Kohler K-19480 User manual
Installation Guide
Single-Control Lavatory Faucet
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-19480
1050798-2-A
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Tools and Materials
Before You Begin
Observe all local plumbing and building codes.
Shut off the main water supply.
Carefully inspect the waste and supply tubing for any sign of
damage.
This faucet is for use on a single-hole lavatory.
For new installations, install the faucet and drain to the lavatory
before installing the lavatory.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
Thermometer
Strap
Wrench Thread
Sealant
Plumbers
Putty Hex
Wrench
Assorted
Screwdrivers
1050798-2-A 2 Kohler Co.
1. Install the Faucet
Thread the mounting studs into the holes in the bottom of the
faucet body.
NOTE: The base of the faucet may be attached to the lavatory using
either the supplied rubber washer or plumbers putty to form a
watertight seal. Do not attach the faucet to the lavatory using both
the rubber washer and plumbers putty.
For rubber washer attachment: Slide the washer over the supply
inlets and up to the faucet base.
For plumbers putty attachment: Apply the plumbers putty or
other sealant to the underside of the flange of the faucet base
according to the putty manufacturer’s instructions.
Feed the faucet supply inlets through the faucet hole of the
lavatory, then position the faucet.
Slide the washer and bracket over the mounting studs, then
securely tighten the nuts to the mounting studs.
Nut Bracket
Washer
Lavatory
Mounting Stud
Supply Inlet
Apply
plumbers
putty.
Rubber
Washer
Kohler Co. 3 1050798-2-A
2. Install the Drain
Remove the protective cover from the flange.
Apply a ring of plumbers putty or other sealant to the underside
of the flange according to the putty manufacturer’s instructions.
Assemble the nut, flat washer, and tapered gasket (tapered side
up) fully onto the body.
From the underside of the fixture, insert the drain body up into
the drain hole.
From the top of the fixture, securely hand tighten the flange onto
the drain body.
Make sure the drain body seal hole is facing the back of the
fixture, and securely tighten the nut.
Remove any excess putty or sealant.
Apply plumbers putty.
Flange
Tapered Gasket
Flat Washer
Nut
Drain Body
Fixture
1050798-2-A 4 Kohler Co.
3. Complete the Drain Installation
Press the seal into the seal hole on the body.
Insert the stopper into the flange.
For regular installations, insert the short end of the rod into the
body seal hole and under the stopper rod. For vandal-resistant
installations, fit the rod through the hole in the stopper rod.
Hand tighten the rod nut.
Remove and adjust the stopper as needed so it lifts about 3/8″(1
cm) when opened. To adjust, rotate the threaded stopper rod in or
out as needed. Retighten the stopper nut.
Apply thread sealant tape to the tailpiece threads, then thread the
tailpiece to the body. Tighten the tailpiece securely.
Slide one end of the clip onto the rod. Slide the link onto the lift
rod with the thumbscrew facing the back of the fixture.
Squeeze the other end of the clip, aligning the hole with the rod.
Move the link to the proper position by squeezing the clip and
sliding it along the rod.
Insert the lift rod into the hole in the body and then into the hole
in the link.
Tighten the thumbscrew onto the link so the lift rod knob extends
1/2″(1.3 cm) above the lift rod hole.
Body
Clip
Stopper
Stopper Nut
Flange
Seal
Rod Nut
Tailpiece
Apply
thread
sealant.
Thumb
Screw
Stopper
Rod
Link
Rod
Lift
Rod
Kohler Co. 5 1050798-2-A
4. Connect the Supplies
If the lavatory is not installed, install it at this time. Follow the
lavatory manufacturer’s instructions.
NOTE: Connect the supply hose marked with a blue dot to the cold
supply.
Connect the supply hoses to the supply stops. (Left is hot - right
is cold.)
Supply
Stop
Supply
Hose
1050798-2-A 6 Kohler Co.
5. Installation Checkout
Connect the drain tailpiece into the P-trap.
Ensure that all connections are tight.
Using the tool provided, remove the aerator.
Turn on the main water supply and check for leaks. Repair as
needed.
Lift and rotate the faucet handle to the full hot position, then the
full cold position. Run water through the spout for about one
minute to remove any debris. Check for leaks and repair as
needed.
Push the lever handle down to close the water supplies, then
reinstall the aerator.
Aerator
Aerator Removal Tool
Kohler Co. 7 1050798-2-A
6. Optional Temperature Limiting Adjustment
NOTE: The water temperature does not need to be adjusted if the
maximum water temperature is below 105°F (41°C).
Lift and turn the lever handle to the full hot position.
