Mitsubishi Electric City Multi PCFY-P40VKM-E Operating manual

TECHNICAL & SERVICE MANUAL

CONTENTS

1. TECHNICAL CHANGES ......................... 2

2. SAFETY PRECAUTION .......................... 2

3. PART NAMES AND FUNCTIONS .......... 4

4. SPECIFICATION ................................... 11

5. OUTLINES AND DIMENSIONS ............ 15

6. WIRING DIAGRAM ............................... 18

7. REFRIGERANT SYSTEM DIAGRAM ........ 20

8. TROUBLESHOOTING .......................... 21

9. DISASSEMBLY PROCEDURE ............. 30

Indoor unit

[Model names] [Service Ref.]

No. OCH449

REVISED EDITION-A

INDOOR UNIT

SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS

R410A

Note:

•

This manual describes only

service data of the indoor units.

• RoHS compliant products have

<G> mark on the spec name

plate.

December 2012

PARTS CATALOG (OCB449)

Model name

indication

PCFY-P40VKM-E

PCFY-P63VKM-E

PCFY-P100VKM-E

PCFY-P125VKM-E

PCFY-P40VKM-E

PCFY-P40VKM-ER1

PCFY-P63VKM-E

PCFY-P63VKM-ER1

PCFY-P100VKM-E

PCFY-P100VKM-ER1

PCFY-P125VKM-E

PCFY-P125VKM-ER1

Revision:

•

PCFY-P40/63/100/125VKM-ER1

have been added in REVISED

EDITION-A.

• Some descriptions have been

modified.

• Please void OCH449.

2SAFETY PRECAUTION

1TECHNICAL CHANGES

PCFY-P40VKM-E PCFY-P40VKM-ER1

PCFY-P63VKM-E PCFY-P63VKM-ER1

PCFY-P100VKM-E PCFY-P100VKM-ER1

PCFY-P125VKM-E PCFY-P125VKM-ER1

• INDOOR CONTROLLER BOARD (I.B.) has been changed. (S/W version up)

Cautions for units utilizing refrigerant R410A

Charge refrigerant from liquid phase of gas

cylinder.

If the refrigerant is charged from gas phase, composition

change may occur in refrigerant and the efficiency will be

lowered.

Do not use refrigerant other than R410A.

If other refrigerant (R22 etc.) is used, chlorine in refrige-

rant can cause deterioration of refrigerant oil etc.

Use a vacuum pump with a reverse flow check

valve.

Vacuum pump oil may flow back into refrigerant cycle and

that can cause deterioration of refrigerant oil etc.

Use the following tools specifically designed for

use with R410A refrigerant.

The following tools are necessary to use R410A refrigerant.

Handle tools with care.

If dirt, dust or moisture enters into refrigerant cycle, that can

cause deterioration of refrigerant oil or malfunction of com-

pressor.

Do not use a charging cylinder.

If a charging cylinder is used, the composition of refrigera-

nt will change and the efficiency will be lowered.

Flare tool

Electronic refrigerant

charging scale

Vacuum pump adaptor

Size adjustment gauge

Gauge manifold

Torque wrench

Gas leak detector

Charge hose

Tools for R410A

If dirt, dust or moisture enters into refrigerant cycle, that can

cause deterioration of refrigerant oil or malfunction of com-

pressor.

If large amount of mineral oil enters, that can cause deterio-

ration of refrigerant oil etc.

Do not use the existing refrigerant piping.

The old refrigerant and lubricant in the existing piping

contains a large amount of chlorine which may cause the

lubricant deterioration of the new unit.

Use “low residual oil piping”

If there is a large amount of residual oil (hydraulic oil, etc.)

inside the piping and joints, deterioration of the lubricant

will result.

Never use any refrigerant other than that specified.

Doing so may cause a burst, an explosion, or fire when the

unit is being used, serviced, or disposed of.

Correct refrigerant is specified in the manuals and on the

spec labels provided with our products.

