Hafele SAFE-O-TRONIC LS 100 User manual
SAFE-O-TRONIC® access
Item No.: 231.98.000/001/002/003
Mounting Instructions
Dimensions in mm
Inches are approximate
Electronic Identification and Locking System
SAFE-O-TRONIC® LS Cabinet Lock
Manual
LS 100
2
® Copyright 2010 by Schulte-Schlagbaum AG
Nevigeser Straße 100-110
D-42553 Velbert
Phone: +49 2051 2086-0
http:/www.sag-schlagbaum.com
Document number: 6-703-2 34R1.0
• This manual replaces all previous versions.
• The details in this manual are subject to change without prior notification.
• The compilation of the information in this manual is carried out to the best of our knowledge.
Schulte-Schlagbaum AG does not assume any liability for the correctness and completeness of the
details in this manual. In particular, Schulte-Schlagbaum AG cannot be held liable for consequential
damages on account of faulty or incomplete details.
• Relaying and duplication of this document and the exploitation and communication of its contents
are not permitted unless expressly allowed. Violations shall obligate to provide compensation for
damages. All rights reserved in the event of patent grant or registration of a utility model or design.
Means of depiction
The following means of depiction are used in this manual:
Notice
Please observe this important information.
Handling instructions
These mark a work step during user input.
SAFE-O-TRONIC® is a registered trademark of Schulte-Schlagbaum AG.
Safety and warning notes
Please read before initial operation.
• This manual describes the initial operation and operation of a SAFE-O-TRONIC® LS 100.
• The equipment must only be used for the purpose intended by the manufacturer.
• Please keep the instruction manual in an easily accessible place.
• Unauthorized amendments and the use of spare parts and auxiliary devices that are not sold or
recommended by the manufacturer of the equipment can cause fires, electric shocks and injuries.
The manufacturer will not be liable.
• Repair work must only be carried out by the manufacturer.
• The warranty provisions of the manufacturer as amended on the date of purchase shall apply to the
equipment. Liability will not be assumed for unsuitable and automatic compilation of parameters for a
device or unsuitable application of a device.
• The operating company shall bear the responsibility that the device is installed and connected
according to recognized technical rules in the country of installation as well as other valid regulations.
Notes on this manual
3
Notes on this manual..................................................................................... 2
Safety and warning notes............................................................................. 2
Table of contents............................................................................................ 3
Control elements............................................................................................ 4
Lock with mounting components................................................................. 5
Installation information................................................................................. 6
Preparation of the door.......................................................................................... 6
Installation........................................................................................................... 6
Replacement of the rotary knob (as needed)............................................................... 6
Setting the rotational direction for locking.................................................................. 7
Replacing the plate (e.g. for numbers, logo, etc.)......................................................... 8
General information....................................................................................... 9
Capacitive keypad................................................................................................. 9
UserCode............................................................................................................ 9
MasterCode1........................................................................................................ 9
MasterCode2........................................................................................................ 9
Code overview...................................................................................................... 9
Operation............................................................................................................ 10
Function control............................................................................................. 10
Initial operation.............................................................................................. 11
Programming MasterCode2.................................................................................... 11
Locking and opening using MasterCode2................................................................... 12
Locking and opening using the UserCode.................................................................. 12
Further functions........................................................................................... 13
Altering MasterCode2............................................................................................ 13
Programming MasterCode1.................................................................................... 14
Opening using MasterCode1.................................................................................... 15
Release using MasterCode2.................................................................................... 15
Further information........................................................................................ 16
LED display.......................................................................................................... 16
Troubleshooting / operating errors............................................................................ 17
Replacing the battery............................................................................................. 17
Battery monitoring / battery alarm............................................................................ 17
Maintenance and care........................................................................................... 17
Technical Data..................................................................................................... 18
Drilling template................................................................................................... 19
Table of Contents
4
LED display red / green
Capacity keypad
Exchangeable plate
Rotary knob
OK key: Finish of Code entry
Abort key: Code entries or programming operations can be rejected by
pressing the abort key
Keys 1, 2, 3, 4, 5, 6, 7, 8, 9, 0: Number keys for Code entry
√
X
21
3
5
7
9
4
6
8
0
Control Elements
5
Lock with Mounting Components
1 Lock
2 Nut for mounting the lock on the door
3 Grommet for setting the rotational direction of the rotary knob in order to lock
4 Locking cam (A cropped or hook-shaped locking lever can also be used depending on the properties and
condition of the cabinet.)
5 Fastening bolt for locking lever
6 Bushing for fastening the lock to the door for door thickness from 10 mm to 18 mm
7 Bushing for fastening the lock to the door for door thickness from 1 mm to 9 mm
8 Screw for fastening the lock to the door
9 Rotary knob
6
Preparation of the door
The following holes must exist in the door corresponding to the drawing:
1. Punched hole, dimensions 19.1 mm / 16 mm. A round hole with a diameter of 19.1 mm can also be
drilled at this position.
2. Round hole with a diameter of 7 mm.
As soon as the first hole exists, as described in 1, the 7 mm round hole can be drilled by using a drilling tem-
plate (e.g. the drilling template at the end of the manual).
Installation
1. Insert the lock (1) into the two holes 19.1 mm / 16 mm and 7 mm
2. Fasten the lock (1) using the nut (2)
3. Screw on the lock (1) using the screw (8) and the bushing (6 or 7) depending on the thickness of the door
4. Fasten the grommet (3) for setting the rotational direction and the locking cam (4) using the bolt (5)
5. Test the lock function by means of the TestCode when the door is open
6. Test the function when the door is closed
Replacement of the rotary knob (as needed)
1. Remove the bolt (5).
2. Use a TG 10 screwdriver to loosen the fastening screw for the rotary knob by
inserting through the threaded hole for the bolt (5).
3. Fasten the new rotary knob in reversed order.
Installation Information
7
Installation Information
Settng the rotational direction for locking
The setting of the rotational direction described here is for a lock with a rotary knob that is turned to the left
for locking.
1 Lock marked with left handed rotational direction for locking
2 Grommet that is attached to the lock on the inside of the door. The opening marked “L” points
downwards.
3 Rear side of the lock to which the grommet is attached.
If the lock is installed in a position whereby the rotary knob is not at the top (e.g. horizontal installation), the
grommet must be turned accordingly.
If the rotary knob is to be turned to the right for locking, the grommet must be attached to the lock in such a
way that the “R” opening points downwards.
8
Installation Information
Replacing the plate (e.g. for numbers, logo, etc.)
After inserting a small screwdriver into the center of the plate, the old plate is levered out of the lock. A new
plate can then be snapped in.
Notice: The old plate is destroyed when the plate is replaced.
9
Capacitive keypad
The SAFE-O-TRONIC® LS 100 uses a capacitive keypad.
Notice: The capacitive keypad cannot be operated if you are wearing gloves.
UserCode
The UserCode serves locking or opening of the cabinet or locker by the user. Any four-digit code can be
programmed as the UserCode.
MasterCode1
MasterCode1 serves the plant operator to open the locker. It is intended for employees with restricted
locking authorizations. After being opened, the lock is blocked for the entry of a new UserCode and has to
be released with the help of the MasterCode2. A 5 digit code can be programmed as MasterCode1. If the
employees are only aware of the MasterCode1, they are protected against suspicion in cases of hidden
thefts. It means if there is a theft and the compartment has been locked again, the employees cannot come
into question as offenders.
Notice: MasterCode1 cannot be programmed with 0 as the first number!
MasterCode2
MasterCode2 can be used by the operator of the facility at any time to open and close the compartment or
release the lock. A 5 digit code can be programmed as MasterCode2.
Notice: MasterCode2 cannot be programmed with 0 as the first number!
Code overview
The following table contains an overview of the various codes.
(*) Notice: After using MasterCode1 to open the locker, the lock must be released
by entering MasterCode2 (see page 15).
General Information
4-digit 5 digit Open Close
UserCode x - x x
MasterCode1 - x x(*) -
MasterCode2 - x x x
10
Operation
Operation is supported by the red/green LED display and an acoustic acknowledgement by means of signal
transmitters.
The key can be used to abort an input procedure.
The procedure is aborted automatically if there is a stop of more than three seconds between operating the
individual keys.
You have four attempts to enter the correct code. After the fourth incorrect entry the entry process is disabled
for one minute as protection against manipulation. The lock is blocked after 100 incorrect entries. Blocking
can only be released with MasterCode2.
All locks in the SAFE-O-TRONIC® LS 100 series are delivered with the same factory setting. The TestCode
for locking and opening is activated in the factory setting.
TestCode
The TestCode can be used to carry out a simple SAFE-O- TRONIC® LS 100 functionality check.
Locking and opening using the TestCode
Press the 0 key
Afterwards press the OK key
Turn the knob
Notice: The TestCode is retained until initial operation.
General Information
Function control
√
X
0
This manual suits for next models
4
Table of contents
Other Hafele Lock manuals
Hafele
Hafele dialock DT 100 User manual
Hafele
Hafele 233.47.000 User manual
Hafele
Hafele Sola User manual
Hafele
Hafele Versa Mini 231.98.345 User manual
Hafele
Hafele DT 710 User manual
Hafele
Hafele dialock DTSH User manual
Hafele
Hafele DT 700 User manual
Hafele
Hafele ER5000 User manual
Hafele
Hafele DT 400 User manual
Hafele
Hafele DT 750 User manual
