Warranty:
The device itself ( battery excluded) comes with one year warranty from purchasing date if it is operated
under normal circumstances without evidence of tampering. See exclusions below.
Warranty exclusions:
1. If user does not properly operate the device according to the instructions as described in this manual.
2. If the device shows signs of tampering or attempted modification.
3. Improper handling, such as dropping, liquid or cleaner damage.
4. Natural disasters (such as fire, flood, earthquake, thunder strike).
5. If you do not have a receipt or proof of purchase showing date of purchase.
If the thermometer does not function properly, please contact 180 Innovations at
www.180innovations.com or call customer service at 1-877-299-6700. Our representative will
provide further instruction on how to correct the trouble or will ask you to return it for repair or
replacement.
LIMITED WARRANTY
LOT NUMBER INFORMATION
1. Please use a cotton swab or pad moistened with 70~75% isopropyl (rubbing) alcohol to wipe the
probe and device with care, and allow it to fully dry for at least 5 minutes.
2. Use a cloth dampened with water or neutral detergent to clean and dry the device.
3. Do not use thinner, benzene, and other harsh cleaners for cleaning the device.
4. Do not immerse the unit in water or liquid of any kind. The unit is not water proof.
CLEAN & DISINFECTION
Do not submerse or expose the device to water. The unit is not water proof.
Do not use corrosive detergent to clean the device. Clean and disinfect the thermometer
before and after use.
1. Do not drop or crush the device. It is not shock proof.
2. Do not dismantle or modify the device other than changing the batteries.
3. Do not store the device in an extreme environment with direct sunlight, high/low temperatures
or in a location with high humidity or severe dust.
Please contact your local agents or distributors if the device does not function properly as specified
under PRODUCT SPECIFICATION.
CARE & STORAGE
TROUBLESHOOTING
Higher than measuring range.
Lower than measuring range.
Low battery indication, please replace batteries.
The ambient (room) temperature was outside the operating range.
Keep unit at room temperature (approx. 60 - 104° F / 16 - 40° C) for 30 minutes
prior to using.
self-diagonostic error.
0.787inch
(2cm)
0.787inch
(2cm)
USE
MEASUREMENT CONSIDERATION
CAUTION:
1. Make sure the measuring site is dry, clean prior to measurement taking.
2. Clean the probe before and after each measurement to prevent cross-contamination, see
CLEANING & DISINFECTION.
3. After cleaning and disinfection, please wait at least 2 minutes to do a measurement.
FOREHEAD MEASUREMENT
1. Press and release the ON/OFF button to turn on the device.
2. Aim at the forehead within measuring distance 0.787inch(2cm).
3. Press and release the ON/OFF button to do a measurement
4. Read the temperature on the LCD.
NOTE : The switch is at UP position.
OBJECT MEASUREMENT
1. Switch to object measuring mode.
2. Aim at the object within measuring distance 0.787inch(2cm).
3. Press and release the ON/OFF button to do a measurement
4. Read the temperature on the LCD.
NOTE : The switch is at DOWN position.
DOING A MEASUREMENT
1. Press and release the ON/OFF button to turn on the device.
2. The device will be ready for measuring.
3. Press and release the ON/OFF button then read the temperature; after two beeps, it is ready for next
measurements.
4. Device will beep in accordance with the temperature, when the reading is higher than 99.5°F(37.5°C),
the device will have fever alarm.
5. The backlight will light up in accordance with the temperature, shown as below.
Backlight
Red Backlight
Green Backlight
Yellow Backlight
Reading (°C)
37.5 ≤ T
T ≤ 37.1
37.2 ≤ T ≤ 37.4
Reading (°F)
99.5 ≤ T
T ≤ 98.8
99.0 ≤ T ≤ 99.4
ISO 13485Certification
PRODUCT SPECIFICATION
Forehead, Object
Forehead : 71.6°F ~109.9°F(22.0°C ~ 43.3°C)
Object：32°F ~212°F (0°C ~ 100°C)
Forehead: 95.9~107.6°F：±0.4°F, Other : ：±0.5°F
(35.5~42.0°C: ±0.2°C, Other：±0.3°C)
Around 0.787inch(2 cm)
1 second
Measuring Sites
Measuring Range
Accuracy
9 sets
Memory Sets
Measuring Distance
Measuring Time
More than 45000 measurements (exclude Bluetooth transmission)
Battery Life
AAA battery x 2
Battery
Approx. 1.63 x 1.73 x 4.88 inch (41.4 x 44 x 124 mm)Dimension
60.8~104.0°F(16.0~40.0°C), R.H. of 15~95% non-condensing
Operating Condition
After 10 seconds of inactivity
Auto Shut Off
1 year
Warranty
Approx. 88g including batteries
Weight
°F(°C)
Measuring Unit
0.1°F(0.1°C)
Resolution
-4.0~122.0°F(-20.0~50.0°C),R.H. of 15~95% non-condensingStorage Condition
275 inch (7 m) without barrier
Bluetooth Working Area
Compliance ASTM E1965-98
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC STATEMENT
Auto Set and Recall Memory
1. When the device is off or in clock mode, remove the battery cover.
2. Press and release the Bluetooth button, device shows ,
the device is trying to connect to mobile device.
3. When the bluetooth connection is paired, LCD shows then shows , it mean OUcare
can do operation for device.
4. After step 3, OUcare APP will set the device in accordance with these setting then recall all
memory back automatically.
5. OUcare APP shows last memory and speak by specified language, shown as figure1.
NOTE : Connection will be broken if there is no operation within 30 seconds.
Manual Set
1. Press to modify these setting, shows as figure2 again.
2. Press to set these setting into the device, once set succesfully, device shows and
beep.
3. Per above, device shows these setting. -> -> ->
NOTE : Date, time format is in accordance with mobile device.
NOTE : REMINDER is the alarm clock.
NOTE : When the clock alarms, press ON/OFF button to turn off it.
NOTE : Select "CLEAR DATA" will delete all memory of the device,
please double confirm before this operation.
BLUETOOTH
Before Using
1.Install OUcare APP from Google play or App Store successfully. OUcare not only collect
temperatures but also can do setting to device, graph for checking temperature’s trend easily.
2. Press to turn on Bluetooth.
NOTE : Before using this product, recommended to do setting from OUcare APP to device.
(DATE) (DATE) (TIME) (REMINDER)
Figure1 Figure2
LOT NO. (YYMM) on the device label means the year and month of manufacturing. For example,
"2101" means the device was manufactured in January, 2021.
Thank you for purchacing a 180 INNOVATIONS product.
Distributed by: 180 INNOVATIONS DENVER, CO 80204
Manufactured by: K-Jump Health Co LTD
Made in China www.180innovations.com REV.20210125 PN.8283600010
UP
(Forehead, default)
DOWN
(Object)
