Arjo Maxi Sky 2 PLUS User manual
2
Pull each leg strap under the thigh
so that it emerges on the inside of
the thigh.
1
Place the sling around the
patient. If the sling has a head
support, extend it to the top of
the patient’s head.
Place the attachment loop
on the hook.
Make sure that the safety
latch is closed.
34
Place the spreader bars at 45° and close enough to
attach the shoulder loops, then the leg loops.
Raise the foot end of the spreader bar first using the
Recline button to create tension in the leg loops.
Make sure that the sling is properly installed
and encircles the patient's buttocks to
provide better support.
56
Raise the patient.
Move the patient.
7
8
Lower until there is no tension in
the loops. Detach the leg loops,
then the shoulder loops.
001-31310-EN Rev 1 • 03/2021 • Page 1/4
QUICK REFERENCE GUIDE - USE
Maxi Sky 2 PLUS
Transfer from seated to supine position
1
Roll the patient onto their side. Fold the sling
in half and place it on the bed along the back
of the patient.
2
Roll the patient back onto the sling and then roll the
patient in the opposite direction, so that the folded
part of the sling can be straightened out.
5
Raise the patient.
6
Move the patient.
Place the attachment loop on
the hook.
Make sure that the safety latch
is closed.
3
4
Place the spreader bar in a flat position and close
enough to attach the loops.
Connect the sling’s shoulder and leg loops to the
spreader bar.
7
Lower until there is no tension
in the loops. Detach the leg
loops, then the shoulder loops.
001-31310-EN Rev 1 • 03/2021 • Page 2/4
Transfer from supine to seated position
Attach as many sling loops
as possible to the spreader
bar.
3
1
Place the sling under the
patient and position the lift
over the patient.
4
Raise until the hips are
supported and move up
or to the side.
Lower the patient onto the
bed and detach all of the
sling loops.
5
Place the attachment
loop on the hook.
Make sure that the
safety latch is closed.
2
Place the attachment
loop on the hook.
Make sure that the
safety latch is closed.
2 3
Attach as many sling loops as possible from
one side of the sling to the spreader bar.
Raise until the patient is rolled into the
desired position.
Lower until there is no tension in
the loops and disconnect all of
them.
41
Place the sling under the patient
and position the lift over the patient.
Place the spreader bars at 45° to
attach the loops.
001-31310-EN Rev 1 • 03/2021 • Page 3/4
Repositioning - move up or to the side of the bed
Repositioning - turning in bed
4
Move the patient toward the new
surface. Position the patient centrally
over the new surface.
5
Lower the patient onto the bed.
Lower the spreader bar farther down to detach the loops.
Raise the spreader bar and move the ceiling lift away from the patient.
Place the attachment loop
on the hook.
Make sure that the safety
latch is closed.
23
Attach the loops to the spreader bar.
Raise the patient until the patient is fully
supported.
Position the lift close enough
to attach the loops.
1
ArjoHuntleigh AB
Hans Michelsensgatan 10
211 20 Malmö, Sweden
www.arjo.com
Lateral transfer - between adjacent flat surfaces
001-31310-EN Rev 1 • 03/2021 • Page 4/4
Other manuals for Maxi Sky 2 PLUS
2
Other Arjo Medical Equipment manuals
Arjo
Arjo CARENDO User manual
Arjo
Arjo MAA6000 User manual
Arjo
Arjo Alpha Active 5 User manual
Arjo
Arjo MAA4020M User manual
Arjo
Arjo Enterprise ENT-ACC05 User manual
Arjo
Arjo Lifeguard LG20 User manual
Arjo
Arjo AtmosAir User manual
Arjo
Arjo Bolero User manual
Arjo
Arjo Alpha Active User manual
Arjo
Arjo Tenor Installation guide
Arjo
Arjo MLAAS2000 User manual
Arjo
Arjo Auralis User manual
Arjo
Arjo Alpha Trancell Deluxe User manual
Arjo
Arjo Alenti User manual
Arjo
Arjo Prioma Series User manual
Arjo
Arjo Enterprise E8000X User manual
Arjo
Arjo Prioma User manual
Arjo
Arjo Maxi Sky 1000 User manual
Arjo
Arjo Assembly instructions User manual
Arjo
Arjo Pentalex Plus User manual
