Hans Grohe 13241000 User manual

Ecostat 1001 SL

Shower

13261000

Installation Instructions

Ecostat 1001 SL

Shower

13278000

Ecostat 1001 SL

Bath/Shower

13241000

Contents

Safety and Important Information 3

Pack Contents 4

Diniensions 4

Technical Data 5

Supply Conditions TMV2 5

Supply Conditions TMV3 5

Installation Requirements 6-7

Installation

Thermostat 8-9

Commissioning and in-service tests

Commissioning 10

In-service tests 11

Frequency of in-service tests 11

Thermostatic Adjustement

Temperature Limitation 12

Callibrating Thermostat 12

Setting Thermostat Max. Temp. 13

Operating your Shower 14

Cleaning 15

Spare Parts 16-17

Trouble Shooting 18

Warranty 18

If there are any queries regarding this product or its

installation, please contact the Hansgrohe technical

hotline: 0870 7701975

The Ecostat 1001 SL Bath/Shower 13241000

meets the requirements of the TMV2 Scheme.

The Ecostat 1001 SL Shower 13278000

meets the requirements of the TMV2 and TMV3

Scheme.

The Ecostat 1001 SL Shower 13261000

meets the requirements of the TMV2 and TMV3

Scheme.

Safety and Important Information

Hansgrohe products are safe provided they are installed, used and maintained in accordance with these

instructions and recornrnendations.

Please read these instructions thoroughly and retain for future use.

The plumbing installation of this shower must comply with the requirements of UK

Water Regulations/Bylaws (Scotland), Building Regulations or any other regulations specified by the local

Water Authority and supplier.

We strongly recommend that you use a plumber registered with or a member of an Association:

Institute of Plumbing (IOP) - throughout the UK

National Association of Plumbing, Heating and Mechanical Services Contractors

(NAPH & MSC) - England & Wales

Water Industry Approved Plumber Scheme (WIAPS)

Dispose of plastic bags carefully

Keep children well away from the work area.

Check for hidden pipes and cables in the wall before drilling holes.

The unit must be mounted on a finished waterproofed wall surface (usually tiles).

If you are using power tools (e.g. to drill holes) wear safety glasses and always disconnect tools from the

power supply after use.

Do not operate the shower unit if the hand shower or spray hose has been damaged or is blocked.

Do not block the flow of water from the hand shower, by placing it on your hand or any other part of your

body or foreign object.

The thermostatic unit should be serviced annually by a qualified person to ensure maximum safety during

use.

The mixer incorporates check valves (page 16 pos. 4) and filters (page 16 pos 9).

The fitting of isolation valves is required (preferred location page 6 and 7 Installation Requirements)

Dimensions

Pack Contents

Please check that you have been supplied with the

following:

Ecostat 1001 SL Shower

1 Ecostat 1001 SL 3 Escutcheons

2 Mesh washers 4 S-unions

Ecostat 1001 SL Shower

1 Ecostat 1001 SL

2 Mesh washers

Ecostat 1001 SL Shower

Technical Data

Ecostat 1001 SL Bath/Shower

1 Ecostat 1001 SL 3 Escutcheons

2 Mesh washers 4 S-unions

Ecostat 1001 SL Bath/Shower

Ecostat 1001 SL

This thermostatic valve will suit supplies of:

HIGH PRESSURE (HP-S)

Operating pressure: max. 10 bar

Recommended operating pressure: 1 - 5 bar

Test pressure: 16 bar

Hot water temperature: max. 80°C

Recommended hot water temp.: 65°C

Rate of flow from bath spout: 20 l/min. @ 3 bar

Rate of flow from shower outlet:18 l/min. @ 3 bar

Maximum outlet temperature: 43°C +/-*

Safety check: 40°C

Hot water connection: Left hand

Cold water connection: Right hand

Minimum difference between hot

water and mixed water temperature: 6 K

Hot and cold supply pressure should be balanced

Mixed water temperature

Application Mixed water temperature

(at point of discharge)

Operating pressure range High pressure Low pressure

Maximum static pressure - bar 10 10

Flow pressure, hot and cold - bar 1 to 5 0.2 to 1

Hot supply temperature - °C 52 to 65 52 to 65

Cold supply temperature - °C 5 to 20 5 to 20

Bidet 38°C max.

