Mercia Garden Products 01OVLPA0507DDFW-V1 Instruction manual

N/A

Overlap

Cladding

Shiplap

Cladding

Solid Sheet

Roof

T&G Roof

Solid Sheet

Floor

T&G Floor

Fixed

Windows

Opening

Windows

For Assistance Please

Contact Customer Care on

01636 880514

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be erected by two

adults

For ease of assembly, it is advisable to

pilot drill all screw holes and ensure

all screw heads are countersunk.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand

(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,

step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather

conditions. For the duration of heavy or extended periods of rain, swelling of the

wood panels may occur. Warping of the wood may also occur during excessive

dry spells due to an interior moisture loss. Unfortunately, these processes cannot

be avoided but can be helped. It is suggested that the outdoor building is

sprayed with water during extended periods of warm sunshine and sheltered as

much as possible during rain or snow.

Our buildings are pre treated with a water based treatment**; this only helps to

protect the product during transit and for upto 3 months against mould. To

validate your guarantee and ensure longevity of the product, it is ESSENTIAL the

building is treated with a wood preserver within the rst three months of

assembly and thereafter in accordance with the manufactures recommenda-

tions. Care must be taken to ensure the product is placed on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Whilst all products manufactured are made to the

highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot

accept responsibility for your safety whilst erecting or

using this product.

Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces

of the timber. You are strongly advised

to wear gloves when working with or

handling rough sawn timer.

**Protim Fentex E5**

Biocidal Product Regulation (EU 528/2012) Article 58 Information

Protim Fentex E2 preserved wood is a “treated article”which incorporates biocidal products.

Wood correctly preserved with Protim Fentex E2 is protected against mould in storage.

Contains: IPBC (3-iodo-2-propynyl-N-butyl carbamate) and propiconazole.

Wear gloves when handling freshly treated wood.

Avoid breathing dust when cutting treated or untreated wood.

Dispose of o-cuts responsibly – do not burn.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer

to diagrams for the base dimensions, The base should be slightly smaller than

the external measurement of the building, i.e. The cladding should overlap the

base, creating a run o for water. It is also recommended that the oor be at

least 25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Please retain product label and instructions for future reference

P 1

General Instructions

01OVLPA0507DDFW-V1

5x7 Overlap apex shed with double doors, fixed windows, solid sheet floor and roof.

01OVLPA0507DDFW-V1-NW

5x7 Overlap apex shed with double doors, no windows, solid sheet floor and roof.

01OSBA0507DDFW-V1

5x7 Shiplap apex shed with double doors, fixed windows, solid sheet floor and roof.

01OSBA0507DDFW-V1-NW

5x7 Shiplap apex shed with double doors, no windows, solid sheet floor and roof.

01SHPA0507DDOW-V1

5x6 Shiplap apex shed with double doors, opening windows,T&G floor and roof.

01SHPA0507DDOW-V1-NW

5x7 Shiplap apex shed with double doors, no windows,T&G floor and roof.

Refer to the instructions pages for you specic product code

P 2

01OSBA0507DDFW-V1 & 01OSBA0507DDNW-V1

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

01OSBA0507DDFW-V1

01OSBA0507DDFW-V1-NW

Overall Dimensions:

Length = 1514cm

Width = 2106cm

Height = 2061cm

Base Dimensions:

Length = 2066cm

Width = 1456cm

Building content

Door Gable Back Gable Plain Side

- NW ONLY

Window Panel

- FW ONLY

123 4 567

Fascia 1186mm x4

Fixed Window Strip 546mm x3 - FW ONLY

Cover Trims 1575mm x4

Door Strip 1024mm

Ridge Bar 1434mm

Door Strip 530mm

Door Block 140mm x2

Finial x2

Roof

Floor Door

Door Beading Strip 1590mm x2 T Hinge

Qty 4

Plastic Window Cill

- FW ONLY

Felt

Styrene

Qty 1

- FW ONLY

L-Bracket

Qty 2

Turn Button

Qty 3

18 19

Eaves Frame 1517mm x2

Nail Bag

Felt Tacks x 80

20mm Screw x 13

30mm Black Screw x 3

30mm Screw x 73

40mm Screw x 44

50mm Screw x 28

Remove transportation

blocks from the bottom

of each panel before

beginning assembly. Each

Panel should have two

Pre Assembly

30mm

screw Pre drill

hole

Fix the T Hinges onto the

doors and door frame as

shown. Ensure that the

screws go through the

cladding and into the

framing behind.

28x30mm screws

P 3

Step 1

Place floor on firm and level base, ensure

base has suitable drainage free from areas

where water can collect. (See front page on

base requirements).

Do not secure the building to the

floor until the roof is fitted. Fix the

panels onto the floor using 50mm

screws in alignment with the floor

joists

Fix the corners with 50mm screws

as shown in diagram.

Position the panels so there is equal spacing

between the floor and cladding on all 4 sides

Step 2

3x50mm Screws

Pre drill

hole

50mm

screw

Step 3

9x50mm Screws

Fix the corners with 50mm

screws as shown in diagram.

Pre drill

hole

50mm

screw

Use part 3 for a no window

building and part 4 for a

windowed building

4 or 3

Step 4

8x20mm Screws

Place the ridge bar in between the front

and back gables. Ensure the top corners

of the ridge bar sit flush with the top

points of the door gable. Fix the ridge bar

to the gable using one L bracket for each

end.

Fix with 4x20mm screws each

20mm

screw Pre drill

hole

P 4

Step 5

Fix an eaves frame to each roof sheet

using 3x30mm screws per eave.

Fix the roof sheets to the roof ensuring

they come together at the top using

40mm screws directly through the roof

sheet at the top. Make sure to attach the

roofs to the ridge bar.