Determine the temperature using a thermometer. If the
temperature exceeds 105°F (41°C), complete the following steps.
Using a small flat-blade screwdriver, carefully pry the plug button
off the lever handle.
Loosen the setscrew on the handle with a hex wrench, then
remove the handle and bonnet.
Note the position of the locking ring relative to the inner geared
ring.
NOTE: To avoid damage to the locking ring during removal, pry
each side of the locking ring off the inner geared ring with an equal
and even technique.
Gradually pry each side of the locking ring up off of the inner
geared ring and onto the valve stem with a flat-blade screwdriver.
Rotate the valve stem clockwise to increase temperature, or
counterclockwise to decrease temperature.
Reinstall the locking ring into the inner geared ring.
Reinstall the bonnet and handle to the faucet body.
Test the setting and make any adjustments as needed.
Plug Button
Handle
Bonnet
Inner
Geared
Ring Locking Ring
Setscrew
Locking Ring
Inner Geared
Ring
Valve Stem
1050798-2-A 8 Kohler Co.
Optional Temperature Limiting Adjustment (cont.)
After all adjustments have been made, use a hex wrench to
tighten the setscrew.
Press the plug button into place.
Kohler Co. 9 1050798-2-A
Guide d’installation
Robinet d’évier mono-contrôle
Outils et matériels
Merci d’avoir choisi la compagnie Kohler
Nous apprécions votre engagement envers la qualité Kohler. Veuillez
prendre s’il vous plaît quelques minutes pour lire ce manuel avant de
commencer l’installation. Ne pas hésiter à nous contacter en cas de
problème d’installation ou de performance. Nos numéros de téléphone
et notre adresse du site internet sont au verso. Merci encore d’avoir
choisi la compagnie Kohler.
Avant de commencer
Respecter tous les codes de plomberie et de bâtiment locaux.
Couper l’alimentation d’eau principale.
Vérifier avec soin si les tubes d’évacuation ou d’alimentation
d’eau sont endommagés.
Ce robinet est conçu pour des lavabos à un orifice.
Pour de nouvelles installations, installer le robinet et le drain au
lavabo avant d’installer celui-ci.
Kohler Co. se réserve le droit d’apporter toutes modifications au
design des robinets et ceci sans préavis, comme spécifié dans le
catalogue des prix.
Thermomètre
Clé à
sangle Joint
d'étanchéité
pour filetage
Mastic de
plombier Clé
hexagonale
Tournevis
assortis
Kohler Co. Français-1 1050798-2-A
Table of contents
Languages:
Other Kohler Plumbing Product manuals
Kohler
Kohler 27406-2MB User manual
Kohler
Kohler K-T10585 User manual
Kohler
Kohler K-2293 Assembly instructions
Kohler
Kohler Fairfax K-12185 User manual
Kohler
Kohler K-6228 Assembly instructions
Kohler
Kohler K-15246X-S Assembly instructions
Kohler
Kohler COMPOSED K-25421T User manual
Kohler
Kohler Sterling 20243 Assembly instructions
Kohler
Kohler Rada Tripoint-F 2.1658.011 User manual
Kohler
Kohler K-7825 User manual
Kohler
Kohler K-205 Assembly instructions
Kohler
Kohler K-3099 Assembly instructions
Kohler
Kohler K-3148 K-3150 Assembly instructions
Kohler
Kohler K-7127 User manual
Kohler
Kohler K-13490 Assembly instructions
Kohler
Kohler Triton Rite-Temp K-T6910-2A User manual
Kohler
Kohler Memoirs K-2238 Assembly instructions
Kohler
Kohler 1031338 Manual
Kohler
Kohler K-3323X Assembly instructions
Kohler
Kohler Stillness K-14450 User manual
Popular Plumbing Product manuals by other brands
Weka
Weka 506.2020.00E ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS
UBERHAUS DESIGN
UBERHAUS DESIGN 75175017 Operator's manual
American Standard
American Standard DetectLink 6072121 manual
Uponor
Uponor Contec TS Mounting instructions
Pfister
Pfister Selia 49-SL Quick installation guide
Fortis
Fortis VITRINA 6068700 quick start guide
Elkay
Elkay EDF15AC Installation, care & use manual
Hans Grohe
Hans Grohe AXOR Citterio E 36702000 Instructions for use/assembly instructions
baliv
baliv WT-140 manual
BELLOSTA
BELLOSTA romina 0308/CC Installation instruction
Bristan
Bristan PS2 BAS C D2 Installation instructions & user guide
Crosswater
Crosswater Heir 18-31 installation instructions