS

1. Read all instructions before installing or using this heater.

2. Keep combustible materials such as furniture pillows bedding papers clothes and

curtains at least 3 feet from the front sides and rear of the heater.

3. Always unplug heater when not in use.

4. Do not operate the fireplace if it has a damaged cord or plug after it has

malfunctioned or if the unit has been dropped or damaged in any way.

5. Do not use the heater outdoors.

6. Do not run the cord under carpeting. Do not cover the cord with throw rugs runners

or anything else. Arrange the cord away from traffic areas where it could not be

tripped over.

7. To disconnect the heater turn the controls to "OFF" before removing the plug from

the outlet.

8. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as

this may cause an electric shock fire or damage to the heater.

9. To prevent a possible fire do not block air intakes in any manner.

10. A heater has hot and arcing or sparking parts inside. Do not use it in areas where

gasoline paint or flammable liquids are used or stored.

11. Use this heater only as described in this manual. Any other use not recommended

by the manufacturer may cause fire electric shock or injury.

12. Avoid the use of an extension cord the extension cord will overheat and cause a fire.

This heater is not to be used with an extension cord.

13. Always use properly grounded fused and polarized outlets.

14. Always use ground fault protection where it is required by electrical codes.

15. Always disconnect the power before performing any cleaning maintenance or

relocation of the heater.

16. To prevent a possible fire do not burn wood or other materials in this heater.

17. To prevent electric shock or fire always use a certified electrician should new

circuits or outlets be required.

18. When transporting or storing the heater keep it in a dry place free from excessive

vibration.

19. This appliance should not be modified under any circumstances.

20. Packaging material should be kept away from children and be disposed of in a safe

manner. Plastic bags are not toys and should be kept away from children and

infants.

21. Do not use this heater in small rooms when they are occupied by persons not

capable of leaving the room on their own unless constant supervision is provided.

22. If the glass is damaged do not use the heater in order to avoid a hazard.

23. Do not leave children unsupervised where heater is turned on.

24. CAUTION Some parts of this product can become very hot and cause burns.

Particular attention has to be given where children and vulnerable people are

present.

25. This appliance can be used by children aged from 8 years and above and persons

with reduced physical sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision.

Cautions

Do’s



Always install the heater in accordance with this guide. If in doubt obtain

expert advice.



Always make sure the electrical socket is accessible and located adjacent

to but not above the heater.



Always disconnect the heater from the electrical supply before moving it or

carrying out cleaning maintenance.



Always make sure the heater is firmly secured to prevent it from being

tipped over.



Always use a fireguard when young children and infirm persons can come

into contact with the heater.

Don’ts



Never leave children unsupervised in a room where the heater is ON and

unguarded.



Never obstruct or cover the fan outlet or force items into heater openings.



Never install or use the heater anywhere where water is in use i.e.

Bathroom Kitchens Shower Rooms and Swimming Pool etc.



Never use aerosols or steam cleaners on or around the heater.



Never route the mains supply cable under carpet etc.



Never install the heater close to curtains or combustible materials.



Never use the heater to dry clothes etc.



Never sit or stand on the heater.



Never use with a timer or any other device that switches the fire on

automatically.

UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box.

ior to installing the appliance test to make sure the appliance operates properly by plugging

the power supply cord into a 120 Volt grounded outlet.

Test all aspects of its operation (manual switches remote and heater) to make sure all

components are op

erating correctly.

As with most electronic devices your new electric fireplace has been designed to operate at

temperatures between 5 ℃ (41

℉

fireplace to reach room temperature before turning it o

NOTE: Th r may b trac of odor during th first f w minut s of initial us . This is

harml ss, normal and will n v r occur again.

GROUNDING APPLIANCE

This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as

shown i

n (C) is available for connecting three

receptacles. The green grounding lug extending from the adapter must be connected to a

permanent ground such as a properly grounded outlet box. The adapter should not be used if

three-

slot grounded receptacle is available.

To disconnect appliance turn controls to off then remove plug from outlet.

LOCATING THE FIREPLACE

Plan where to locate and frame the fireplace. This will save time and money later whe

install the fireplace. Before installation consider the following:

Where the fireplace is located must allow for wall and ceiling clearances

Consider a location where the fireplace screen will not be exposed to direct sunlight from

windows or doors.

A 15 ampere 120 Volt 60 Hz branch circuit with proper ground must be available at the

location. Preferably a dedicated branch circuit should be provided to avoid circuit breakers

to trip of fuses to blow.

UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box.

ior to installing the appliance test to make sure the appliance operates properly by plugging

the power supply cord into a 120 Volt grounded outl

et.

Test all aspects of its operation (manual switches remote and heater) to make sure all

erating correctly.

As with most electronic devices your new electric fireplace has been designed to operate at

℉

) and 35 ℃ (95℉

). During the cold winter months allow the

fireplace to reach room temperature before turning

it on.

NOTE: Th r may b trac of odor during th first f w minut s of initial us . This is

harml ss, normal and will n v r occur again.

This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as

n (C) is available for connecting three

blade grounding type plugs to two

receptacles. The green grounding lug extending from the adapter must be connected to a

permanent ground such as a properly grounded outlet box. The adapter should not be used if

slot grounded receptacle is available.

To disconnect appliance turn controls to off then remove plug from outlet.

LOCATING THE FIREPLACE

Plan where to locate and frame the fireplace. This will save time and money later whe

install the fireplace. Before installation consider

the following:

Where the fireplace is located must allow for wall and ceiling clearances

Consider a location where the fireplace screen will not be exposed to direct sunlight from

A 15 ampere 120 Volt 60 Hz branch circuit with proper ground must be available at the

location. Preferably a dedicated branch circuit should be provided to avoid circuit breakers

ior to installing the appliance test to make sure the appliance operates properly by plugging

Test all aspects of its operation (manual switches remote and heater) to make sure all

As with most electronic devices your new electric fireplace has been designed to operate at

). During the cold winter months allow the

NOTE: Th r may b trac of odor during th first f w minut s of initial us . This is

This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as

blade grounding type plugs to two

-slot

receptacles. The green grounding lug extending from the adapter must be connected to a

permanent ground such as a properly grounded outlet box. The adapter should not be used if

To disconnect appliance turn controls to off then remove plug from outlet.

Plan where to locate and frame the fireplace. This will save time and money later whe

n you

Where the fireplace is located must allow for wall and ceiling clearances

Consider a location where the fireplace screen will not be exposed to direct sunlight from

A 15 ampere 120 Volt 60 Hz branch circuit with proper ground must be available at the

location. Preferably a dedicated branch circuit should be provided to avoid circuit breakers

WM-50-XS

Description

Built-in Appliance

Voltage 120V AC 60Hz

Watts 1500W Max

NO HEATER 42W

MOTOR HEATER 19W

Appliance Width 50 1/4” or 127.56 cm

Appliance Height 15 3/8 ” or 39.1 cm

Appliance Depth 4 1/8” or 10.4 cm

Gross Weight 71.21 lbs or 32 kgs

Plug Location Left side

Cord Length 70 7/8” or 180 cm

Rough Wall Opening

Size

50 1/2”× 15 5/8“ or

128.27 cm× 39.688 cm

BTU 5118

This appliance has been tested in accordance

with the UL Standard 2021 for fixed and location

dedicated electric room appliances in the United

States and Canada. If you need assistance

during installation please contact your local

dealer.

NOTE: This applianc must b l ctrically

wir d and ground d in accordanc with local

cod s. In th abs nc of local cod s, us th

curr nt CSA C22.1 Canadian El ctrical Cod

in Canada or th ANSI/NFPA 70 National

El ctrical Cod in th Unit d Stat s.

161

2" [418.2mm]

521

8" [1324mm]

4" [273.5mm]

481

8" [1223mm]

8" [391mm]

8" [104mm]

8" [119mm]

501

4" [1275.6mm]

WM-60-XS

Description

Built-in Appliance

Voltage 120V AC 60Hz

Watts 1500W Max

NO HEATER 46W

MOTOR HEATER 19W

Appliance Width 60 1/4” or 152.96 cm

Appliance Height 15 3/8 ” or 39.1 cm

Appliance Depth 4 1/8” or 10.4 cm

Gross Weight 83.99 lbs or 38.1 kgs

Plug Location Left side

Cord Length 70 7/8” or 180 cm

Rough Wall Opening

Size

60 1/2”× 15 5/8“ or

153.67 cm× 39.688 cm

BTU 5118

This appliance has been tested in accordance

with the UL Standard 2021 for fixed and location

dedicated electric room appliances in the United

States and Canada. If you need assistance

during installation please contact your local

dealer.

NOTE: This applianc must b l ctrically

wir d and ground d in accordanc with local

cod s. In th abs nc of local cod s, us th

curr nt CSA C22.1 Canadian El ctrical Cod

in Canada or th ANSI/NFPA 70 National

El ctrical Cod in th Unit d Stat s.

