GROLAB POWERBOT User manual
www.opengrow.pt
POWERBOT
EN
E
S
FR
(HW03, HW04)
INSTALLATION
MANUAL
MANUAL DE INSTALACIÓN
MANUEL D'INSTALLATION
®
© 2019 Open Grow, LDA. All rights reserved.
IMPB2019V01
E
S
EN
FR
1
1
110 ~ 230VAC
10A
1
2
9
4321
CONTROL
RESET
8
10
15
3
EN
E
S
FR
2
6
TEMP/HUMI
4 5
FIRMWARE CO2SENSOR
7
1
10
13
11
13
FLOOD
12 13
16
POWER SWITCH
14 15
FUSE
10A
E
S
EN
FR
3
17
19
18
E
S
EN
FR
4
1
2
3
4
5
6
7
8
9
10
11
12
13
E
S
EN
FR
110~230VAC power outlet
Module reset buon
Manual switch buons
External switch input
Temperature & humidity sensor outlet
Mul sensor connecon outlet
Output status signal LED
Brackets for wall-mounng
Universal socket outlet
RF antenna outlet
Flood detector outlet
Module status signal LED
Type-B USB outlet (for Firmware update)
5
Protecon fuse socket
RF communicaons antenna
Type-B USB (for Firmware update)
Main power swch
Temperature/humidity sensor
Power cord 110~230VAC - 10A
INSTALLATION
Screw the communicaon antenna (16) into
the module port (13). For correct communica-
on, turn the antenna in order to posion it
vercally according to the direcon of the
module.
Peripherals connecon
1
14
15
16
17
18
19
E
S
EN
FR
Screw the communicaon antenna (16) into
t
-
on, turn the antenna in order to posion it
vercally according to the direcon of the
m
P
6
16
13
Place the module on a firm surface, far from
flood-prone areas. It is recommended that the
module be mounted on a wall with the fixing
holes on the upper part.
Once the module has been mounted, connect
the power cable (19) to the module’s power
outlet (1) and the other end to a 110~230VAC
outlet.
110 ~ 230VAC
10A
19
1
E
S
EN
FR
Place the module on a firm surface, far from
flood-prone areas. It is recommended that the
module be mounted on a wall with the fixing
h
Once the module has been mounted, connect
the power cable (19) to the module’s power
o
C
o
7
Place the sensor at the height of the plants
where you could monitor the environmental
state of the growing area correctly.
TEMP/HUMI FIRMWARE
1
45
6
Connect the temperature and humidity
sensor (18) to the module’s outlet (5).
18
E
S
EN
FR
Place the sensor at the height of the plants
where you could monitor the environmental
s
Connect the temperature and humidity
s
8
Connect your peripherals to the module’s
power outlets (11). Each outlet has a idenfi-
cator and a LED displaying the output state
(9). Each output is configurable via soware,
so you can plug any device to any outlet.
If you connect mulple devices to one outlet,
remember not to surpass the power limits,
which is for each outlet and in total per
module:
2300W (230vAC - EU) / 1100W (110vAC - USA)
Never positon the sensor too close to a light
source, wet it, or put it in high (90%~100%)
humidity values for a long periods of me,
this can damage your sensor.
18
11
9
E
S
EN
FR
Connect your peripherals to the module’s
p
-
cator and a LED displaying the output state
(9). Each output is configurable via soware,
s
If you connect mulple devices to one outlet,
r
,
which is for each outlet and in total per
m
2
)
Never positon the sensor too close to a light
source, wet it, or put it in high (90%~100%)
humidity values for a long periods of me,
t
9
This manual suits for next models
2
Table of contents
Languages:
Other GROLAB Lawn And Garden Equipment manuals
Popular Lawn And Garden Equipment manuals by other brands
Vertex
Vertex 1/3 HP Maintenance instructions
GHE
GHE AeroFlo 80 manual
Millcreek
Millcreek 406 Operator's manual
Land Pride
Land Pride Post Hole Diggers HD25 Operator's manual
extraspace
extraspace GardenStore Assembly instructions
Yazoo/Kees
Yazoo/Kees Z9 Commercial Collection System Z9A Operator's & parts manual