Shower 41°C max.

Washbasin 41°C max.

Bath (44°C fill) 44°C max.

Bath (46°C fill) 46°C max.

* For preset outlet temperature adjustment – See

page 10 „Commisioning“.

NB. If a water supply is fed by gravity then the

supply pressure should be verified to ensure the

conditions of use are appropriate for the valve.

Valves operating outside of these supply conditions

cannot be guaranteed to operate as a TMV2 or

TMV3 valve.

Installation Requirements

This thermostatic mixer valve must be installed in

Supply Conditions TMV2

Supply Conditions TMV3

Operating pressure range High pressure Low pressure

Maximum static pressure - bar 10 10

Flow pressure, hot and cold - bar 1 to 5 0.2 to 1

Hot supply temperature - °C 55 to 65 55 to 65

Cold supply temperature - °C 5 to 25 5 to 25

The following models are TMV3 approved for high

pressure shower (HP-S) application: 13261000

and 13278000

compliance with current Water Regulations. If you

have any doubts about the Water Regulation require-

ments contact your local water services provider or

use the services of a professional plumber.

This mixer valve is suitable for use with the following

water supply systems:

Gas Combination Boiler (multi-point) 1.0 - 10 bar*

Unvented System (pressure balanced) 1.0 - 10 bar

Pumped System 1.0 - 10 bar

IMPORTANT: If you install this mixer with a

gravity fed system, there must be a minimum head

(vertical distance) from the underside of tlie cold

water storage tank to the showerhead position of

at least 1 metre.

Before connecting the mixer, water should be flushed

through the system to remove all debris that might

otherwise damage the valve.

* If pressure is in excess of 3.5 bar, a pressure-

reducing valve should be fitted.

KEY

Isolating valve

Reducing valve

Mixer Valve

Pump

Gas Combination Boiler (multi-point)

Unvented System (pressure balanced)

Pumped System

32 - 41

Seal

Shower Thermostat

PTFE

tape

150 mm

HOT

COLD

Shower Thermostat

1. The hot and cold water outlets should be 150mm

apart (plus or minus 12mm). Hot on the left and

cold on the right (fig. 1). The recommended

plumbing fittings are ½“ back plate elbows (not

supplied).

2. Flush through the hot and cold water supplies.

3. Wrap PTFE tape round the S-unions and screw

into the backplate elbows. The S-unions must

protrude beyond the tiled surface between 32

and 41mm (figs.2-3).

4. Seal the gap between the S-unions and the tiles

(fig.3).

5. Screw the escutcheons onto the S-unions.

6. Fasten the thermostatic mixer onto the S-unions

using the union nuts. Align the unit and tighten

the nuts (be careful not to damage the chrome

finish). The S-unions allow inaccuracies to be

compensated for.

Installation

Bath/Shower Thermostat

As the shower thermostat above (positioned over

a bath).

1Shower Thermostat

180 mm

HOT

COLD

Shower Thermostat

1. The hot and cold water outlets must be exactly

180mm apart. Hot on the left and cold on the

right (fig. 1).

2. Flush through the hot and cold water supplies.

3. Fasten the thermostatic mixer onto the unions

using the union nuts. Tighten the nuts (be careful

not to damage the chrome finish).

Commissioning and in-service

tests

Commissioning

Purpose

Since the installed supply conditions are likely to

be different from those applied in the laboratory

tests it is appropriate, at commissioning, to carry

out some simple checks and tests on each mixing

valve to provide a performance reference point for

future in-service tests.

Procedure

1. Check that:

a) the designation of the thermostatic mixing

valve matches the intended application

b) the supply pressures are within the range of

operating pressures for the designation of

the valve

c) the supply temperatures are within the range

permitted for the valve and by guidance

information on the prevention of legionella

etc.