We will not be held responsible for mechanical failure,

system malfunction, unit breakdown or accidents caused

by failure to follow the instructions.

Use the specified refrigerant only.

Store the piping indoors, and both ends of the

piping sealed until just before brazing.

(Leave elbow joints, etc. in their packaging.)

The refrigerant oil applied to flare and flange

connections must be ester oil, ether oil or

alkylbenzene oil in a small amount.

Ventilate the room if refrigerant leaks during

operation. If refrigerant comes into contact with

a flame, poisonous gases will be released.

OCH449A

Gravimeter

Unit

[3] Service tools

Use the below service tools as exclusive tools for R410A refrigerant.

[1] Cautions for service

(1) Perform service after recovering the refrigerant left in unit completely.

(2) Do not release refrigerant in the air.

(3) After completing service, charge the cycle with specified amount of refrigerant.

(4) When performing service, install a filter drier simultaneously.

Be sure to use a filter drier for new refrigerant.

[2] Additional refrigerant charge

When charging directly from cylinder

· Check that cylinder for R410A on the market is syphon type.

· Charging should be performed with the cylinder of syphon standing vertically. (Refrigerant is charged from liquid phase.)

No. Tool name Specifications

1Gauge manifold

· Only for R410A

· Use the existing fitting specifications. (UNF1/2)

· Use high-tension side pressure of 5.3MPa·G or over.

2Charge hose · Only for R410A

· Use pressure performance of 5.09MPa·G or over.

3Electronic scale

4Gas leak detector · Use the detector for R134a, R407C or R410A.

5Adaptor for reverse flow check · Attach on vacuum pump.

6Refrigerant charge base

7Refrigerant cylinder · Only for R410A · Top of cylinder (Pink)

· Cylinder with syphon

8Refrigerant recovery equipment

OCH449A

3-1. INDOOR UNIT

3PART NAMES AND FUNCTIONS

Air outlet

Louver

Vane

Air intake Filter

(Inside of Air intake)

OCH449A

Function buttons

F1 F2 F3 F4

Press to turn ON/OFF the indoor unit.

ON / OFF button

When the backlight is off, pressing any button turns

the backlight on and does not perform its function.

(except for the (ON / OFF) button)

The functions of the function buttons change depending on

the screen. Refer to the button function guide that appears

at the bottom of the LCD for the functions they serve on a

given screen.

When the system is centrally controlled, the button function

guide that corresponds to the locked button will not appear.

Press to save the setting.

SELECT button

Press to return to the previous screen.

RETURN button

Press to bring up the Main menu.

MENU button

Operation settings will appear.

When the backlight is off, pressing any button turns the

backlight on and it will stay lit for a certain period of time

depending on the screen.

Backlit LCD

This lamp lights up in green while the unit is in operation.

It blinks while the remote controller is starting up or when

there is an error.

ON / OFF lamp

Main display : Press to change the operation mode.

Main menu : Press to move the cursor down.

Function button F1

Main display : Press to decrease temperature.

Main menu : Press to move the cursor up.

Function button F2

Main display : Press to increase temperature.

Main menu : Press to go to the previous page.

Function button F3

Main display : Press to change the fan speed.

Main menu : Press to go to the next page.

Function button F4

Fri

Room

Set temp.

Mode Temp. Fan

Cool Auto

Main

Main display:

Cursor Page

Main menu

Vane·Louver·Vent. (Lossnay)

High power

Timer

Weekly timer

OU silent mode

Function guide

3-2. WIRED REMOTE CONTROLLER <PAR-30MAA/PAR-31MAA>

* The functions which can be used are restricted according to the model.

: Supported : Unsupported

Function PAR-30MAA/PAR-31MAA PAR-21MAA

Slim City multi

Body Product size H × W × D (mm) 120 × 120 × 19 120 × 130 × 19

LCD Full Dot LCD Partial Dot LCD

Backlight

Energy-saving Energy-saving operation schedule

Automatic return to the preset temperature

Restriction Setting the temperature range restriction

Function Operation lock function

Weekly timer

On / Off timer

High Power

Manual vane angle

Wired remote controller function

OCH449A

Fri

Mode Temp. Fan

Room

Cool Auto

Set temp.