161

2" [418.2mm]

621

8" [1578mm]

4" [273.5mm]

581

8" [1477mm]

8" [391mm]

8" [104mm]

8" [119mm]

601

4" [1529.6mm]

INSTALLATION-

WALL MOUNT

NOTE: Due to the many different materials used to build walls, it is highly recommended that you consult your

local builder before you install this appliance on a wall.

1. Select a location that is not prone to moisture and is located at least .91 m or 3 feet away from combustible

materials such as curtains or drapes, furniture, bedding, paper, etc.

2. Using a spirit level to select a position in which to mount the heater horizontally. See Figure 1.

3. Check the wall to ensure there is no wiring, pipe wires etc in the area to be drilled. Drill 8 or more holes

depending on the size of the unit purchased, (8mm diameter & 4 mm depth) using a suitable size drill bit and

insert the wall plugs into the holes.

4. Remove the hanger from the fireplace by removing the screws. See Figure 2.

5. Screw the left and right side steel panel to the left and right side to cover the screws. See Figure 3.

Min. 5cm

2 in

Min. 5cm

2 in

Min. 5cm

2 in

FLOOR

Fig 1 Fig 2 Fig 3

Fig 4

Fig 5

Fig 6

6. Fasten the hanger to the wall (See Figure 4.). Hang the fireplace onto the hanger (See Figure 5.).

7. To prevent fireplace from moving, use the provided safety screw to fasten the fireplace to the wall. See Figure 6.

WARNING: Be sure that the bolts have been fixed firmly enough to

withstand the weight!

INSTALLATION- BUILT-

NOTE: Due to the many different materials used to build walls it

you consult your local builder before you install this appliance on a wall.

Pr paration

Select a location that is not prone to moisture and is located at least 0.91m or 3 feet away

from combustible materials such as curtains d

Mark the desired location on the floor and store the appliance in a safe dry and dust free

place.

Prepare a wall with a framed opening to accommodate the size of your unit. Leave at

least 1/4” (6mm) around the edge o

compliance with local and national codes and other applicable regulations.

Prior to installing test the appliance to make sure the appliance is fully operational by

plugging the power supply cord into a 120

INSTALLATION

NOTE: Due to the many different materials used to b

uild walls it

is highly recommended that

you consult your local builder before you install t

his appliance on a wall.

Select a location that is not prone to moisture and is located at least 0.91m or 3 feet away

from combustible materials such as curtains d

rapes furniture bedding paper etc.

Mark the desired location on the floor and store the appliance in a safe dry and dust free

Prepare a wall with a framed opening to accommodate the size of your unit. Leave at

least 1/4” (6mm) around the edge o

f the appliance. Any new wiring must be done in

compliance with local and national codes and other applicable regulations.

Prior to installing test the appliance to make sure the appliance is fully operational by

plugging the power supply cord into a 120

Volt grounded outlet.

is highly recommended that

you consult your local builder before you install this appliance on a wall.

Select a location that is not prone to moisture and is located at least 0.91m or 3 feet away

rapes furniture bedding paper etc.

Mark the desired location on the floor and store the appliance in a safe dry and dust free

Prepare a wall with a framed opening to accommodate the size of your unit. Leave at

f the appliance. Any new wiring must be done in

compliance with local and national codes and other applicable regulations.

Prior to installing test the appliance to make sure the appliance is fully operational by

The rough wall opening size of the fireplace:

W(“)

WM-50-XS

WM-60-XS

The rough wall opening size of the fireplace:

D(“)

H(“)

4 3/8 15 5/8

50 1/2

4 3/8 15 5/8

60 1/2

Screw

1. Unscrew 1 screw on each left and right side and push the front glass panel upward a bit

to take it off. (The screws are only for protection during transportation.)

This manual suits for next models

Table of contents

Other Remii Indoor Fireplace manuals

Remii

Remii WM-SLIM-55 Installation instructions

Remii

Remii WM SLIM Series Assembly instructions

Remii

Remii Amantii CLASSIC SLIM 33 Assembly instructions

Remii

Remii WM-55-XS User manual

Remii

Remii 102755-XT Owner's manual

Remii

Remii WM-45-XS User manual

Remii

Remii 102745-DE User manual

Remii

Remii WM-34 User manual

Remii

Remii WM-55-XS Owner's manual

Remii

Remii CLASSIC SLIM-26 Owner's manual

Remii

Remii WM-34-B Owner's manual

Remii

Remii WM-SLIM-65 Owner's manual

Remii

Remii 30-BAY SLIM User manual

Remii

Remii 102745-XT Owner's manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual