RA rightangle 50591 User manual
7
. ATTACH THE COLUMN ASSEMBLIES
PAGE 1 OF 3
. DO NOT OVER-
STEP 4: AT 4" FROM THE BOTTOM OF THE
CORDLESS DRILL WITH
DETAIL A
. INSERT THESE THROUGH THE HOLES ON EACH END OF THE
. USE THE HEX HEAD DRIVER BIT OR THE
FULLY TIGHTEN.
STEP 6:
TIGHTEN THE SOCKET SCREWS
* 1 ON 60" OR 2" WORKSTATION
.
INSERT (2) END CAPS
LEVEL
1
WORKSURFACE SUPPORT AS SHOWN IN THE DETAIL BELOW LEFT AND FULLY
WRENCH
SPECIAL EXCEPTION: ON WORKSTATIONS ON
AND THREAD THEM INTO THE HOLES IN THE T-SLOT PLATES
ALLEN WRENCH PROVIDED
ALLOW FOR CLEARANCE OF THE EQUIPMENT.
5
8
#2 PHILLIPS HEAD DRIVER BIT OR
CROSS SUPPORT
AND
/32" HEX HEAD BIT OR ALLEN
STEP 5:
TO THE WORKSURFACE USING (16) WOOD SCREWS
*** ONLY ON 60" OR 2" WORKSTATIONS
5
** 1 ON 60" OR 2" WORKSTATION
2
32
3
PRE-INSTALLED IN THE COLUMN ASSEMBLIES
. INTO THE ENDS OF THE CROSS SUPPORT
TAPE MEASURE
VERSION DATED: 9/8/11
. SEE DETAIL A. DO NOT
WHICH THE LifeBalance STATION IS BEING INSTALLE , THE CROSS SUPPORT
DO NOT OPERATE THE UNIT UNTIL IT IS FULLY ASSEMBLED.
TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRILL.
14
LEVEL THE CROSS SUPPORT
TOOLS RE UIRED FOR ASSEMBLY:
4
4
ALIGN THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE PILOT
AND
4
INSTRUCTION # 50591
READ ALL OF THE INSTRUCTIONS BEFORE BEGINNING
#2 SQUARE HEAD DRIVER BIT
HOLES IN THE WORKSURFACE
SHOUL BE ATTACHE RESTING ON THE FEET OF THE COLUMN ASSEMBLIES TO
NewHeights ELECTRIC HEIGHT ADJUSTABLE WORKSTATION ASSEMBLY INSTRUCTIONS:
STEP 1: LAY THE WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE PILOT
HOLES FACING UP.
STEP 2: PLACE THE COLUMN ASSEMBLIES 2 AND 3 ON THE WORKSURFACE
WITH THE FEET FACING UP. THE MOTOR WIRES MUST FACE THE INSIDE OF THE
WORKSTATION.
STEP 3: WITH THE HELP OF AN ASSISTANT, PLACE (4) STAR WASHERS
6 ON (4)
SOCKET SCREWS
ITEM # PART # DESCRIPTION QTY.
1 VARIES WORKSURFACE 1
2 VARIES NewHeights COLUMN ASSY LEFT HAND 1
3 VARIES NewHeights COLUMN ASSY RIGHT HAND 1
4 VARIES NewHeights CROSS SUPPORT 1
5 524 0 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW 4
6 524 3/8 INTERIOR TOOTH STAR WASHER 4
800411 NewHeights/HOVER END CAP 2
8 51 08 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 19 OR 1 *
9 50285 NewHeights HAND SWITCH 1
10 500 2 8 x 3/4 PHILLIPS PAN HEAD RECEX DRIVE SCREW 4
11 51951 WIRE MANAGEMENT J 3 OR 1 **
12 VARIES 42" OR 54" U-CHANNEL 1 ***
13 52498 /32" ALLEN WRENCH 1
14 50298 NewHeights 2-LEGGED CONTROL BOX 1
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
.raproducts.com
K&A MANUFACTURING
FOOT
5
STEPS 1-6
1
MOTOR WIRES
SUPPORT
WORKSURFACE
8
BACK
3
4
6
2
A
LOCATING THE CROSS SUPPORT
4
(SEE EXCEPTION IN STEP 4)
BOTTOM OF
WORKSURFACE
SUPPORT
HARDWARE PACK # 52226
4.00
PRE-INSTALLED
T-SLOT PLATE
THE WORKSTATION. IF YOUR WORKSTATION HAS CASTERS, TURN THE BOLTS AT THE TOP OF THE CASTERS CLOCK-
LH COLUMN
PAGE 2 OF 3
WISE TO LEVEL THE WORKSTATION.
STEP 7: ALIGN THE HOLES IN THE HAND SWITCH 9 WITH THE PILOT HOLES AT THE BOTTOM FRONT EDGE OF THE
WORKSURFACE 1 . ATTACH THE SWITCH WITH (2) RECEX DRIVE SCREWS 10 .
STEP 8: ALIGN THE HOLES IN THE CONTROL BOX 14 WITH THE PILOT HOLES NEAR THE BACK CENTER OF THE
WORKSURFACE 1 . ATTACH THE CONTROL BOX WITH (2) RECEX DRIVE SCREWS 10 .
STEP 9: ATTACH (3) WIRE MANAGEMENT J'S 11 TO THE BOTTOM OF THE WORKSURFACE 1 WITH (3) WOOD
SCREWS 8 . (NO PILOT HOLES ARE PROVIDED.) ON 60" AND 2" WORKSTATIONS THE (2) WIRE MANAGEMENT J'S
NEAR THE CONTROL BOX 14 ARE REPLACED BY A METAL U-CHANNEL 12 .
STEP 10: RUN THE WIRES THROUGH THE WIRE MANAGEMENT J'S
11 AS SHOWN ON THE WIRE RUNS DIAGRAM
BELOW. WHEN THE WORKSTATION INCLUDES A U-CHANNEL, RUN THE WIRES THROUGH IT INSTEAD OF THE (2) WIRE
MANAGEMENT J'S. PLUG THE WIRES INTO THE CONTROL BOX 14 AS SHOWN ON THE WIRING DIAGRAM BELOW.
WITH THE HELP OF AN ASSISTANT, STAND THE WORKSTATION UPRIGHT IN ITS FINAL LOCATION. LEVEL THE WORK-
STATION IF REQUIRED BY TURNING THE LEVELING GLIDES CLOCKWISE (FROM THE TOP) ON THE LOW CORNERS OF
WIRING DIAGRAM
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
.raproducts.com
VERSION DATED: 9/8/11
K&A MANUFACTURING
10
LEVELING GLIDE
OR CASTER
11
14
SHOWN ON THESE VIEWS SO THE
NOTE: CROSS SUPPORT IS NOT
SWITCH
FRONT
1
STEPS 7-9
10
OTHER COMPONENTS ARE VISIBLE.
8
9
STEP 10
WIRE RUNS
60" & 2" WORKSTATIONS.
RH COLUMN RIGHT COLUMN WIRE
LEFT COLUMN WIRE
METAL U-CHANNEL 12
REPLACES THESE (2) WIRE
MANAGEMENT J'S ON
HAND SWITCH WIRE
A
M1 M2HS
END OF CONTROL BOX
SERIAL NUMBER
ON STICKER
BACK OF RIGHT HAND COLUMN ASSEMBLY
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
.raproducts.com
VERSION DATED: 9/8/11
K&A MANUFACTURING
HAND SWITCH
PAGE 3 OF 3
NewHeights ELECTRIC HEIGHT ADJUSTABLE WORKSTATION OPERATION INSTRUCTIONS:
CAUTION! TO PREVENT PINCHING OR COLLISION, MAKE SURE THAT YOU, YOUR FINGERS,
AN OTHER OBJECTS ARE AT LEAST 3/4" FROM THE TABLE'S E GES AN TRAVEL PATH.
STARTUP/RESET PROCEDURE:
STEP 1: PLUG THE POWER CORD FROM THE CONTROL BOX INTO A STANDARD 110 VOLT
RECEPTACLE.
STEP 2: TO SET THE WORKSTATION, PRESS AND HOLD THE DOWN BUTTON ON THE HAND
SWITCH UNTIL THE WORKSTATION STOPS AT ITS LOWEST POSITION. THE NewHeights WORK-
STATION IS NOW READY FOR USE.
IF YOU ARE HAVING ANY PROBLEMS WITH THE PREVIOUS STEPS, CONTACT RIGHTANGLE
SERVICE AT THE NUMBER ABOVE LEFT OR info@raproducts.com.
TROUBLESHOOTING:
IF THE WORKSTATION STOPS OPERATING OR A POWER FAILURE OCCURS, UNPLUG THE
POWER CORD FROM THE RECEPTACLE AND REPEAT STEP 1 AND STEP 2 ABOVE.
WARRANTY INFORMATION:
NewHeights PRODUCTS ARE WARRANTED TO BE FREE OF DEFECTS DUE TO
MANUFACTURING OR MATERIALS AS FOLLOWS: 2 YEARS ON THE GEAR AND/OR MOTOR,
INCLUDING THE CONTROL BOX AND HAND SWITCH. 5 YEARS ON THE SUPPORT BRACKETS,
ALUMINUM COLUMNS AND FEET. WE WILL REPLACE ANY DEFECTIVE PART AFTER
INSPECTION BY AN AUTHORIZED AGENT. COSTS INCURRED DUE TO PRODUCT
REPLACEMENT SUCH AS INSTALLATION, LABOR CHARGES OR TRANSPORTATION ARE NOT
COVERED UNDER THIS WARRANTY. WHEN CORRESPONDING WITH RIGHTANGLE
PRODUCTS, RECORD AND PROVIDE THE SERIAL NUMBER LOCATED ON THE BACK
PORTION OF THE RIGHT HAND COLUMN ASSEMBLY. SEE THE DETAIL BELOW.
SPECIAL NOTE: DO NOT USE ANY ABRASIVE CLEANERS ON THIS UNIT.
Other RA Indoor Furnishing manuals