Fri

Cool

Mode Temp. Fan

AutoSet temp.

The main display can be displayed in two different modes: "Full" and "Basic".

he factory setting is "Full". To switch to the "Basic" mode, change the setting on the Main display setting.

* All icons are displayed for explanation.

Most settings (except ON / OFF, mode, fan speed, temperature) can be made from the Menu screen.

Indoor unit operation mode appears here.

Operation mode

Preset temperature appears here.

Preset temperature

Current time appears here.

Clock (See the Installation Manual.)

Fan speed

Fan speed setting appears here.

Functions of the corresponding buttons appear here.

Button function guide

Appears when the ON/OFF operation is centrally controlled.

Appears when the operation mode is centrally controlled.

Appears when the preset temperature is centrally controlled.

Appears when the f lter reset function is centrally controlled.

Indicates when f lter needs maintenance.

Current room temperature appears here.

Room temperature

(See the Installation Manual.)

Appears when the buttons are locked.

Appears when the On/Off timer or Night setback function is

enabled.

Appears when the Weekly timer is enabled.

Appears while the units are operated in the energy-save

mode.

Appears when the built-in thermistor on the remote control-

ler is activated to monitor the room temperature.

appears when the thermistor on the indoor unit is acti-

vated to monitor the room temperature.

Indicates the vane setting.

Indicates the louver setting.

Indicates the ventilation setting.

Appears when the preset temperature range is restricted.

OCH449A

Not all functions are available on all models of indoor units.

Filter information

Error information

Energy saving

Auto return

Schedule

Night setback

Main menu Press the MENU button.

Move the cursor to the desired item with the F1 and F2 buttons, and press the SELECT button.

Vane · Louver · Vent. (Lossnay)

High power

Weekly timer

Restriction

Maintenance

Initial setting

On / Off timer

Auto-Off timer

Temp. range

Operation lock

Manual vane angle

Main / Sub

Timer

Main display

Contrast

Display details

Auto mode

Administrator password

Language selection

Service

Service menu

Input maintenance info.

Function setting

Lossnay (City Multi only)

Check

Self check

Maintenance password

Remote controller check

Test run

Clock

Drain pump test run

Auto descending panel

Menu structure

OCH449A

Setting and display items Setting details

Vane · Louver · Vent.

(Lossnay)

Use to set the vane angle.

• Select a desired vane setting from f ve different settings.

Use to turn ON / OFF the louver.

• Select a desired setting from "ON" and "OFF."

Use to set the amount of ventilation.

• Select a desired setting from "Off," "Low," and "High."

High power Use to reach the comfortable room temperature quickly.

• Units can be operated in the High-power mode for up to 30 minutes.

Timer On/Off timer Use to set the operation On/Off times.

• Time can be set in 5-minute increments.

* Clock setting is required.

Auto-Off

timer

Use to set the Auto-Off time.

• Time can be set to a value from 30 to 240 in 10-minute increments.

Filter information Use to check the f lter status.

• The f lter sign can be reset.

Error information Use to check error information when an error occurs.

• Error code, error source, refrigerant address, unit model, manufacturing number, contact

information (dealer's phone number) can be displayed.

* The unit model, manufacturing number, and contact information need to be registered in

advance to be displayed.

Weekly timer Use to set the weekly operation On / Off times.

• Up to eight operation patterns can be set for each day.

* Clock setting is required.

* Not valid when the On/Off timer is enabled.

Energy

saving

Auto return Use to get the units to operate at the preset temperature after performing energy-save

operation for a specif ed time period.

• Time can be set to a value from 30 and 120 in 10-minute increments.

* This function will not be valid when the preset temperature ranges are restricted.

Schedule Set the start/stop times to operate the units in the energy-save mode for each day of the

week, and set the energy-saving rate.

