Contec AD12-64(PCI) User manual
AD12-64(PCI)
AD12-16(PCI)
64/16 Channel Analog to Digital Input
Board for PCI
User’s Guide
AD12-64(PCI), AD12-16(PCI) i
Copyright
Copyright 1999 CONTEC Co., LTD. ALL RIGHTS RESERVED
No part of this document may be copied or reproduced in any form
by any means without prior written consent of CONTEC Co., LTD.
CONTEC Co., LTD. makes no commitment to update or keep
current the information contained in this document.
The information in this document is subject to change without
notice.
All relevant issues have been considered in the preparation of this
document. Should you notice an omission or any questionable
item in this document, please feel free to notify
CONTEC Co., LTD.
Regardless of the foregoing statement, CONTEC assumes no
responsibility for any errors that may appear in this document nor
for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft, MS-DOS and Windows are trademarks of Microsoft
Corporation. Other brand and product names are trademarks of their
respective holder.
AD12-64(PCI), AD12-16(PCI)ii
Product Configuration
-AD12-64(PCI)/AD12-16(PCI) board…1
-User's Guide (This Booklet)…1
Unpacking:
This board is specially packed in an anti-static bag to prevent
damage in shipping.
Check the contents to make sure that you have everything listed
above. If you do not have all the items, contact your distributor
or CONTEC group office where you purchased.
Note!
Do not remove the board from its protective packaging until the
computer case is open and ready for installation. Electrical static
can cause damage to electrical components.
AD12-64(PCI), AD12-16(PCI) iii
Table of Contents
Copyright............................................................................i
Trademarks ........................................................................i
Product Configuration ..................................................... ii
1. Introduction .............................................................1
Features.........................................................................1
Limited Three-Year Warranty......................................3
How to Obtain Service..................................................3
Liability .........................................................................3
About this Manual ........................................................4
2. Setup ....................................................................... 5
Setup Components of the Board.......................................5
Names of Components ..................................................5
Setting on Board Jumpers and Switch ............................6
Setting the Board ID.....................................................6
Setting procedure..........................................................6
Installing the Board on Your PC and Turning
the Power On.....................................................................6
Setting up the Board.........................................................7
Installing for Windows 98 ............................................7
Installing for Windows 95 .......................................... 11
Installing for Windows NT .........................................18
Installing for other OS System ..................................19
3. Connecting an External Device................................21
Interface Connector.........................................................21
AD12-64(PCI) CN1 Pin Assignments to Signals.......21
AD12-16(PCI) CN1 Pin Assignments to Signals.......23
Connecting the Analog Input Signals ............................25
Connection example in single-ended input mode......25
Connection example in differential input mode........27
Connecting the Digital Input/Output Signals and
Control Signals................................................................29
AD12-64(PCI), AD12-16(PCI)iv
4. Functions and Operating Procedures........................ 31
Functional Overview.......................................................31
Description ......................................................................31
Analog Input Function ...............................................31
Initialization process ..................................................33
Specifying sampling conditions..................................34
Specifying input range................................................36
Setting internal sampling clock .................................38
Starting sampling operation ......................................39
Feeding conversion data.............................................40
Details of analog input status ....................................42
Digital input function .................................................44
Digital output function ...............................................44
Interrupt function.......................................................45
External trigger ..........................................................47
Timer ...........................................................................48
Status of external trigger and timer..........................50
I/O address map list....................................................51
Command list ..............................................................53
5. Sample Program for MS-DOS.................................. 55
Preparation .................................................................56
6. Calibration Procedures............................................ 59
7. System Reference.................................................... 61
Specifications...................................................................61
Block Diagram.................................................................62
External Sampling Clock Operation Timing .................63
8. Index ..................................................................... 65
AD12-64(PCI), AD12-16(PCI) v
List of Figures
Figure 2.1. Names of Components.............................................. 5
Figure 2.2. Board ID Setting (SW1)........................................... 6
Figure 3.1. AD12-64(PCI) CN1 Pin Assignments to Signals.... 21
Figure 3.2. AD12-16(PCI) CN1 Pin Assignments to Signals.... 23
Figure 3.3. Connection for the Single-ended Input (via a Flat
Cable)..................................................................... 25
Figure 3.4. Connecting the Single-end Input (via a shielded
Cable)..................................................................... 25
Figure 3.5. Connection for the Differential Input (via a Flat
Cable)..................................................................... 27
Figure 3.6. Connection for the Differential Input (via a Shielded
Cable)..................................................................... 27
Figure 3.7. Connecting the Control Signal Inputs..................... 29
Figure 3.8. Connecting the Control Signal Outputs.................. 29
Figure 4.1. Basic operation for analog input............................. 32
Figure 4.2. Analog input procedures......................................... 32
Figure 4.3. Procedures for setting input range .......................... 36
Figure 4.4. Input conversion data ............................................. 40
Figure 4.5. Timing for setting/resetting sampling busy status... 42
Figure 4.6. Timing for setting/resetting data overwrite error status
............................................................................... 43
Figure 6.1. Instruments for Calibration..................................... 59
Figure 7.1. Board Dimensions.................................................. 62
Figure 7.2. Circuit Block Diagram............................................ 62
Figure 7.3. External Sampling Clock Operation Timing Diagram
............................................................................... 63
AD12-64(PCI), AD12-16(PCI)vi
List of Tables
Table 4.1. Input range and setting data ...................................... 36
Table 4.2. Example conversion data in a ±10 –volt range
conversion.............................................................. 40
Table 4.3. Output port list.......................................................... 51
Table 4.4. Input port list ............................................................ 52
Table 4.5. Command list............................................................ 53
Table 6.1. Correspondence between Analog Input Circuit
Adjusting Trimmers and Channels.......................... 59
Table 7.1. Specifications............................................................ 61
Table 7.2. Description for each portion...................................... 63
Introduction
AD12-64(PCI), AD12-16(PCI) 1
1. Introduction
Thank you for purchasing our non-insulated type analog input
board. The product is a PCI-compliant analog input board, which
is provided with analog input function for converting analog signals
into digital signals, digital input/output function, and programmable
timer function. This board is used by inserting it in a PCI-bus
expansion slot on a PC main unit or a slot on an I/O expansion unit.
Read this manual carefully for setting up the board and connecting
the board to peripheral devices. For building an application under
Windows 98, Windows 95, or Windows NT environment, use
optionally available support software.
Support software sold separately
API-PAC(W32) Ver. Aug. 1999 or later
The API-PAC(W32) does not necessarily support full functions of
the board. Make sure specifications of the driver software before
purchase.
Features
-Multi-channel analog input capability
64 single-ended analog inputs or 32 differential analog inputs
(AD12-64(PCI)). 16 single-ended analog inputs or 8 differential
analog inputs (AD12-16(PCI)). Single-ended or differential
input is selected by software.
-8-type selectable input ranges
Input ranges are selectable among 8-types including both unipolar
and bipolar inputs. Ranges are selectable for each channel, and
changing ranges is allowed under operation.
-Sampling control
Two types of sampling functions are provided, namely sampling
by software command and periodical sampling in synchronization
with sampling clock. Either a special-purpose clock signal on
board or an external clock signal is selectable as a sampling
clock.
Introduction
AD12-64(PCI), AD12-16(PCI)2
-Digital input/output
The board is capable of four TTL-level digital inputs and four
TTL-level digital outputs.
-Programmable timer function
The board is provided with an independent programmable timer.
The timer allows generating interrupts and outputting count-up
signals at regular intervals. The timer can be monitored on the
basis of status without using interrupt capability.
-External trigger input capability
The board allows generating an interrupt by inputting a TTL-level
digital signal. Also, trigger input can be monitored on the basis
of status without using interrupt capability. Status of input
signals can be monitored directly. This function is independent
of other functions.
-Capability of generating interrupts by multiple causes
The board is capable of monitoring sampling operation,
programmable timer, or external trigger, etc. simultaneously.
-The following optional devices are available for easier connecting
and wiring
Relay terminal box EPD-96 *
96-pin half-pitch connector shield cable (one end)
PCA96PS
96-pin half-pitch connector shield cable (both ends)
PCB96PS
* An optional cable (PCB96PS) is required separately.
Introduction
AD12-64(PCI), AD12-16(PCI) 3
Limited Three-Year Warranty
CONTEC Interface boards are warranted by CONTEC Co., LTD. to
be free from defects in material and workmanship for up to three
years from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned
freight prepaid with a copy of the original invoice and a Return
Merchandise Authorization to the distributor or the CONTEC group
office, from which it was purchased.
This warranty is not applicable for scratches or normal wear, but
only for the electronic circuitry and original boards. The warranty
is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the
original invoice is not included, in which case repairs will be
considered beyond the warranty policy.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a
copy of the original invoice. Please obtain a Return Merchandise
Authorization Number (RMA) from the CONTEC group office
where you purchased before returning any product.
*No product will be accepted by CONTEC group without the
RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the
product. In no event will the warrantor be liable for any incidental
or consequential damages due to such defect or consequences that
arise from inexperienced usage, misuse, or malfunction of this
device.
Other manuals for AD12-64(PCI)
2
This manual suits for next models
1
Table of contents
Other Contec PCI Card manuals
Contec
Contec PI-64L Series User manual
Contec
Contec PIO-64/64L(PCI)H User manual
Contec
Contec COM-2PD-LPE User manual
Contec
Contec AIO-160802LI-PE User manual
Contec
Contec DIO-0808L-PCI User manual
Contec
Contec IPC SERIES User manual
Contec
Contec AO-1616L-LPE User manual
Contec
Contec DIO-48D-LPE User manual
Contec
Contec DS540-MPCI4WAP User manual
Contec
Contec FX-DS540-MPCI6 User manual
Contec
Contec ADI12-16(PCI) User manual
Contec
Contec SMC-4DF-PCI User manual
Contec
Contec COM-4(PCI)H User manual
Contec
Contec CNT24-4D(PCI)H User manual
Contec
Contec AO-1604CI3-PCI User manual
Contec
Contec ADA16-32/2(PCI)F User manual
Contec
Contec CNT-3208M-PE User manual
Contec
Contec DIO-1616B-LPE User manual
Contec
Contec DIG-100M1002-PCI User manual
Contec
Contec PIO-16/16RL(PCI)H User manual
Popular PCI Card manuals by other brands
Conrad Electronic
Conrad Electronic 97 46 71 operating instructions
Micro Innovations
Micro Innovations USB650A Quick installation guide
KTI Networks
KTI Networks KF-310 user guide
Asus
Asus SpaceLink WL230 user manual
SIIG
SIIG SC2475 Quick installation guide
TRENDnet
TRENDnet TEW-703PI Quick installation guide