2. Adjust the temperature of the mixed water in

accordance with the manufacturer’s instructions

and the requirement of the application and then

carry out the following sequence:

a) record the temperature of the hot and cold

water supplies

b) record the temperature of the mixed water

at the largest draw-off flow rate

c) record the temperature of the mixed water

at a smaller draw-off flow rate, which shall

be measured

d) isolate the cold water supply to the mixing

valve and monitor the mixed water tempe-

rature

e) record the maximum temperature achieved

as a result of (d) and the final stabilised

temperature

NOTE: The final stabilised mixed water tempera-

ture should not exceed the values in Table A.

Application Mixed water

temperature

Shower 43°C

Washbasin 43°C

Bath (44°C fill) 46°C

Bath (46°C fill) 48°C

f) record the equipment, thermometer etc. used

for the measurements

Table A: Guide to maximum stabilised

temperatures recorded during site

tests

This manual suits for next models

Table of contents

Other Hans Grohe Plumbing Product manuals

Hans Grohe

Hans Grohe ShowerTablet Select 700 13184000 Manual

Hans Grohe

Hans Grohe Aquaclub 1 28352 Series User manual

Hans Grohe

Hans Grohe Brushed Nickel 04193820 User manual

Hans Grohe

Hans Grohe Focus M43 120 1jet 71816 Series Manual

Hans Grohe

Hans Grohe AXOR Citterio 3911600 Series Manual

Hans Grohe

Hans Grohe Finoris 230 76060 0 Series Manual

Hans Grohe

Hans Grohe Raindance Select 26468000 Manual

Hans Grohe

Hans Grohe PuraVida 15472000 Manual

Hans Grohe

Hans Grohe Axor Starck 104801 Series Installation guide

Hans Grohe

Hans Grohe AXOR Citterio Series Manual

Hans Grohe

Hans Grohe Swing C 06117 0 Series Installation guide

Hans Grohe

Hans Grohe AXOR Edge 46460 1 Series Instruction Manual

Hans Grohe

Hans Grohe Pulsify E 260 2jet 24350 Series Manual

Hans Grohe

Hans Grohe Fixfit Square 26455 3 Series Manual

Hans Grohe

Hans Grohe Showerpipe Croma 220 27222000 Manual

Hans Grohe

Hans Grohe Ecos Manual

Hans Grohe

Hans Grohe Axor Uno 38111180 User manual

Hans Grohe

Hans Grohe Shower Select 15765000 Manual

Hans Grohe

Hans Grohe Talis E 80 71706000 Manual

Hans Grohe

Hans Grohe Raindance S 27636 0 Series Instruction Manual

Hans Grohe

Hans Grohe 28307000 Manual

Hans Grohe

Hans Grohe Focus User manual

Hans Grohe

Hans Grohe PuraVida 15472 Series User manual

Hans Grohe

Hans Grohe FORMAT Pro 72644000 Manual

Popular Plumbing Product manuals by other brands

Weka

Weka 506.2020.00E ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS

Kohler

Kohler K-6228 Installation and care guide

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Operator's manual

American Standard

American Standard DetectLink 6072121 manual

Uponor

Uponor Contec TS Mounting instructions

Pfister

Pfister Selia 49-SL Quick installation guide

Fortis

Fortis VITRINA 6068700 quick start guide

Fortis

Fortis MILANO 78211JS installation instructions

Kohler

Kohler K-12183 Homeowner's guide

Maxxus

Maxxus MX-M206-01 instruction manual

Moen

Moen 5922 Series installation instructions

Viega

Viega Prevista Pure 8512 Instructions for use

Kohler

Kohler Centerset K-15240 Homeowner's guide

Viega

Viega Prevista Dry 8522.33 Instructions for use

Sanela

Sanela Lema SLP 59RB Instructions for use

Elkay

Elkay EDF15AC Installation, care & use manual

baliv

baliv WT-140 manual

Kohler

Kohler Mira Eco Installation & user guide