• Up to four energy-save operation patterns can be set for each day.

• Time can be set in 5-minute increments.

• Energy-saving rate can be set to a value from 0% or 50 to 90% in 10% increments.

* Clock setting is required.

Night setback Use to make Night setback settings.

• Select "Yes" to enable the setting, and "No" to disable the setting. The temperature range and

the start/stop times can be set.

* Clock setting is required.

Restriction Temp. range Use to restrict the preset temperature range.

• Different temperature ranges can be set for different operation modes.

Operation

lock

Use to lock selected functions.

• The locked functions cannot be operated.

Maintenance Auto

descending

panel

Auto descending panel (Optional parts) Up / Down you can do.

Manual

vane angle

Use to set the vane angle for each vane to a f xed position.

Initial setting Main/Sub When connecting two remote controllers, one of them needs to be designated as a sub

controller.

Clock Use to set the current time.

Main display Use to switch between "Full" and "Basic" modes for the Main display.

• The default setting is "Full."

Contrast Use to adjust screen contrast.

Main menu list

OCH449A

Setting and display items Setting details

Initial setting Display

details

Make the settings for the remote controller related items as necessary.

Clock: The factory settings are "Yes" and "24h" format.

Temperature: Set either Celsius (°C) or Fahrenheit (°F).

Room temp. : Set Show or Hide.

Auto mode: Set the Auto mode display or Only Auto display.

Auto mode Whether or not to use the AUTO mode can be selected by using the button.

This setting is valid only when indoor units with the AUTO mode function are connected.

Administrator

password

The administrator password is required to make the settings for the following items.

• Timer setting • Energy-save setting • Weekly timer setting

• Restriction setting • Outdoor unit silent mode setting • Night set back

Language

selection

Use to select the desired language.

Service Test run Select "Test run" from the Service menu to bring up the Test run menu.

• Test run • Drain pump test run

Input

maintenance

Select "Input maintenance Info." from the Service menu to bring up the Maintenance

information screen.

The following settings can be made from the Maintenance Information screen.

• Model name input • Serial No. input • Dealer information input

Function

setting

Make the settings for the indoor unit functions via the remote controller as necessary.

LOSSNAY

setting

(City Multi only)

This setting is required only when the operation of City Multi units is interlocked with

LOSSNAY units.

Check Error history: Display the error history and execute delete error history.

Refrigerant leak check: Refrigerant leaks can be judged.

Smooth maintenance: The indoor and outdoor maintenance data can be displayed.

Request cord: Details of the operation data including each thermistor temperature and error

history can be checked.

Self check Error history of each unit can be checked via the remote controller.

Maintenance

password

Take the following steps to change the maintenance password.

Remote

controller

check

When the remote controller does not work properly, use the remote controller checking

function to troublushoot the problem.

OCH449A

°F°C

ERROR CODE

AFTER

TIMER

TIME SUN MON TUE WED THU FRI SAT

OFF

AFTER

FILTER

FUNCTION

ONLY1Hr.

WEEKLY

SIMPLE

AUTO OFF

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

●

Display Section

For purposes of this explanation,

all parts of the display are shown.

During actual operation, only the

relevant items will be lit.

Identifies the current operation

Shows the operating mode, etc.

*Multilanguage display is available.

“Centrally Controlled” indicator

Indicates that operation from the

remote controller has been prohib-

ited by a master controller.

“Timer is Off” indicator

Indicates that the timer is off.

Temperature Setting

Shows the target temperature.

Day-of-Week

Shows the current day of the week.

Time/Timer Display

Shows the current time, unless the simple or Auto Off

timer is set.

If the simple or Auto Off timer is set, the time to be

switched off is shown.

“Sensor” indication

Displayed when the remote controller

sensor is used.

“Locked” indicator

Indicates that remote controller but-

tons have been locked.

“Clean The Filter” indicator

To be displayed on when it is time to

clean the filter.

Timer indicators

The indicator comes on if the corre-

sponding timer is set.