6x 30mm Screws

28x 40mm Screws

40mm

screw

Pre drill

hole

Pre drill

hole 30mm

screw

Step 6

bOnce the roof is fixed

attach the building to

the floor with 50 mm

screws.

16x 50mm Screws

50mm

screw Pre drill

hole

64x Tacks

Felt

tacks

HANDLE

WITH CARE

Step 7

Cut the felt into 1617mm long

sheets and lay onto roof as

shown in diagram ensuring

there is overhang around the

sides then nail the felt tacks

every 100mm.

Lay the capping felt over the

centre of the apex as shown

in the diagram ensuring there

is overhang around the sides.

P 5

Fit the Cover Trims to the front

and back of the building as

shown in the illustration using

30mm screws.Trim the length

of the cover trims to the

required size before fitting if

necessary.

Pre drill to avoid splitting.

12x30mm Screws

Step 8

30mm

screw Pre drill

hole

Step 9

16x40mm Screws

Attach the faiscas to the roof

leaving a slight overhang at the

top.

Fit the fascias to the roof over

the felt and secure in place with

40mm screws as shown.

Pre drill to avoid splitting.

40mm

screw Pre drill

hole

Step 10

Side View Place the

plastic window

cill onto the

Window Panel

in the same

way as shown

on both

diagrams to the

left.

Fit the styrene sheets on top of

the window cill.

When positioning the styrene

sheets ensure there is an equal

distance between them and at

either side of the windows.

Fix the window strips to the two

pieces of framing that sit

alongside the outside edges of

the window with 3x30mm

screws for each strip.

Attach the three window strips

at either side of the windows

using 3x30mm screws each.

Make sure the screws enter the

framing in the window panel

and not the styrene.

9x30mm Screws

For the no window version go to step 11

30mm

screw Pre drill

hole

6x30mm Screws

30mm

screw Pre drill

hole

P 6

Step 11

Use 4x30mm Screws to fix

each beading strip onto the

door gable. Ensure that the

screw is parallel with the

door frame when fixing the

strip to the door gable as

shown in the close up view.

Attach the turn button to

the top and bottom door

blocks with 1x30mm screw

for each one.

First line up the door blocks

at the top and bottom of the

doors.Then fix with

2x30mm screws by screwing

through the outside of the

door into the block.

8x30mm Screws

2x30mm Black Screws

4x30mm Screws

b ca

30mm

screw

30mm

screw

30mm

screw

Step 12

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Use 5x20mm screw to fix the

door strips to the master

door (Right door panel)

Note - Door Strips must be

attached to master door!

Use 1x30mm black screw to

fix the turn button onto the

slave door (left door panel)

5x20mm Screws

1x 30mm Black Screw

20mm

screw

Pre drill

hole

Pre drill

hole

30mm

screw

This manual suits for next models

Table of contents

Other Mercia Garden Products Outdoor Furnishing manuals

Mercia Garden Products

Mercia Garden Products 0628LOG171-V4 Instruction manual

Mercia Garden Products

Mercia Garden Products 01LOGHF-V1 User manual

Mercia Garden Products

Mercia Garden Products 0619LOG016-V4 Instruction manual

Mercia Garden Products

Mercia Garden Products 01OAOSB0705-V2 User manual

Mercia Garden Products

Mercia Garden Products 01GRO0606-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 01OSBA0304SDNW-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products Helios 03HEL1010DDFW-V3 Instruction manual

Mercia Garden Products

Mercia Garden Products 03TGCORSE0407-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 03TGCOR0909DDFW-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 01OSBP0604DFW-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 01OSBA0305SDNW-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 01OVLPRA0604SDFW-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 03PTMBPN0406BR-V1 User manual

Mercia Garden Products

Mercia Garden Products 0619LOG002-V4 Instruction manual

Mercia Garden Products

Mercia Garden Products Clover 03CLOV0808-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 01LOGST-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 0619LOG006-V4 Instruction manual

Mercia Garden Products

Mercia Garden Products 03BRN0705-V3 Instruction manual

Mercia Garden Products

Mercia Garden Products 01VINLOG0303-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 0628LOG125-V4 Instruction manual

Mercia Garden Products

Mercia Garden Products 01OVLPA1006DDFW-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 01VINLOG0307-V1 Instruction manual

Mercia Garden Products

Mercia Garden Products 0619LOG003-V4 Instruction manual

Mercia Garden Products

Mercia Garden Products 0628LOG131-V3 Instruction manual

Popular Outdoor Furnishing manuals by other brands

Belleze

Belleze 014-HG-20074 manual

Hatteras Hammocks

Hatteras Hammocks DCA1-K-HH instructions

Kozyard

Kozyard Morgan Aluminum Pergola Assembly manual

Lemeks

Lemeks Palmako PA120-5959 Assembly, installation and maintenance manual

Polywood

Polywood 400 Series Assembly instructions

OLT

OLT 24 Assembly manual

forest-style

forest-style HACIENDA 2354 Building instructions

Courtyard Creations

Courtyard Creations RUS0188-WM Assembly instructions

RPR

RPR OLLIE CHAIR manual

kingsley-bate

kingsley-bate MC-55 Assembly instructions

Weltevree

Weltevree Carrier product manual

Grange Fencing

Grange Fencing Elite Arch Assembly instructions

Grosfillex

Grosfillex AUVENT YR14 Assembly instructions

X-METAL

X-METAL EAGLE 33511 Assembly instructions

Anova

Anova FBW6R Assembly instructions

Outsunny

Outsunny 84A-090 manual

Ivy Terrace

Ivy Terrace IVTD212 Assembly instructions

Breezesta

Breezesta FANBACK ADIRONDACK AD-0101 Assembly