Up/Down Air Direction indica-

tor

The indicator shows the direc-

tion of the outcoming airflow.

“One Hour Only” indicator

Room Temperature display

Shows the room temperature. The room

temperature display range is 8 - 39°C.

The display blinks if the temperature

is less than 8°C or 39°C or more.

Louver display

Indicates the action of the swing louver.

Does not appear if the louver is not

running.

(Power On indicator)

Indicates that the power is on.

Fan Speed indicator

Shows the selected fan speed.

Ventilation indicator

Appears when the unit is running in

Ventilation mode.

Operation Section

Temperature setting buttons

Down

Timer Menu button

(Monitor/Set button)

Mode button (Return button)

Set Time buttons

Back

Ahead

Timer On/Off button

(Set Day button)

Opening the

cover

ON/OFF button

Fan Speed button

Filter button

(<Enter> button)

Test Run button

Check button (Clear button)

Airflow Up/Down button

Louver button

( Operation button)

To return operation

number

Ventilation button

( Operation button)

To go to next operation

number

Note:

“PLEASE WAIT” message

This message is displayed for approximately 3 minutes when power is supplied to the indoor unit or when the unit is recovering from a power failure.

“NOT AVAILABLE” message

This message is displayed if an invalid button is pressed (to operate a function that the indoor unit does not have).

If a single remote controller is used to operate multiple indoor units simultaneously that are different types, this message will not be displayed as

far as any of the indoor units is equipped with the function.

Built-in temperature sensor

Displayed if the airflow is set to

Low or downward during COOL

or DRY mode. (Operation varies

according to model.)

The indicator goes off in one hour,

at which time the airflow direction

also changes.

3-3. WIRED REMOTE CONTROLLER <PAR-21MAA>

OCH449A

Other manuals for City Multi PCFY-P40VKM-E

This manual suits for next models

Table of contents

Other Mitsubishi Electric Air Conditioner manuals

Mitsubishi Electric

Mitsubishi Electric MSZ-EF18VEW User manual

Mitsubishi Electric

Mitsubishi Electric MS-09SN-C1 User manual

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PEA-A12AA4 Operating manual

Mitsubishi Electric

Mitsubishi Electric PKFY-P NBMU-E User manual

Mitsubishi Electric

Mitsubishi Electric MXZ-6C122VA User manual

Mitsubishi Electric

Mitsubishi Electric MFZ-KT25VG-E1 User manual

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PEFY Series User manual

Mitsubishi Electric

Mitsubishi Electric Mr. Slim SUZ-KA12NAHZ User manual

Mitsubishi Electric

Mitsubishi Electric MUFZ-KJ25VEHZ User manual

Mitsubishi Electric

Mitsubishi Electric MS-07NV -E1 (WH) User manual

Mitsubishi Electric

Mitsubishi Electric Mr. Slim PKA-RP60KAL User manual

Mitsubishi Electric

Mitsubishi Electric MXZ-5E102VA User manual

Mitsubishi Electric

Mitsubishi Electric CITY MULTI CMH-WM-V-A Series Product guide

Mitsubishi Electric

Mitsubishi Electric CMB-WM108V-AA User manual

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PUHZ-FRP71VHA User manual

Mitsubishi Electric

Mitsubishi Electric MSZ-AP25VG-E1 User manual

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PLFY-EP.NEMU-E Series User manual

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PKFY-P-VKM-E User manual

Mitsubishi Electric

Mitsubishi Electric Mr. SLIM PCA-A GA Series User manual

Mitsubishi Electric

Mitsubishi Electric City Multi PMFY-P20VBM-E User manual

Mitsubishi Electric

Mitsubishi Electric MSC-GA20VB- E1 User manual

Mitsubishi Electric

Mitsubishi Electric PLA Series User manual

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PUZ-ZM YKA Series User manual

Mitsubishi Electric

Mitsubishi Electric Mr. Slim PSA-RP100KA/PUHZ-P100YKA User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual